Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Applied Physics

Radio frequency pumped superconducting quantum interference devices with two quantization loops

G.S. Krivoy, H. Koch

Published Aug 15, 1993• 16 citations
Publisher

Abstract

Conventional rf SQUIDs (superconducting quantum interference devices) consist of a superconducting loop interrupted by one weak link, and when read out via a tank circuit they produce output signals in the order of a few tens of microvolts. When the single weak link is replaced by a dc SQUID (a superconducting loop with two junctions) a so-called double quantization loop SQUID is formed. In this paper it is shown theoretically, and supported experimentally with thin-film devices of three different designs, that the general behaviour can be explained by a simplified picture of the fixed critical current of the single junction of the rf SQUID being replaced by an effective critical current of a dc SQUID loop that is varied by the applied magnetic flux (i.e., we have a rf SQUID with a variable β parameter). A more detailed analysis of the experimental data and the theory of this novel device reveals its interesting nonlinear character and shows the deviations from this simple picture. It is demonstrated experimentally that output signals in the order of ≥1 mV can be obtained with a suitable read-out mode for the tank circuit, a clear advantage when compared to conventional rf SQUIDs. With respect to dc SQUIDs, the coupling to integrated planar input coils will be unproblematic since no microwave resonances should occur in the structures.

DOI
10.1063/1.354649

Related papers

Theory of signal and noise performance of superconducting quantum interferometers with two quantization loops

Ya. S. Greenberg, G.S. Krivoy, H. Koch

The superconducting quantum interferometer with two quantization loops, the so-called double SQUID, or D-SQUID, is a modification of the well-known rf SQUID. The modification consists of a replacement of the one junction of the rf SQUID by a superconducting loop with two Josephson junctions. This device can be used to transform the weak magnetic flux applied to the loop with junctions to a voltage across the tank circuit inductively coupled to the other loop. As has previously been shown in experiments [G. S. Krivoy and H. Koch, J. Appl. Phys. 74, 2925 (1993)], D-SQUIDs have an extremely large output signal swing up to 1 mV and a transfer function of several mV/(h/2e). In this paper, a D-SQUID theory using a numerical and an analytical approach is developed. The theoretical results are compared with the above-mentioned experiments.

Journal of Applied Physics•May 1, 1995•4 citations

rf PUMPED SQUID WITH LARGE OUTPUT SIGNAL

G.S. Krivoy, V. A. Komashko

The dc SQUID had been presented for use in the rf SQUID instead of a weak link. The new device, referred to as “double SQUID”, possesses a large output signal (hundreds of microvolts) in operating in a hysteretic mode. For making an operating mode a double SQUID is coupled to a circuit traditional for rf SQUIDs containing a tank circuit and an rf current pumping generator. The magnetic flux being measured is recognized by the dc SQUID quantization loop which results in changing its critical current. As a result the height of the flat part of the tank circuit I–V characteristics coupled to a double SQUID is modulated. It is this modulation that is the SQUID output signal. The experimental investigations of the double SQUID showed the validity of the assumptions under consideration. Output signals up to 690 μV, noise spectral density ≈2×10−5ϕ0/ Hz 1/2 (ϕ0 is the flux quantum) and energy resolution ≈1.4×10−29 J/Hz have been obtained.

Modern Physics Letters B•Feb 28, 1991•5 citations

Thin-film resistive SQUIDS

G.S. Krivoy, H. Koch

Different all thin-film partly resistive superconducting quantum interference devices (RSQUIDs) for noise thermometry in the liquid helium temperature range were designed and investigated. Three different types of RSQUID were realised: (i) dc RSQUID, (ii) rf RSQUID, and (iii) RSQUID with two quantization loops (double RSQUID). Shunted tunnel junctions were used as weak links. The resistive parts have been made as a Cu thin film combined with Nb thin films either as a sandwich or a planar element. The devices using a rf pump have integrated rf coupling coils. Resistances of the resistive parts in the range from 2.69 /spl mu//spl Omega/ to 246 /spl mu//spl Omega/ were obtained. The output signal was /spl ap/50 /spl mu/V for the dc RSQUIDs, up to 80 /spl mu/V for the rf RSQUIDs, and up to 1.2 mV for the double RSQUIDs. The linear dependences of the output signal frequency versus a dc current passed through the resistive part were observed up to 40 MHz. The double RSQUIDS described have a clear advantage in the output signal compared to the other RSQUIDs.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•4 citations

