Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Wiley eBooks

Radio‐Frequency (rf) SQUID

Yi Zhang, Hui Dong, Hans‐Joachim Krause, Guofeng Zhang, Xiaoming Xie

Published May 29, 2020• 0 citations
Publisher

Abstract

To read out radio frequency (rf) superconducting quantum interference device (SQUID) signals, an rf resonance tank circuit is usually needed. Similar to dc SQUID systems, an rf SQUID system also detects a flux signal that can change slowly over time. In fact, rf SQUID readout electronics exhibit potential advantages over dc SQUID electronics in the direct readout scheme. A merit of rf SQUID systems is the need for just one coaxial cable to connect the readout electronics to the two-terminal element. In a complete magnetometric SQUID system, an input coil connects to a receiver loop (flux antenna) to pick up the measured signals and couples it to the SQUID via a mutual inductance. This chapter discusses the main differences between rf SQUIDs and dc SQUIDs. The significant difference between rf and DC SQUIDs is the occurrence of higher harmonic components in the flux-to-voltage characteristics.

DOI
10.1002/9783527816514.ch12

Related papers

Radio frequency pumped superconducting quantum interference devices with two quantization loops

G.S. Krivoy, H. Koch

Conventional rf SQUIDs (superconducting quantum interference devices) consist of a superconducting loop interrupted by one weak link, and when read out via a tank circuit they produce output signals in the order of a few tens of microvolts. When the single weak link is replaced by a dc SQUID (a superconducting loop with two junctions) a so-called double quantization loop SQUID is formed. In this paper it is shown theoretically, and supported experimentally with thin-film devices of three different designs, that the general behaviour can be explained by a simplified picture of the fixed critical current of the single junction of the rf SQUID being replaced by an effective critical current of a dc SQUID loop that is varied by the applied magnetic flux (i.e., we have a rf SQUID with a variable β parameter). A more detailed analysis of the experimental data and the theory of this novel device reveals its interesting nonlinear character and shows the deviations from this simple picture. It is demonstrated experimentally that output signals in the order of ≥1 mV can be obtained with a suitable read-out mode for the tank circuit, a clear advantage when compared to conventional rf SQUIDs. With respect to dc SQUIDs, the coupling to integrated planar input coils will be unproblematic since no microwave resonances should occur in the structures.

Journal of Applied Physics•Aug 15, 1993•16 citations

Radio frequency bias current scheme for dc superconducting quantum interference device

Y. Zhang, Dongfeng He, N. Wolters +7 more

We have developed a radio frequency bias current scheme with reversal frequency up to 50 MHz for dc superconducting quantum interference devices (SQUIDs). The SQUID and the readout electronics, were connected via a quarter wavelength (/spl lambda//4) transmission line. This transmission line not only transported the SQUID signal, but also served as the resonant matching circuit. For a dc SQUID of inductance 115 pH (loop size 75/spl times/75 /spl mu/m/sup 2/), we measured a flux noise of 33 /spl mu//spl phi//sub 0///spl radic/Hz at 77 K in the flux locked loop configuration. The corner frequency of 1/f noise was less than 0.5 Hz.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•0 citations

Radio frequency SQUIDs operating at 77 K with 1 GHz lumped-element tank circuits

Donghao He, Xian-Lin Zeng, Hans‐Joachim Krause +3 more

We have developed a matching scheme for the operation of a rf superconducting quantum interference device (SQUID) with a lumped-element tank circuit at pumping frequencies up to 1 GHz. This conventional LC resonant circuit is inductively coupled to a matching coil, which is connected to the 50 Ω transmission line. We characterized the flux noise of high-temperature rf SQUIDs at resonant frequencies between 221 and 950 MHz. At about 900 MHz, we obtained the white flux noise of about 14.6 μφ0/Hz with a SQUID inductance LS=150 pH and 20 μφ0/Hz with LS=260 pH. Several of such tank circuits can be driven in parallel or in series with only one cable.

