Adiabatic quantum-flux-parametron (AQFP) logic is an energy-efficient superconductor logic family. The switching energy of an AQFP gate can be arbitrarily reduced via adiabatic switching. However, AQFP logic has somewhat long latency due to the multiphase clocking scheme, in which each logic operation requires a quarter clock cycle. The latency in AQFP logic should be improved in order to design complex digital circuits such as microprocessors. In the present paper, we propose a low-latency clocking scheme for AQFP logic, which we call delay-line clocking. In delay-line clocking, the latency for each logic operation is determined by the propagation delay of the excitation current, which can be much shorter than a quarter clock cycle. Our numerical simulation shows that AQFP gates can operate with a latency of only a few picoseconds. We fabricated an AQFP circuit adopting delay-line clocking using the 10 kA/cm2 Nb high-speed standard process provided by the National Institute of Advanced Industrial Science and Technology. The circuit was demonstrated at 4 GHz with a latency of 10 ps per gate. The above results indicate that delay-line clocking can significantly reduce the latency in AQFP logic.
Adiabatic quantum-flux-parametron (AQFP) logic is an energy-efficient superconductor logic family. The switching energy of an AQFP gate can be arbitrarily reduced via adiabatic switching. However, AQFP logic has somewhat long latency due to the multiphase clocking scheme, in which each logic operation requires a quarter clock cycle. The latency in AQFP logic should be improved in order to design complex digital circuits such as microprocessors. In the present paper, we propose a low-latency clocking scheme for AQFP logic, which we call delay-line clocking. In delay-line clocking, the latency for each logic operation is determined by the propagation delay of the excitation current, which can be much shorter than a quarter clock cycle. Our numerical simulation shows that AQFP gates can operate with a latency of only a few picoseconds. We fabricated an AQFP circuit adopting delay-line clocking using the 10 kA/cm2 Nb high-speed standard process provided by the National Institute of Advanced Industrial Science and Technology. The circuit was demonstrated at 4 GHz with a latency of 10 ps per gate. The above results indicate that delay-line clocking can significantly reduce the latency in AQFP logic.
Abstract Adiabatic quantum-flux-parametron (AQFP) logic is an energy-efficient superconductor logic family. The latency of AQFP circuits is relatively long compared to that of other superconductor logic families and thus such circuits require low-latency clocking schemes. In a previous study, we proposed a low-latency clocking scheme called delay-line clocking, in which the latency for each logic operation is determined by the propagation delay of the excitation current, and demonstrated a simple AQFP buffer chain that adopts delay-line clocking. However, it is unclear whether more complex AQFP circuits can adopt delay-line clocking. In the present study, we demonstrate AQFP logic gates (AND and XOR gates) that use delay-line clocking as a step towards implementing large-scale AQFP circuits with delay-line clocking. AND and XOR gates with a latency of approximately 20 ps per gate are shown to operate at up to 5 and 4 GHz, respectively, in experiments. We also demonstrate that delay-line clocking enables phase skipping operation, in which some of the AQFP buffers for phase synchronization are removed to reduce the junction count and energy dissipation. The results indicate that delay-line clocking can enable low-latency, low-energy, large-scale AQFP circuits.
Adiabatic quantum-flux-parametron (AQFP) logic is a highly energy-efficient superconductor logic family. Traditionally, AQFP circuits have relied on the four-phase clocking scheme, which uses a pair of ac current sources with a 90° phase difference. The operation of each logic gate thus takes a quarter clock cycle, leading to a relatively long latency for some applications. In this Letter, we propose a low-latency clocking scheme for AQFP logic based on microwave power dividers (PDs). The whole circuit is powered by a single excitation current, which is equally split for each logic stage by a serial-type PD. As a result, the latency between adjacent logic stages is determined by the transmission line length (propagation delay) inside the PD, which can be much shorter than a quarter clock cycle. Note that the low-latency performance is independent of the horizontal length of the AQFP circuit, and thus, the proposed clocking scheme is applicable to large-scale designs where a large number of gates are horizontally placed in a single stage. For validation, several numerical simulations are conducted and a six-stage AQFP test circuit is demonstrated using the proposed power-dividing clocking scheme (with a designed latency of 20 ps per gate) at a temperature of 4.2 K.
