Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Chinese Physics B

Nb-based Josephson parametric amplifier for superconducting qubit measurement*

Feifan Su, Ziting Wang, Huikai Xu, Shoukuan Zhao, Yan Hai-sheng, Zhaohua Yang, Ye F. Tian, Shi-Ping Zhao

Published Sep 18, 2019• 10 citations
Publisher

Abstract

We report a fabrication process and characterization of the Josephson parametric amplifier (JPA) for the single-shot quantum state measurement of superconducting multiqubit system. The device is prepared using Nb film as its base layer, which is convenient in the sample patterning process like e-beam lithography and film etching. Our results show that the JPA has a bandwidth up to 600 MHz with gain above 15 dB and noise temperature approaching the quantum limit. The qubit state differentiation measurements demonstrate the signal-to-noise ratio around 3 and the readout fidelity above 97% and 91% for the ground and first-excited states, respectively.

DOI
10.1088/1674-1056/ab4578

Related papers

Fabrication and characterization of all-Nb lumped-element Josephson parametric amplifiers*

Hang Xue, Zhirong Lin, Wenbing Jiang +4 more

Josephson parametric amplifiers (JPAs) with nearly quantum-limited noise performance have become indispensable devices for the measurements of superconducting quantum information. We have developed an all-Nb lumped-element flux-driven JPA operating in the three-wave mixing mode. Our Nb-based JPA comprises Nb/Al-AlO x /Nb Josephson junctions, a parallel-plate capacitor with SiO2 dielectric sandwiched between two Nb layers, a bottom coplanar waveguides layer, and a top Nb wiring layer. We experimentally demonstrate a 20 dB gain over a 190 MHz bandwidth, a mean 1 dB compression of –123 dBm, and near quantum-limited noise performance. This fabrication process can be further used to design impedance transformed parametric amplifiers for multiple-qubit readout.

Chinese Physics B•Mar 16, 2021•4 citations

Development and characterization of a flux-pumped lumped element Josephson parametric amplifier

Martina Esposito, Joseph Rahamim, Andrew Patterson +11 more

Josephson parametric amplification is a tool of paramount importance in circuit-QED especially for the quantum-noise-limited single-shot read-out of superconducting qubits. We developed a Josephson parametric amplifier (JPA) based on a lumped-element LC resonator, in which the inductance L is composed by a geometric inductance and an array of 4 superconducting quantum interference devices (SQUIDs). We characterized the main figures of merit of the device, obtaining a −3 dB bandwidth BW = 15 MHz for a gain G = 21 dB and a 1 dB compression point P1dB = −115 dBm. The obtained results are promising for the future use of such JPA as the first stage of amplification for single-shot readout of superconducting qubits.

EPJ Web of Conferences•Jan 1, 2019•4 citations

Fabrication of Josephson parameter amplifier and its application in squeezing vacuum fluctuations*

Pengtao Song, Xueyi Guo, Kai Xu +7 more

Josephson parameter amplifier (JPA) is a microwave signal amplifier device with near-quantum-limit-noise performance. It has important applications in scientific research fields such as quantum computing and dark matter detection. This work reports the fabrication and characterization of broadband JPA devices and their applications in multi-qubit readout and squeezing of vacuum state. We use a process in which transmission lines and electrodes are made of niobium thin film and aluminum Josephson junctions are made by Dolan bridge technique. We believe this process is more convenient than the process we used previously. The whole production process adopts electron beam lithography technology to ensure high structural resolution. The test result shows that the gain value of the manufactured JPA can exceed 15 dB, and the amplification bandwidth is about 400 MHz. The noise temperature is about 400 mK at the working frequency of 6.2 GHz. The devices have been successfully used in experiments involving superconducting multi-qubit quantum processors. Furthermore, the device is applied to squeeze vacuum fluctuations and a squeezing level of 1.635 dB is achieved.

Chinese Physics B•Jun 3, 2021•1 citation

Quantum Noise Limited Nondegenerate Josephson Parametric Amplifier with Nb/AlOx/Nb Junctions for Qubit Readout

Ilya S. Besedin, I. Pologov, Lyudmila V. Filippenko +2 more

Abstract Over the last two decades, the superconducting qubits have become a promising and rapidly growing area of research. However, there are specific challenges when working with such a delicate system. One of them is the qubit state readout. Since a very small signal (of the order of 1 photon) is used for the readout, its detection is challenging and it requires low-noise cryogenic amplifiers working in the 3–12 GHz frequency range. Josephson parametric amplifiers (JPAs) are one of the most studied and developed candidates. Currently, several JPA designs offer low noise performance and instantaneous bandwidth from tens of MHz to several GHz; they are also becoming an integral part of circuit quantum electrodynamics (cQED) setups. In the current work, results are presented of the measurements of a JPA made of a coplanar waveguide with an array of three SQUIDs. Nondegenerate amplification and an amplifier added noise being close to the quantum limit are demonstrated.