Applied Physics Letters•Feb 23, 1998•36 citations

rf PUMPED SQUID WITH LARGE OUTPUT SIGNAL

G.S. Krivoy, V. A. Komashko

The dc SQUID had been presented for use in the rf SQUID instead of a weak link. The new device, referred to as “double SQUID”, possesses a large output signal (hundreds of microvolts) in operating in a hysteretic mode. For making an operating mode a double SQUID is coupled to a circuit traditional for rf SQUIDs containing a tank circuit and an rf current pumping generator. The magnetic flux being measured is recognized by the dc SQUID quantization loop which results in changing its critical current. As a result the height of the flat part of the tank circuit I–V characteristics coupled to a double SQUID is modulated. It is this modulation that is the SQUID output signal. The experimental investigations of the double SQUID showed the validity of the assumptions under consideration. Output signals up to 690 μV, noise spectral density ≈2×10−5ϕ0/ Hz 1/2 (ϕ0 is the flux quantum) and energy resolution ≈1.4×10−29 J/Hz have been obtained.

Modern Physics Letters B•Feb 28, 1991•5 citations

Flux ramp modulation based MHz frequency-division dc-SQUID multiplexer

Daniel Richter, Ludwig Hoibl, Thomas Wolber +6 more

We present a MHz frequency-division direct-current superconducting quantum interference device (dc-SQUID) multiplexer that is based on flux ramp modulation and a series array of N identical current-sensing dc-SQUIDs with tightly coupled input coil. By running a periodic, sawtooth-shaped current signal through additional modulation coils being tightly but non-uniformly coupled to the individual SQUIDs, the voltage drop across the array changes according to the sum of the flux-to-voltage characteristics of the individual SQUIDs within each cycle of the modulation signal. In this mode of operation, an input signal injected in the input coil of one of the SQUIDs and being quasi-static within a time frame adds a constant flux offset and leads to a phase shift of the associated SQUID characteristics. The latter is proportional to the input signal and can be inferred by channelizing and down-converting the sampled array output voltage. Using a prototype multiplexer as well as custom readout electronics, we demonstrate the simultaneous readout of four signal sources with MHz bandwidth per channel.

arXiv:2101.06424•Applied Physics Letters•Mar 22, 2021•9 citations

Microwave SQUID multiplexer

K. D. Irwin, Konrad W. Lehnert

We describe a superconducting quantum interference device (SQUID) multiplexer operated at microwave frequencies. The outputs of multiple SQUIDs are simultaneously modulated at different frequencies and summed into the input of one high electron mobility transistor (HEMT). The large bandwidth and dynamic range provided by HEMT amplifiers should make it possible to frequency-division multiplex a large number of SQUIDs in one output coaxial cable. We measure low SQUID noise (∼0.5μΦ0∕Hz at 4K) and demonstrate the multiplexed readout of two direct current (dc) SQUIDs at different resonant frequencies. In this work, dc SQUIDs are used, but this approach is equally applicable to radio-frequency SQUIDs.

