Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Mixing of Low Frequency Signals on a Resistive SQUID

Б.В. Васильев, G.S. Krivoy

Published Jan 1, 1977• 0 citations
OpenAlex

Related papers

Improving noise performance of the SQUID in presence of high resistive signal leads

Narayanan Mariyappa, C. Parasakthi, S. Sengottuvel +5 more

AIP conference proceedings•Jan 1, 2012•0 citations

Frequency noise in hysteretic resistive SQUIDs

S.L. Thomasson

Physica B Condensed Matter•Apr 7, 2003•0 citations

SIGNAL AND NOISE CHARACTERISTICS OF RF-SQUIDS

V. I. Shnyrkov, Georgy M. Tsoi

WORLD SCIENTIFIC eBooks•Jun 1, 1992•6 citations

An all thin-film resistive DC SQUID-a current-controlled oscillator

G.S. Krivoy, H. Koch

An all thin-film resistive SQUID with two Josephson tunnel junctions has been designed, fabricated and studied. As well as the two junctions, this device consists of a low ohmic (1.9*10 -6 Omega ) resistive part connected by superconducting leads to both junctions in a loop with very low ( approximately 10 -11 H) inductance. A direct current flowing through the resistive part fixes the voltage difference between the two Josephson junctions that are additionally fed by a bias current. The voltage difference is converted into a signal frequency that can be picked up from the SQUID with a conversion factor of ( phi o ) -1 =483.6 MHz mu V -1 , defined only by the electron charge and Planck's constant. An output signal level (peak-to-peak) of about 50 mu V has been obtained. The low frequency range (below 100 kHz) of the output signal frequency has been investigated. The possibilities of considerably extending this frequency range are also discussed.

Superconductor Science and Technology•Oct 1, 1992•14 citations

The pumpistor: A linearized model of a flux-pumped superconducting quantum interference device for use as a negative-resistance parametric amplifier

K. M. Sundqvist, S. Kintaş, Michaël Simoen +4 more

We describe a circuit model for a flux-driven Superconducting QUantum Interference Device (SQUID). This is useful for developing insight into how these devices perform as active elements in parametric amplifiers. The key concept is that frequency mixing in a flux-pumped SQUID allows for the appearance of an effective negative resistance. In the three-wave, degenerate case treated here, a negative resistance appears only over a certain range of allowed input signal phase. This model readily lends itself to testable predictions of more complicated circuits.

arXiv:1305.7051•Applied Physics Letters•Sep 2, 2013•29 citations

Weak Radio Frequency Signal Reception Sensitivity Based on DC Superconducting Quantum Interference Devices

Shanchi Wu, Chen Gong, Shangbin Li +2 more

Superconducting quantum interference devices (SQUIDs) are promising for detection of extremely weak power regimes for the Internet of Things and long-distance satellite networks. In low-frequency magnetic signal measurements, it has demonstrated superior performance over the traditional systems. We review the resistively and capacitively shunted junction model of dc SQUIDs and investigate its transfer function to magnetic flux signals while taking thermal fluctuation into account. We numerically evaluate the influence of bias current and bias flux signal to determine the operating parameters of the device. The performances related to SQUID ring inductance operating at 4.2 K and 77 K are demonstrated. Combined with common radio frequency front-end modules, including low-noise amplifier and low-pass filter, we evaluate the bit-error-rate performance of the system under different inductance values and inferred that the sensitivity of the system can reach −99 dBm at 100 MHz bandwidth.

IEEE Transactions on Applied Superconductivity•Apr 13, 2023•7 citations
An all thin-film resistive SQUID with two Josephson tunnel junctions has been designed, fabricated and studied. As well as the two junctions, this device consists of a low ohmic (1.9*10 -6 Omega ) resistive part connected by superconducting leads to both junctions in a loop with very low ( approximately 10 -11 H) inductance. A direct current flowing through the resistive part fixes the voltage difference between the two Josephson junctions that are additionally fed by a bias current. The voltage difference is converted into a signal frequency that can be picked up from the SQUID with a conversion factor of ( phi o ) -1 =483.6 MHz mu V -1 , defined only by the electron charge and Planck's constant. An output signal level (peak-to-peak) of about 50 mu V has been obtained. The low frequency range (below 100 kHz) of the output signal frequency has been investigated. The possibilities of considerably extending this frequency range are also discussed.
We describe a circuit model for a flux-driven Superconducting QUantum Interference Device (SQUID). This is useful for developing insight into how these devices perform as active elements in parametric amplifiers. The key concept is that frequency mixing in a flux-pumped SQUID allows for the appearance of an effective negative resistance. In the three-wave, degenerate case treated here, a negative resistance appears only over a certain range of allowed input signal phase. This model readily lends itself to testable predictions of more complicated circuits.
Superconducting quantum interference devices (SQUIDs) are promising for detection of extremely weak power regimes for the Internet of Things and long-distance satellite networks. In low-frequency magnetic signal measurements, it has demonstrated superior performance over the traditional systems. We review the resistively and capacitively shunted junction model of dc SQUIDs and investigate its transfer function to magnetic flux signals while taking thermal fluctuation into account. We numerically evaluate the influence of bias current and bias flux signal to determine the operating parameters of the device. The performances related to SQUID ring inductance operating at 4.2 K and 77 K are demonstrated. Combined with common radio frequency front-end modules, including low-noise amplifier and low-pass filter, we evaluate the bit-error-rate performance of the system under different inductance values and inferred that the sensitivity of the system can reach −99 dBm at 100 MHz bandwidth.