Instruments and Experimental Techniques•Oct 1, 2024•0 citations

Flux-pumped impedance-engineered broadband Josephson parametric amplifier

Joel Grebel, Audrey Bienfait, Étienne Dumur +7 more

Broadband quantum-limited amplifiers play a critical role in the single-shot readout of superconducting qubits, but a popular implementation, the traveling wave parametric amplifier, involves a complex design and fabrication process. Here, we present a simple design for a Josephson parametric amplifier, using a lumped element resonator comprising a superconducting quantum interference device whose useful bandwidth is enhanced with an on-chip impedance-matching circuit. We demonstrate a flux-coupling geometry that maximizes the coupling to the Josephson loop and minimizes spurious excitation of the amplifier resonant circuit. The amplifier, which operates in a flux-pumped mode, is demonstrated with a power gain of more than 20 dB over a bandwidth of about 300 MHz, where approximate noise measurements indicate quantum-limited performance. A procedure is given for optimizing the bandwidth for this kind of amplifier, using a linearized circuit simulation while minimizing non-linearities.

Applied Physics Letters•Apr 5, 2021•53 citations

Parametric amplification in a Josephson junction array Fabry-Pérot cavity

Javier Navarro Montilla, Nikita S. Klimovich, A. Barbier +2 more

Abstract Superconducting Parametric Amplifiers (SPAs) with near-quantum-limited added noise are crucial for weak signal detection applications such as astronomical receivers, quantum computation, and fundamental physics experiments. Commercially available SPAs include Josephson Parametric Amplifiers (JPAs), which offer high gain but narrow bandwidth performance; and Josephson-junction Travelling Wave Parametric Amplifiers (JTWPAs), which provide broader bandwidth at the cost of a complicated fabrication procedure, lower fabrication yield, and larger footprint area. In this paper, we investigate the parametric amplification of microwave signals in a Josephson array embedded in a low-Q Fabry-Pérot cavity. We fabricated a 500-junction array device and measured >15 dB phase-preserving gain over a ∼350 MHz bandwidth, while offering almost two orders of magnitude improvement in compression point (P 1dB = −106.2 dBm) compared to standard JPAs. Furthermore, using a novel measurement technique, we configured our device to operate in the phase-sensitive mode, measuring a phase-sensitive extinction ratio (PSER) of 42.3 ± 2.81 dB, in line with state-of-the-art values for JPAs. These promising performances, combined with the ease of fabrication and improved yield compared with JTWPAs, underscore the potential of these devices for applications in advanced detection schemes.

