We report on the recent improvements of the mercury optical lattice clock based on199Hg operating at LNESYRTE. In particular we describe how the exploitation of a 2D Magneto Optical Trap (2D-MOT) allowed us to increase significantly the number of useful atoms gathered in a given time. As a consequence we were able to decrease the loading time of the mercury optical lattice clock, so as the cycle time, that is the main factor of the Dick effect.
We report on the recent improvements of the mercury optical lattice clock based on199Hg operating at LNESYRTE. In particular we describe how the exploitation of a 2D Magneto Optical Trap (2D-MOT) allowed us to increase significantly the number of useful atoms gathered in a given time. As a consequence we were able to decrease the loading time of the mercury optical lattice clock, so as the cycle time, that is the main factor of the Dick effect.
Two-dimensional magneto-optical trapping (2D-MOT) is an efficient tool for generating a high flux of precooled atoms. A 2D-MOT for mercury (Hg) is so far missing despite the potential of this atomic species in several areas. Here, we present the characterization of a 2D-MOT for Hg enabled by addressing the 1S0- 3P1 laser cooling transition at 254 nm. The laser source based on an ytterbium-doped fiber amplifier has low-frequency noise and high reliability. Parameters affecting the efficiency of the 2D-MOT are studied, i.e., optical trapping power, push beam power, cooling laser frequency detuning, and magnetic-field gradient. When used with a Hg optical lattice clock, the 2D-MOT increases by a factor of 4.5, the rate of preparation of the atomic samples, yielding an improved clock short term stability of $6.4\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}16}$ at 1 s.
A cold atom source is important for quantum metrology and precision measurement. To reduce the quantum projection noise limit in optical lattice clock, one can increase the number of cold atoms and reduce the dead time by enhancing the loading rate. In this work, we realize an enhanced cold mercury atom source based on a two-dimensional (2D) magneto-optical trap (MOT). The vacuum system is composed of two titanium chambers connected with a differential pumping tube. Two stable cooling laser systems are adopted for the 2D-MOT and the three-dimensional (3D)-MOT, respectively. Using an optimized 2D-MOT and push beam, about 1.3×106 atoms, which are almost an order of magnitude higher than using a pure 3D-MOT, are loaded into the 3D-MOT for 202Hg atoms. This enhanced cold mercury atom source is helpful in increasing the frequency stability of a neutral mercury lattice clock.
To realize a neutral mercury lattice clock, an experimental setup is in developing in SIOM. With two stable cooling lasers and a new vacuum system, an enhanced cold mercury atom source is implemented based on a two-dimensional magneto-optical trap (2D-MOT). By applying a hybrid frequency stabilization method and optimization of the 2D-MOT, about 1.3×106cold mercury atoms are obtained with a loading rate of 1.0×106atoms/s. And a high power injection-locked Ti:sapphire laser at 725 nm is developed for optical lattice at magic-wavelength.
Efficient preparation of cold atoms plays an important role in realizing precision measurement including optical lattice clocks (OLCs). Fast preparation of cold atoms reduces Dick noise by shortening dead time in a clock interrogation cycle, which improves the stability of OLCs. Here, we increase the loading rate of the three-dimensional magneto-optical trap (3D-MOT) in the ultra-high vacuum environment by utilizing the two-dimensional magneto-optical trap (2D-MOT) with a push beam, reduce the temperature of cold atoms with the compression-MOT technique which is implemented by reducing the detuning of 3D-MOT rapidly at the end of atom preparation, and realize the enhanced production of cold atoms for 199Hg OLCs. To achieve 3D-MOT and 2D-MOT of mercury atoms, a deep ultraviolet laser (DUVL) system composed of three DUVLs is developed with one working in lower power for frequency locking and the other two in high power for laser cooling. Such a configuration improves the long-term frequency stability and shows greater robustness than our previous system consisting of two DUVLs. To maximize the 3D-MOT loading rate, we orderly optimize the detuning and the magnetic field gradient of 3D-MOT and those of 2D-MOT as well as the detuning and the power of the push beam. After all parameters are optimized, we measure the maximum loading rate of 3D-MOT to be 3.1×105 s–1 and prepare cold atoms of 1.8×106 in 9 s. The loading rate is greatly enhanced by a factor of 51 by using 2D-MOT and the push beam. In order to improve the efficiency of transferring cold atoms from 3D-MOT to optical lattice, we use compression-MOT technique to reduce the temperature of cold atoms and produce cold 199Hg atoms which are about 45 μK, lower than the expected temperature of Doppler cooling theory. By achieving the high gain of the 3D-MOT loading rate under the ultra-high vacuum and reducing the temperature of cold atoms, this enhanced preparation of cold atoms based on 2D-MOT effectively shortens the preparation time of cold atoms and improves the transfer efficiency of optical lattice, which provides a significant scheme for efficiently preparing cold mercury atoms in other experiments.
Optics lattice clock is a hot topic in the researches of frequency standard and metrology. Neutral mercury atom is one of the most promising candidates for optical lattice clock. Due to its large atomic number, mercury atom is insensitive to black body radiation, which is the severe limitation for developing the optical lattice clocks. To realize the optical lattice clock of neutral mercury atoms, the first step is to implement laser-cooling and trapping of neutral mercury atoms. The cooling transition of mercury atom is 1S0-3P1 transition. The wavelength is 253.7 nm, the line width is 1.27 MHz, and the saturation intensity is 10.2 mW/cm2. Quantum projection noise (QPN) is an important parameter that affects optical lattice clock. Increasing the loading rate of magneto-optical trap (MOT) can help lower the QPN, thereby improving the performance of optical lattice clock. In this work, we calculate the scattering force of deep UV cooling laser, which is exerted on mercury atom in our single chamber MOT, and numerically simulate the one-dimensional motion of the atom in the MOT. It gives us the capture velocity under optimized parameters of the MOT. Then we calculate the loading rate of three-dimensional MOT by a high efficient random sampling method. According to the rate equation of MOT, the loading rate is proportional to the atom number of the steady state, which is the accessible parameter in the experiment. An experimental setup of MOT is established with a high vacuum system and a frequency quadrupled semiconductor laser system. The fluorescence imaging on an EMCCD gives the atom number in the MOT. We also calibrate the vapor density of background mercury gas in the vacuum, and measure the atom number in a steady MOT. We numerically simulate and experimentally study the influences on the atom number on the parameters of MOT, such as laser intensity, laser detuning and magnetic field gradient. The calculated results are in consistent with the experimental results. We also find the optimized parameters to maximize the loading rate. The numerical simulation also gives some results beyond current experimental condition, especially for laser intensity. From the simulations we obtain the optimized MOT parameter and relation for laser cooling of neutral mercury atom. Especially, current deep UV cooling laser with 20 mW of power does not have enough power to enhance the loading rate. These results are rather valuable for designing the next generation of optical lattice clocks for neutral mercury atoms.
We describe our work to develop an optical lattice clock using neutral mercury, which has the potential to reach accuracy near 1 part in 1018owing to its low sensitivity to black body radiation. We describe developments of our experimental setup to allow dipole lattice trapping and spectroscopy in the Lamb-Dicke regime. Specifically, we report on the implementation of a low noise imaging and detection system, on the characterization of the magneto-optic trap from which the dipole trap will be loaded, on the implementation of the dipole lattice trap itself, a challenging task given the wavelength and power requirements.