Logic Operation Using a High Tc Coupled Superconducting Quantum Interference Device

Kazuo Saitoh, Hiroyuki Fuke, Tadashi Utagawa +1 more

Operation principle of AND/OR logic has been realized in a coupled high-T c Superconducting QUantum Interference Device (SQUID). The device consists of rf- and dc-SQUID's. The logic operation is based on the nonlinear characteristics of the internal and external magnetic flux in the rf-SQUID. Results of the logic operation can be read out by the dc-SQUID. The device is made of NdBa2Cu3O7-δ superconducting thin film with superconducting weak links fabricated using a narrow-focused Ga-ion beam technology.

Japanese Journal of Applied Physics•Nov 1, 1996•4 citations

Superconducting Quantum Interference Devices

J. C. Gallop

In Chapter 2 we made use of a hypothetical arrangement of a strongly coupled superconducting ring, interrupted by a region of weak superconductivity, to derive the essential features of the Josephson effects. In practice this same arrangement is actually employed as the basis of one of the most useful superconducting devices developed so far, the single-junction, or rf, squid . (As mentioned in the Introduction, squid is an acronym for Superconducting QUantum Interference Device.) Here the essential physics behind the operation of these important devices will be described, and in the following section the practical realisation of an rf squid with its associated readout electronics will be explained. Chapter 4 will treat in a similar way dc squid s, which are related devices possessing two weak links in a single ring, whose mode of operation is rather different.

CRC Press eBooks•Oct 19, 2017•5 citations

Proposal for a Beat Oscillating Superconducting Quantum Interference Device

Hisao Furukawa, Shinji Tomiyama, Itsuo Hatono +1 more

We describe a new dc-superconducting quantum interference device (SQUID) circuit of the FM type, which has a large coefficient for converting an applied magnetic flux into a frequency of MHz band or a lower band. The circuit consists of a SQUID amplifier composed of two stages, formed by a superconducting weak link and two dc-SQUID elements with nonhysteretic characteristics. In the first stage, the weak link and dc-SQUID elements are connected in parallel and operated by a common bias voltage. Since the respective elements oscillate with high frequencies by the ac Josephson effect, the two frequencies interact with each other, so that, the first stage generates a beat signal of a lower frequency. In the second stage, the other dc-SQUID element with a intrinsic flux gain enhances the beat signal generated during the first stage. A theoretical analysis of the circuit with computer simulation shows that the beat frequency is a periodical function of the magnetic flux, and the SQUID amplifier with two stages can improve the flux sensitivity.

