aqora

Measurement of Bit-Error-Rate of Single Flux Quantum Logic gates with optimized Josephson Comparator structure

Asakura Kenta

The Japan Society of Applied PhysicsFeb 6, 20150 citations

The Balanced Comparator as a Benchmark Circuit to Validate Josephson Simulators

Timur V. Filippov, Sukanya Sagarika Meher, M. Celik +4 more

The balanced comparator, a pair of Josephson junctions, is a key building block and decision-making element for the Rapid Single Flux Quantum (RSFQ) logic cells. The properties of the balanced comparator (BC) define the maximum clock frequency and bit error rate (BER) of RSFQ cells and circuits. Comparators are well characterized by two parameters, the gray zone (GZ) and the gray zone threshold (GZT). Both parameters depend on the dynamic properties of a pair of junctions forming the BC and its surrounding circuitry. In addition, the gray zone depends on the thermal noise in Josephson junctions. The GZ and GZT parameters can be easily measured for various balanced comparators and be used for model-to-hardware correlations. This makes the balanced comparator a unique circuit to validate and calibrate any Josephson simulator by comparing measured and simulated characteristics, including both dynamic and noise properties. In this paper we used a set of balanced comparators designed for the SFQ5ee fabrication process at MIT Lincoln Laboratory to validate and calibrate the Synopsys PrimeSim HSPICE simulator. We were able to match experimental and simulated results and reproduce in simulations the main features observed experimentally and predicted theoretically. A list of recommended design variations to validate a Josephson simulator is provided.The balanced comparator, a pair of Josephson junctions, is a key building block and decision-making element for the Rapid Single Flux Quantum (RSFQ) logic cells. The properties of the balanced comparator (BC) define the maximum clock frequency and bit error rate (BER) of RSFQ cells and circuits. Comparators are well characterized by two parameters, the gray zone (GZ) and the gray zone threshold (GZT). Both parameters depend on the dynamic properties of a pair of junctions forming the BC and its surrounding circuitry. In addition, the gray zone depends on the thermal noise in Josephson junctions. The GZ and GZT parameters can be easily measured for various balanced comparators and be used for model-to-hardware correlations. This makes the balanced comparator a unique circuit to validate and calibrate any Josephson simulator by comparing measured and simulated characteristics, including both dynamic and noise properties. In this paper we used a set of balanced comparators designed for the SFQ5ee fabrication process at MIT Lincoln Laboratory to validate and calibrate the Synopsys PrimeSim HSPICE simulator. We were able to match experimental and simulated results and reproduce in simulations the main features observed experimentally and predicted theoretically. A list of recommended design variations to validate a Josephson simulator is provided.

IEEE Transactions on Applied SuperconductivityNov 29, 20250 citations

Statistical analysis of error rate of large-scale single flux quantum logic circuit by considering fluctuation of timing parameters

Yuki Yamanashi, Kota Masubuchi, Nobuyuki Yoshikawa

Physica C SuperconductivityMar 8, 20163 citations

Evaluation of current sensitivity of quantum flux parametron

Yuki Yamanashi, Takashi Matsushima, Naoki Takeuchi +2 more

Abstract Current sensitivity of a quantum flux parametron (QFP) was evaluated by measuring gray zone width on the basis of both circuit simulation and measurements, for superconducting sensing systems composed of a superconducting sensor array and superconducting read-out and signal processing circuits. Simulation results indicate a narrow gray zone width can be obtained by decreasing inductances comprising the QFP. Moreover, both high-sensitivity and low-power operation of the QFP can be realized by using optimized circuit parameters with an excitation current that has long rise time. A gray zone width of approximately 0.5 μ A, which is smaller than that of the Josephson current comparator based on a single flux quantum circuit, was obtained experimentally, using a trapezoidal excitation current with rise time of 50 μ s. These results indicate the QFP is promising for the read-out circuit in superconducting sensing systems, due to its high sensitivity and low power consumption.Abstract Current sensitivity of a quantum flux parametron (QFP) was evaluated by measuring gray zone width on the basis of both circuit simulation and measurements, for superconducting sensing systems composed of a superconducting sensor array and superconducting read-out and signal processing circuits. Simulation results indicate a narrow gray zone width can be obtained by decreasing inductances comprising the QFP. Moreover, both high-sensitivity and low-power operation of the QFP can be realized by using optimized circuit parameters with an excitation current that has long rise time. A gray zone width of approximately 0.5 μ A, which is smaller than that of the Josephson current comparator based on a single flux quantum circuit, was obtained experimentally, using a trapezoidal excitation current with rise time of 50 μ s. These results indicate the QFP is promising for the read-out circuit in superconducting sensing systems, due to its high sensitivity and low power consumption.

Superconductor Science and TechnologyJul 4, 201714 citations

Noise-Aware Error Rate Reduction of Single-Qubit Gates

Thomas J. Maldonado, Alexey Galda, Johannes Flick +2 more

Bulletin of the American Physical SocietyMar 15, 20210 citations

Investigation of High-T c Single Flux Quantum Logic Gates

Kazuo Saitoh, Hiroyuki Fuke

IEICE Transactions on ElectronicsOct 25, 19970 citations

Improvement of bit-error-rate of single flux quantum logic gate by optimizing gray zone width of comparator

Related papers

Improvement of bit-error-rate of single flux quantum logic gate by optimizing gray zone width of comparator

Related papers