Adiabatic quantum-flux-parametron (AQFP) logic is a superconductor logic family that can operate with low switching energy due to adiabatic switching. In a previous study, we proposed a low-latency clocking scheme called delay-line clocking, in which the latency for each logic operation is determined by the propagation delay of the excitation current. We demonstrated several AQFP logic gates with delay-line clocking and demonstrated a phase skipping operation, in which some of the AQFP buffers for phase synchronization are removed to reduce the junction count and energy dissipation. In the present study, we design and demonstrate an AQFP 8-bit ripple carry adder with delay-line clocking to show that delay-line clocking and the phase skipping operation are applicable to large-scale AQFP circuits. The latency of this adder is 960 ps, which is 40% of that for a conventional design. Moreover, due to the phase skipping operation, the junction count is reduced to approximately 70% of that for the conventional design. We find that this adder can operate at up to 4 GHz. The above results indicate that large-scale AQFP circuits can operate with low latency and low junction count by using delay-line clocking and a phase skipping operation.
Abstract Adiabatic quantum-flux-parametron (AQFP) logic stands as an energy-efficient superconductor logic family relying on ac excitations. Though a four-phase clocking scheme has been commonly applied to excite and clock AQFP circuits, the cost of multiple sources and long between-stage latency (a quarter clock cycle) remain unsatisfactory. These drawbacks are more severe for sequential logics, where feedback loops require both down-flow and reverse-flow AQFP gates, necessitating extra buffers and imposing a limit on operating depth at the same time. To overcome these restrictions, in this paper, we introduce a novel mixed clocking scheme for low-latency AQFP logic circuits allowing feedback loops. In particular, the down-flow part of the AQFP circuit is excited by an ac current through delay-lines, which can reduce the latency from input to output stages. Meanwhile, the reverse-flow part is clocked by 2 other ac currents with 90° phase difference to reduce the buffering gates. The proposed clocking scheme is first applied to a fundamental logic circuit, confirming correct functionality and low-latency operations for diverse feedback conditions. For experimental validation, we design and fabricate a 3-bit AQFP counter using the proposed clocking scheme based on an on-chip clock splitter. The circuit is examined at 4 GHz under 4.2 K temperature, where we obtain desired operations and wide excitation margins.
Adiabatic quantum-flux-parametron (AQFP) logic is an ultra-low-power superconductor logic family. AQFP logic gates are powered and clocked by dedicated clocking schemes using ac excitation currents to implement an energy-efficient switching process, adiabatic switching. We have proposed a low-latency clocking scheme, delay-line clocking, and demonstrated basic AQFP logic gates. In order to test more complex circuits, a serializer/deserializer (SerDes) should be incorporated into the AQFP circuit under test, since the number of input/output (I/O) cables is limited by equipment. Therefore, in the present study we propose and develop a novel SerDes for testing delay-line-clocked AQFP circuits by combining AQFP and rapid single-flux-quantum (RSFQ) logic families, which we refer to as the AQFP/RSFQ hybrid SerDes. The hybrid SerDes comprises RSFQ shift registers to facilitate the data storage during serial-to-parallel and parallel-to-serial conversion. Furthermore, all the component circuits in the hybrid SerDes are clocked by the identical excitation current to synchronize the AQFP and RSFQ parts. We fabricate and demonstrate a delay-line-clocked AQFP circuit (8-to-3 encoder, which is the largest delay-line-clocked circuit ever designed) integrated with the hybrid SerDes at 4.2 K up to 4.5 GHz. Our measurement results indicate that the hybrid SerDes enables the testing of delay-line-clocked AQFP circuits with only a few I/O cables and is thus a powerful tool for the development of very large-scale integration AQFP circuits.
Adiabatic quantum-flux-parametron (AQFP) circuits are very low-power due to zero static power consumption and adiabatic switching operations. However, compared to other superconducting circuits, such as rapid single-flux-quantum logic, the operation frequency is relatively low and the latency is relatively large. In this work, we propose multi-excitation AQFP (ME-AQFP) circuits for high-speed and low-latency operations. In ME-AQFP, the intrinsic periodicity of the potential energy of a Josephson device with respect to applied magnetic fluxes is utilized to multiply operation frequencies and reduce latency. In a numerical simulation, we demonstrated an ME-AQFP AND gate, which operates at 10 GHz or 20 GHz with 5-GHz excitation currents. We also evaluated the energy efficiency of ME-AQFP circuits. In an experiment, we successfully demonstrated an ME-AQFP XOR gate and an ME-AQFP full adder.