High quality factor bandpass filters based on a number of cascaded resonators of dual-resonance mechanism are proposed in the present paper. Each resonator is constructed as two overlapped coplanar waveguide (CPW) resonant structures. The cascaded resonators mediate microwave coupling between two isolated corner-shaped CPW feeders only at the resonant frequencies leading to a bandpass filter of high quality factor. The two resonant frequencies and the separation between them can be fine-tuned by the dimensions of the structure. The effects of the dimensional parameters of the resonator and the feeding CPW regions on the resonant frequencies and the performance of the bandpass filter are investigated. The effect of the loss tangent of the dielectric substrate material on the quality factors at the two resonant frequencies is studied. Three prototypes of the proposed filter are fabricated and experimentally studied for more understanding of the underlying physical principles of operation and for verifying some of the simulation results. The experimental results show good agreement when compared with the corresponding simulation results. It is shown that, at low enough absolute temperature, the proposed structure can operate as superconducting microwave resonator when made from the appropriate materials. Also, it is shown that an optimized design of the proposed bandpass filter, based on superconducting CPWR structure, can achieve quality factors high enough to form a quantum data bus for hybrid architecture of quantum information systems.
High quality factor bandpass filters based on a number of cascaded resonators of dual-resonance mechanism are proposed in the present paper. Each resonator is constructed as two overlapped coplanar waveguide (CPW) resonant structures. The cascaded resonators mediate microwave coupling between two isolated corner-shaped CPW feeders only at the resonant frequencies leading to a bandpass filter of high quality factor. The two resonant frequencies and the separation between them can be fine-tuned by the dimensions of the structure. The effects of the dimensional parameters of the resonator and the feeding CPW regions on the resonant frequencies and the performance of the bandpass filter are investigated. The effect of the loss tangent of the dielectric substrate material on the quality factors at the two resonant frequencies is studied. Three prototypes of the proposed filter are fabricated and experimentally studied for more understanding of the underlying physical principles of operation and for verifying some of the simulation results. The experimental results show good agreement when compared with the corresponding simulation results. It is shown that, at low enough absolute temperature, the proposed structure can operate as superconducting microwave resonator when made from the appropriate materials. Also, it is shown that an optimized design of the proposed bandpass filter, based on superconducting CPWR structure, can achieve quality factors high enough to form a quantum data bus for hybrid architecture of quantum information systems.
We successfully designed and fabricated an absorption-type of superconducting coplanar waveguide (CPW) resonators. The resonators are made from a niobium film (about 160 nm thick) on a high-resistance Si substrate, and each resonator is fabricated as a meandered quarter-wavelength transmission line (one end is short to the ground and another end is capacitively coupled to a through feedline). With a vector network analyzer we measured the transmissions of the applied microwave through the resonators at ultra-low temperature. The obtained loaded quality factors are significantly high, i.e. up to ∼10 6 . When the temperature increases slowly from the base temperature (20 mK), the resonance frequencies of the resonators are blue shifted and the quality factors are lowered slightly. In principle, this type of device can integrate a series of CPW resonators with a common feedline, making it a promising candidate as the data bus for coupling distant solid-state qubits and the sensitive detector of single photons.
Superconducting coplanar-waveguide (CPW) resonators are one of the key devices in circuit quantum electrodynamics (cQED). Their performance can be limited by dielectric losses in the substrate and in the material interfaces. Reliable modeling is required to aid in the design of low-loss CPW structures for cQED. We analyze the geometric dependence of the dielectric losses in CPW structures using finite-element modeling of the participation ratios of the lossy regions. In a practical scenario, uncertainties in the the dielectric constants and loss tangents of these regions introduce uncertainties in the theoretically predicted participation ratios. We present a method for combining loss simulations with measurements of two-level-system-limited quality factors and resonance frequencies of CPW resonators. Namely, we solve an inverse problem to find model parameters producing the measured values. High quality factors are obtainable by properly designing the cross-sectional geometries of the CPW structures, but more accurate modeling and design methods for low-loss CPW resonators are called for major future improvements. Our nonlinear optimization methodology for solving the aforementioned inverse problem is a step in this direction.
Superconducting coplanar waveguide (SCPW) resonators have a wide range of applications due to the combination of their planar geometry and high quality factors relative to normal metals. However, their performance is sensitive to both the details of their geometry and the materials and processes that are used in their fabrication. In this paper, we study the dependence of SCPW resonator performance on materials and geometry as a function of temperature and excitation power. We measure quality factors greater than 2 × 106 at high excitation power and 6 × 105 at a power comparable to that generated by a single microwave photon circulating in the resonator. We examine the limits to the high excitation power performance of the resonators and find it to be consistent with a model of radiation loss. We further observe that while in all cases the quality factors are degraded as the temperature and power are reduced due to dielectric loss, the size of this effect is dependent on resonator materials and geometry. Finally, we demonstrate that the dielectric loss can be controlled in principle using a separate excitation near the resonance frequencies of the resonator.
