Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Institute of Physics eBooks

Quantum latches and counter circuits

Hafiz Md. Hasan Babu

Published May 1, 2020• 0 citations
Publisher
DOI
10.1088/978-0-7503-2747-3ch12

Related papers

Design and demonstration of fundamental logic circuits based on a single-flux-quantum gate with a resettable latch

Naoki Takeuchi, A. Akahori, N. Mori +4 more

We have confirmed the importance of the tolerance design for obtaining correct operation in larger-scale Single Flux Quantum (SFQ) logic circuit. Experimental results show that the bias margin of SFQ/dc converter is considerably enhanced by employing tolerance design. The primitives of Single-Flux-Quantum-logic with Ressettable Latch (SFQ-RL) are designed to have high tolerance. As a result, relatively complex circuits based on SFQ-RL including 4-bit Shift Register, 3-Input Majority circuits, binary counter operate correctly with sufficient bias margins. These circuits are fabricated in NEC's standard process using 2.5 kA/cm/sup 2/ Nb/AlOx/Nb junction technology.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•0 citations

Quantum Circuits

Colin P. Williams

Texts in computer science•Dec 6, 2010•1 citation

Time-to-digital converters based on RSFQ digital counters

Oleg A. Mukhanov, Sergey V. Rylov

We have designed, fabricated, and successfully tested a Time-to-Digital converter (TDC). The TDC circuit consists of superconductive counters based on toggle flip-flops with destructive readout, shift registers, parallel-to-serial converters, and pulse detectors. The value of the counter is latched while the counter is operating at full speed. The TDC resolution is directly determined by the maximum counter speed, or 50 ps for an available 20 GHz clock rate. The circuits are implemented in HYPRES' standard Nb process with a critical current density of 1.0 kA/cm/sup 2/ using HYPRES' library of standard RSFQ cells.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•24 citations

Quantum circuits

Dipankar Bhattacharyya, Jyotirmoy Guha

Institute of Physics eBooks•Jan 1, 2022•0 citations

Quantum Circuits

WORLD SCIENTIFIC eBooks•Aug 27, 2026•0 citations

A high-temperature superconductor latching driver operated at 30 K for a single-flux-quantum/semiconductor interface

Tsunehiro Hato, Masahiro Horibe, Naoki Harada +5 more

We report on a latching-type driver operated at 30 K for the output interface of single-flux-quantum (SFQ) circuits. Ramp-edge-type high-temperature superconductor (HTS) junctions showed only small inherent hysteresis in current–voltage characteristics at a temperature of 30 K. To have hysteresis large enough for latching operation, we chose La-doped YbBaCuO as a counter electrode of an interface modified junction, and used amorphous LaSrAlTaO to form an additional barrier to the interface modified barrier. The junction shunted with optimized capacitance showed sufficiently large hysteresis of 33%, which is as large as that of a non-shunted junction at 4.2 K. We employed 20 kA cm−2 as the critical current density (Jc) of the junction to fabricate dc/SFQ, Josephson transmission lines (JTLs) and the latching driver on the same chip. It is smaller than the optimum current density that gives the smallest punchthrough probability of the junction, which was calculated to be 10−12 for a 30 Gbps ac bias by using the junction parameters at 30 K. However, the probability for Jc of 20 kA cm−2 is still smaller than that of low-temperature semiconductor junctions because of the larger Jc of the HTS junctions. The fabricated latching driver successfully converted the SFQ pulse, which passed through several JTLs from the dc/SFQ circuit, to a 1 mV level signal at 30 K.

Superconductor Science and Technology•Nov 7, 2003•3 citations
We have confirmed the importance of the tolerance design for obtaining correct operation in larger-scale Single Flux Quantum (SFQ) logic circuit. Experimental results show that the bias margin of SFQ/dc converter is considerably enhanced by employing tolerance design. The primitives of Single-Flux-Quantum-logic with Ressettable Latch (SFQ-RL) are designed to have high tolerance. As a result, relatively complex circuits based on SFQ-RL including 4-bit Shift Register, 3-Input Majority circuits, binary counter operate correctly with sufficient bias margins. These circuits are fabricated in NEC's standard process using 2.5 kA/cm/sup 2/ Nb/AlOx/Nb junction technology.
We have designed, fabricated, and successfully tested a Time-to-Digital converter (TDC). The TDC circuit consists of superconductive counters based on toggle flip-flops with destructive readout, shift registers, parallel-to-serial converters, and pulse detectors. The value of the counter is latched while the counter is operating at full speed. The TDC resolution is directly determined by the maximum counter speed, or 50 ps for an available 20 GHz clock rate. The circuits are implemented in HYPRES' standard Nb process with a critical current density of 1.0 kA/cm/sup 2/ using HYPRES' library of standard RSFQ cells.
We report on a latching-type driver operated at 30 K for the output interface of single-flux-quantum (SFQ) circuits. Ramp-edge-type high-temperature superconductor (HTS) junctions showed only small inherent hysteresis in current–voltage characteristics at a temperature of 30 K. To have hysteresis large enough for latching operation, we chose La-doped YbBaCuO as a counter electrode of an interface modified junction, and used amorphous LaSrAlTaO to form an additional barrier to the interface modified barrier. The junction shunted with optimized capacitance showed sufficiently large hysteresis of 33%, which is as large as that of a non-shunted junction at 4.2 K. We employed 20 kA cm−2 as the critical current density (Jc) of the junction to fabricate dc/SFQ, Josephson transmission lines (JTLs) and the latching driver on the same chip. It is smaller than the optimum current density that gives the smallest punchthrough probability of the junction, which was calculated to be 10−12 for a 30 Gbps ac bias by using the junction parameters at 30 K. However, the probability for Jc of 20 kA cm−2 is still smaller than that of low-temperature semiconductor junctions because of the larger Jc of the HTS junctions. The fabricated latching driver successfully converted the SFQ pulse, which passed through several JTLs from the dc/SFQ circuit, to a 1 mV level signal at 30 K.