Japanese Journal of Applied Physics•May 1, 1998•0 citations
Conventional rf SQUIDs (superconducting quantum interference devices) consist of a superconducting loop interrupted by one weak link, and when read out via a tank circuit they produce output signals in the order of a few tens of microvolts. When the single weak link is replaced by a dc SQUID (a superconducting loop with two junctions) a so-called double quantization loop SQUID is formed. In this paper it is shown theoretically, and supported experimentally with thin-film devices of three different designs, that the general behaviour can be explained by a simplified picture of the fixed critical current of the single junction of the rf SQUID being replaced by an effective critical current of a dc SQUID loop that is varied by the applied magnetic flux (i.e., we have a rf SQUID with a variable β parameter). A more detailed analysis of the experimental data and the theory of this novel device reveals its interesting nonlinear character and shows the deviations from this simple picture. It is demonstrated experimentally that output signals in the order of ≥1 mV can be obtained with a suitable read-out mode for the tank circuit, a clear advantage when compared to conventional rf SQUIDs. With respect to dc SQUIDs, the coupling to integrated planar input coils will be unproblematic since no microwave resonances should occur in the structures.
The superconducting quantum interferometer with two quantization loops, the so-called double SQUID, or D-SQUID, is a modification of the well-known rf SQUID. The modification consists of a replacement of the one junction of the rf SQUID by a superconducting loop with two Josephson junctions. This device can be used to transform the weak magnetic flux applied to the loop with junctions to a voltage across the tank circuit inductively coupled to the other loop. As has previously been shown in experiments [G. S. Krivoy and H. Koch, J. Appl. Phys. 74, 2925 (1993)], D-SQUIDs have an extremely large output signal swing up to 1 mV and a transfer function of several mV/(h/2e). In this paper, a D-SQUID theory using a numerical and an analytical approach is developed. The theoretical results are compared with the above-mentioned experiments.
The dc SQUID had been presented for use in the rf SQUID instead of a weak link. The new device, referred to as “double SQUID”, possesses a large output signal (hundreds of microvolts) in operating in a hysteretic mode. For making an operating mode a double SQUID is coupled to a circuit traditional for rf SQUIDs containing a tank circuit and an rf current pumping generator. The magnetic flux being measured is recognized by the dc SQUID quantization loop which results in changing its critical current. As a result the height of the flat part of the tank circuit I–V characteristics coupled to a double SQUID is modulated. It is this modulation that is the SQUID output signal. The experimental investigations of the double SQUID showed the validity of the assumptions under consideration. Output signals up to 690 μV, noise spectral density ≈2×10−5ϕ0/ Hz 1/2 (ϕ0 is the flux quantum) and energy resolution ≈1.4×10−29 J/Hz have been obtained.
Different all thin-film partly resistive superconducting quantum interference devices (RSQUIDs) for noise thermometry in the liquid helium temperature range were designed and investigated. Three different types of RSQUID were realised: (i) dc RSQUID, (ii) rf RSQUID, and (iii) RSQUID with two quantization loops (double RSQUID). Shunted tunnel junctions were used as weak links. The resistive parts have been made as a Cu thin film combined with Nb thin films either as a sandwich or a planar element. The devices using a rf pump have integrated rf coupling coils. Resistances of the resistive parts in the range from 2.69 /spl mu//spl Omega/ to 246 /spl mu//spl Omega/ were obtained. The output signal was /spl ap/50 /spl mu/V for the dc RSQUIDs, up to 80 /spl mu/V for the rf RSQUIDs, and up to 1.2 mV for the double RSQUIDs. The linear dependences of the output signal frequency versus a dc current passed through the resistive part were observed up to 40 MHz. The double RSQUIDS described have a clear advantage in the output signal compared to the other RSQUIDs.>
Operation principle of AND/OR logic has been realized in a coupled high-T c Superconducting QUantum Interference Device (SQUID). The device consists of rf- and dc-SQUID's. The logic operation is based on the nonlinear characteristics of the internal and external magnetic flux in the rf-SQUID. Results of the logic operation can be read out by the dc-SQUID. The device is made of NdBa2Cu3O7-δ superconducting thin film with superconducting weak links fabricated using a narrow-focused Ga-ion beam technology.
In Chapter 2 we made use of a hypothetical arrangement of a strongly coupled superconducting ring, interrupted by a region of weak superconductivity, to derive the essential features of the Josephson effects. In practice this same arrangement is actually employed as the basis of one of the most useful superconducting devices developed so far, the single-junction, or rf, squid . (As mentioned in the Introduction, squid is an acronym for Superconducting QUantum Interference Device.) Here the essential physics behind the operation of these important devices will be described, and in the following section the practical realisation of an rf squid with its associated readout electronics will be explained. Chapter 4 will treat in a similar way dc squid s, which are related devices possessing two weak links in a single ring, whose mode of operation is rather different.
We describe a new dc-superconducting quantum interference device (SQUID) circuit of the FM type, which has a large coefficient for converting an applied magnetic flux into a frequency of MHz band or a lower band. The circuit consists of a SQUID amplifier composed of two stages, formed by a superconducting weak link and two dc-SQUID elements with nonhysteretic characteristics. In the first stage, the weak link and dc-SQUID elements are connected in parallel and operated by a common bias voltage. Since the respective elements oscillate with high frequencies by the ac Josephson effect, the two frequencies interact with each other, so that, the first stage generates a beat signal of a lower frequency. In the second stage, the other dc-SQUID element with a intrinsic flux gain enhances the beat signal generated during the first stage. A theoretical analysis of the circuit with computer simulation shows that the beat frequency is a periodical function of the magnetic flux, and the SQUID amplifier with two stages can improve the flux sensitivity.