Physica Scripta•Sep 1, 2025•1 citation
We report a fabrication process and characterization of the Josephson parametric amplifier (JPA) for the single-shot quantum state measurement of superconducting multiqubit system. The device is prepared using Nb film as its base layer, which is convenient in the sample patterning process like e-beam lithography and film etching. Our results show that the JPA has a bandwidth up to 600 MHz with gain above 15 dB and noise temperature approaching the quantum limit. The qubit state differentiation measurements demonstrate the signal-to-noise ratio around 3 and the readout fidelity above 97% and 91% for the ground and first-excited states, respectively.
Josephson parametric amplifiers (JPAs) with nearly quantum-limited noise performance have become indispensable devices for the measurements of superconducting quantum information. We have developed an all-Nb lumped-element flux-driven JPA operating in the three-wave mixing mode. Our Nb-based JPA comprises Nb/Al-AlO x /Nb Josephson junctions, a parallel-plate capacitor with SiO2 dielectric sandwiched between two Nb layers, a bottom coplanar waveguides layer, and a top Nb wiring layer. We experimentally demonstrate a 20 dB gain over a 190 MHz bandwidth, a mean 1 dB compression of –123 dBm, and near quantum-limited noise performance. This fabrication process can be further used to design impedance transformed parametric amplifiers for multiple-qubit readout.
Josephson parametric amplification is a tool of paramount importance in circuit-QED especially for the quantum-noise-limited single-shot read-out of superconducting qubits. We developed a Josephson parametric amplifier (JPA) based on a lumped-element LC resonator, in which the inductance L is composed by a geometric inductance and an array of 4 superconducting quantum interference devices (SQUIDs). We characterized the main figures of merit of the device, obtaining a −3 dB bandwidth BW = 15 MHz for a gain G = 21 dB and a 1 dB compression point P1dB = −115 dBm. The obtained results are promising for the future use of such JPA as the first stage of amplification for single-shot readout of superconducting qubits.
Josephson parameter amplifier (JPA) is a microwave signal amplifier device with near-quantum-limit-noise performance. It has important applications in scientific research fields such as quantum computing and dark matter detection. This work reports the fabrication and characterization of broadband JPA devices and their applications in multi-qubit readout and squeezing of vacuum state. We use a process in which transmission lines and electrodes are made of niobium thin film and aluminum Josephson junctions are made by Dolan bridge technique. We believe this process is more convenient than the process we used previously. The whole production process adopts electron beam lithography technology to ensure high structural resolution. The test result shows that the gain value of the manufactured JPA can exceed 15 dB, and the amplification bandwidth is about 400 MHz. The noise temperature is about 400 mK at the working frequency of 6.2 GHz. The devices have been successfully used in experiments involving superconducting multi-qubit quantum processors. Furthermore, the device is applied to squeeze vacuum fluctuations and a squeezing level of 1.635 dB is achieved.
Abstract Over the last two decades, the superconducting qubits have become a promising and rapidly growing area of research. However, there are specific challenges when working with such a delicate system. One of them is the qubit state readout. Since a very small signal (of the order of 1 photon) is used for the readout, its detection is challenging and it requires low-noise cryogenic amplifiers working in the 3–12 GHz frequency range. Josephson parametric amplifiers (JPAs) are one of the most studied and developed candidates. Currently, several JPA designs offer low noise performance and instantaneous bandwidth from tens of MHz to several GHz; they are also becoming an integral part of circuit quantum electrodynamics (cQED) setups. In the current work, results are presented of the measurements of a JPA made of a coplanar waveguide with an array of three SQUIDs. Nondegenerate amplification and an amplifier added noise being close to the quantum limit are demonstrated.
Broadband quantum-limited amplifiers play a critical role in the single-shot readout of superconducting qubits, but a popular implementation, the traveling wave parametric amplifier, involves a complex design and fabrication process. Here, we present a simple design for a Josephson parametric amplifier, using a lumped element resonator comprising a superconducting quantum interference device whose useful bandwidth is enhanced with an on-chip impedance-matching circuit. We demonstrate a flux-coupling geometry that maximizes the coupling to the Josephson loop and minimizes spurious excitation of the amplifier resonant circuit. The amplifier, which operates in a flux-pumped mode, is demonstrated with a power gain of more than 20 dB over a bandwidth of about 300 MHz, where approximate noise measurements indicate quantum-limited performance. A procedure is given for optimizing the bandwidth for this kind of amplifier, using a linearized circuit simulation while minimizing non-linearities.
Abstract Superconducting Parametric Amplifiers (SPAs) with near-quantum-limited added noise are crucial for weak signal detection applications such as astronomical receivers, quantum computation, and fundamental physics experiments. Commercially available SPAs include Josephson Parametric Amplifiers (JPAs), which offer high gain but narrow bandwidth performance; and Josephson-junction Travelling Wave Parametric Amplifiers (JTWPAs), which provide broader bandwidth at the cost of a complicated fabrication procedure, lower fabrication yield, and larger footprint area. In this paper, we investigate the parametric amplification of microwave signals in a Josephson array embedded in a low-Q Fabry-Pérot cavity. We fabricated a 500-junction array device and measured >15 dB phase-preserving gain over a ∼350 MHz bandwidth, while offering almost two orders of magnitude improvement in compression point (P 1dB = −106.2 dBm) compared to standard JPAs. Furthermore, using a novel measurement technique, we configured our device to operate in the phase-sensitive mode, measuring a phase-sensitive extinction ratio (PSER) of 42.3 ± 2.81 dB, in line with state-of-the-art values for JPAs. These promising performances, combined with the ease of fabrication and improved yield compared with JTWPAs, underscore the potential of these devices for applications in advanced detection schemes.