Applied Physics Letters•Sep 13, 2004•179 citations
To read out radio frequency (rf) superconducting quantum interference device (SQUID) signals, an rf resonance tank circuit is usually needed. Similar to dc SQUID systems, an rf SQUID system also detects a flux signal that can change slowly over time. In fact, rf SQUID readout electronics exhibit potential advantages over dc SQUID electronics in the direct readout scheme. A merit of rf SQUID systems is the need for just one coaxial cable to connect the readout electronics to the two-terminal element. In a complete magnetometric SQUID system, an input coil connects to a receiver loop (flux antenna) to pick up the measured signals and couples it to the SQUID via a mutual inductance. This chapter discusses the main differences between rf SQUIDs and dc SQUIDs. The significant difference between rf and DC SQUIDs is the occurrence of higher harmonic components in the flux-to-voltage characteristics.
Conventional rf SQUIDs (superconducting quantum interference devices) consist of a superconducting loop interrupted by one weak link, and when read out via a tank circuit they produce output signals in the order of a few tens of microvolts. When the single weak link is replaced by a dc SQUID (a superconducting loop with two junctions) a so-called double quantization loop SQUID is formed. In this paper it is shown theoretically, and supported experimentally with thin-film devices of three different designs, that the general behaviour can be explained by a simplified picture of the fixed critical current of the single junction of the rf SQUID being replaced by an effective critical current of a dc SQUID loop that is varied by the applied magnetic flux (i.e., we have a rf SQUID with a variable β parameter). A more detailed analysis of the experimental data and the theory of this novel device reveals its interesting nonlinear character and shows the deviations from this simple picture. It is demonstrated experimentally that output signals in the order of ≥1 mV can be obtained with a suitable read-out mode for the tank circuit, a clear advantage when compared to conventional rf SQUIDs. With respect to dc SQUIDs, the coupling to integrated planar input coils will be unproblematic since no microwave resonances should occur in the structures.
We have developed a radio frequency bias current scheme with reversal frequency up to 50 MHz for dc superconducting quantum interference devices (SQUIDs). The SQUID and the readout electronics, were connected via a quarter wavelength (/spl lambda//4) transmission line. This transmission line not only transported the SQUID signal, but also served as the resonant matching circuit. For a dc SQUID of inductance 115 pH (loop size 75/spl times/75 /spl mu/m/sup 2/), we measured a flux noise of 33 /spl mu//spl phi//sub 0///spl radic/Hz at 77 K in the flux locked loop configuration. The corner frequency of 1/f noise was less than 0.5 Hz.
We have developed a matching scheme for the operation of a rf superconducting quantum interference device (SQUID) with a lumped-element tank circuit at pumping frequencies up to 1 GHz. This conventional LC resonant circuit is inductively coupled to a matching coil, which is connected to the 50 Ω transmission line. We characterized the flux noise of high-temperature rf SQUIDs at resonant frequencies between 221 and 950 MHz. At about 900 MHz, we obtained the white flux noise of about 14.6 μφ0/Hz with a SQUID inductance LS=150 pH and 20 μφ0/Hz with LS=260 pH. Several of such tank circuits can be driven in parallel or in series with only one cable.
The dc SQUID had been presented for use in the rf SQUID instead of a weak link. The new device, referred to as “double SQUID”, possesses a large output signal (hundreds of microvolts) in operating in a hysteretic mode. For making an operating mode a double SQUID is coupled to a circuit traditional for rf SQUIDs containing a tank circuit and an rf current pumping generator. The magnetic flux being measured is recognized by the dc SQUID quantization loop which results in changing its critical current. As a result the height of the flat part of the tank circuit I–V characteristics coupled to a double SQUID is modulated. It is this modulation that is the SQUID output signal. The experimental investigations of the double SQUID showed the validity of the assumptions under consideration. Output signals up to 690 μV, noise spectral density ≈2×10−5ϕ0/ Hz 1/2 (ϕ0 is the flux quantum) and energy resolution ≈1.4×10−29 J/Hz have been obtained.
We present a MHz frequency-division direct-current superconducting quantum interference device (dc-SQUID) multiplexer that is based on flux ramp modulation and a series array of N identical current-sensing dc-SQUIDs with tightly coupled input coil. By running a periodic, sawtooth-shaped current signal through additional modulation coils being tightly but non-uniformly coupled to the individual SQUIDs, the voltage drop across the array changes according to the sum of the flux-to-voltage characteristics of the individual SQUIDs within each cycle of the modulation signal. In this mode of operation, an input signal injected in the input coil of one of the SQUIDs and being quasi-static within a time frame adds a constant flux offset and leads to a phase shift of the associated SQUID characteristics. The latter is proportional to the input signal and can be inferred by channelizing and down-converting the sampled array output voltage. Using a prototype multiplexer as well as custom readout electronics, we demonstrate the simultaneous readout of four signal sources with MHz bandwidth per channel.
We describe a superconducting quantum interference device (SQUID) multiplexer operated at microwave frequencies. The outputs of multiple SQUIDs are simultaneously modulated at different frequencies and summed into the input of one high electron mobility transistor (HEMT). The large bandwidth and dynamic range provided by HEMT amplifiers should make it possible to frequency-division multiplex a large number of SQUIDs in one output coaxial cable. We measure low SQUID noise (∼0.5μΦ0∕Hz at 4K) and demonstrate the multiplexed readout of two direct current (dc) SQUIDs at different resonant frequencies. In this work, dc SQUIDs are used, but this approach is equally applicable to radio-frequency SQUIDs.