In this master's thesis, I present the design, fabrication, and characterisation of superconducting microwave resonators. These resonators are quarter-wavelength coplanar waveguide resonators, operating at resonance frequencies between 4 GHz and 8 GHz. This kind of resonator is a key component in several applications, ranging from quantum computation devices to parametric amplifiers. Minimising the losses (achieving high internal quality factors) in these resonators is important to maximise performance of the applications they are used for. During the thesis work, we have studied several possible changes to improve the resonator quality.\n\nFabrication of the resonators was done in the Nanofabrication Laboratory at Chalmers University of Technology, and consist of the following steps: cleaning a sapphire or silicon wafer, depositing a layer of superconducting niobium, photolithography, and etching the waveguide. We then measured the resonators in a cryogen-free dilution refrigerator, at a temperature of 10 mK. The measurements consisted of a power sweep, in order to quantify the quality factor at high and low excitation powers. As an example, the first resonator we fabricated had a quality factor of 4.3 x 10^4 at high power (about 10^5 photons in the resonator), and quality factor of 3.7 x 10^4 at the single-photon level.\n\nWe then investigated different loss mechanisms that we expect to negatively affect the quality factor, and how to reduce this loss. Firstly, to reduce radiation losses and magnetic vortex losses, we reduced the lateral dimensions of the resonator. Secondly, as two-level system (TLS) losses are believed to mainly reside at the surfaces of the materials and interfaces between them, we etched into the substrate to selectively move a part of the TLS away from the resonator. We also studied the effect of the meandering of the resonator on the quality factor, as well as using two different etching gasses.\n\nBy gathering all this data, we were then able to compare the different combinations to see the effect of the changing parameters. In conclusion, the reduced lateral dimensions and the removal of part of the substrate indeed reduce the losses, as expected from the theory. We also found interesting behaviour with regards to the meandering, namely that having a meandered structure negatively affects the quality factor.\n\nCombining all results, we can give a guideline for the fabrication of resonators in the future, which gave us a quality factor up to 4.9 x 10^5 at high excitation power, and 3.0 x 10^5 at the single photon level.
In this paper, we present a novel design of a compact, double-fold half-wave superconducting coplanar waveguide resonator, specifically optimized for quantum readout. The geometry offers advantages in terms of scalability and allows for a more compact integration of qubits per unit area. The superconducting resonators are designed to operate within a fundamental frequency range of 1.9 GHz$-1.95GHz,utilizingbothgapandfingercouplingschemes.Thedevicesarefabricatedusingthinaluminumfilmsdepositedonhigh−resistivitysapphiresubstrates.Theproposedresonatorsexhibitqualityfactor(Q_{L})of2.9× 10^{5}$and 1.58 ×103for gap coupled and finger coupled, respectively, during experimental measurements. The simulated QLof single-folded meander line resonators are found to be 4.65 ×105and 258.42, for gap coupled and finger coupled, respectively, for comparison purpose at similar operating frequency. A comprehensive analysis of the microwave transmission spectra was conducted at cryogenic temperatures near 10 mK, across very high input drive powers ($-30dBmto-10dBm).Experimentalresultsshowagoodagreementwithsimulationsandtheequivalentlumpedcircuitmodel.Notably,theproposeddesignreducesthephysicalfootprintoftheresonatordevicesupto28.2\%comparedtoconventionalsingle−foldmeanderedstructures.TheresonatorsdemonstratestrongpotentialforintegratingqubitswithreadoutandcontrolbusesinquantuminformationprocessingwhichrequireaQ_{L}$between104−105. They also being well-suited for cryogenic detector applications that utilize microwave kinetic inductance detector (MKID) arrays in frequency multiplexing for different coupling schemes.
Superconducting quantum computing systems, including coplanar waveguide (CPW) resonators and qubits, are highly susceptible to energy dissipation from two-level systems (TLS) within bulk and interfacial dielectrics. CPW resonators serve as an ideal platform for characterizing these material losses at the single-photon excitation level. Building on recent experimental evidence that interface engineering can mitigate TLS losses, this study employs simulations to evaluate resonator quality factors across various interface modifications. Our results demonstrate that reducing losses at the substrate–air (SA) interface can increase the internal quality factor Qi by up to three orders of magnitude. While etching the SA interface also enhances Qi, material loss remains the dominant dissipation mechanism. Furthermore, we find that other lossy interfaces have a significantly smaller impact on the quality factor compared to the SA interface. These simulation results align with established experimental findings, providing a robust framework for refining resonator design. This work offers precise guidelines for TLS mitigation, essential for enhancing coherence times and developing more reliable superconducting quantum processors.