Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Photonics Technology Letters

Low-Loss High-Speed C-Band Fiber-Optic Switch Suitable for Quantum Signals

Kim Fook Lee, Gregory S. Kanter

Published Mar 18, 2019• 12 citations
Publisher

Abstract

Quantum signals such as entangled photons are typically at the sub-photon level and, thus, require near noise-less and low-loss components for their manipulation and processing. A common signal-manipulation tool is a 2 × 2 switch, and many applications of quantum switches also require fast switching rates and input signals in the fiber-friendly 1550-nm band. Traditional optical switching technology does not simultaneously meet all the desired metrics for a quantum switch. We demonstrate a low-noise fiber-optic photonic switch based on cross phase modulation that is fast (sub-ns), low loss (<;1 dB), and operates in the 1550-nm wavelength band.

DOI
10.1109/lpt.2019.2905593

Related papers

Low-Loss High-Speed Fiber-Optic Switch for Quantum State Manipulation

Kim Fook Lee, Gregory S. Kanter

We demonstrate a fiber-based photonic switch that is fast (sub ns), low loss (1 dB), low noise, and operates in the 1550 nm band. The switch operation is characterized and potential applications are discussed.

IEEE/LEOS Summer Topical Meetings•Jul 1, 2018•2 citations

Entanglement-Preserving Photonic Switching: Full Cross-Bar Operation With Quantum Data Streams

Neal N. Oza, Yu‐Ping Huang, Prem Kumar

As the field of quantum communications matures and adopts larger network topologies, it will require switches capable of multiplexing and demultiplexing entangled photons between network nodes. Such switches will need to operate at high speeds, with low loss, and minimal signal-band noise, while also retaining the quantum state of the routed photons. We present an all-optical, fiber-based, dual-in, dual-out switch that has a switching window of 45 ps and an insertion loss of <;3.0 dB. In addition, the switch introduces minimal degradation to the quantum state of the routed entangled photons. As a test of the switch's utility, we demultiplex a single quantum channel from a 6.5-GHz dual-channel quantum data stream. The recovered quantum state exhibits a fidelity of 96.2%±1.2% with the prepared state.

IEEE Photonics Technology Letters•Jan 24, 2014•18 citations

Ultrafast switching of telecom photon-number states

Kate L. Fenwick, Frédéric Bouchard, Alicia Sit +7 more

A crucial component of photonic quantum information processing platforms is the ability to modulate, route, convert, and switch quantum states of light noiselessly with low insertion loss. For instance, a high-speed, low-loss optical switch is crucial for scaling quantum photonic systems that rely on measurement-based feed-forward approaches. Such a device will also ideally be capable of operating on photon-number states, which can act as non-Gaussian resources. Here, we demonstrate ultrafast all-optical switching of heralded photon-number states, of up to 6 photons, using the optical Kerr effect in a single-mode fiber. A local birefringence is created by a high-intensity pump pulse at a center wavelength of 1030 nm which overlaps temporally with the 1550 nm photons in the fiber. A switching efficiency of $>$99 % is reached with a resolution of 2.3 ps, an insertion loss of $2.27\pm0.08$ dB, and a signal-to-noise ratio of 32,000.

arXiv:2504.12376•Physical Review A•Jan 23, 2026•0 citations

Low-loss all-optical ns-switching for single-photon routing in scalable integrated quantum photonics

Fabian Ruf, Lars Nielsen, Mircea Balauroiu +2 more

Efficient single-photon routing and switching are crucial for optical quantum computing and communication. For this purpose, all-optical switches are designed for gigahertz bandwidths. The switching mechanism is based on the optical Kerr effect via cross-phase modulation (CPM) of the single-photon signal by a strong 1550-nm pump pulse. For energy-efficient switching, this nonlinear effect is exploited in a microresonator that can either be used directly as an intensity switch in a typical add–drop configuration or as a phase shifter in a Mach–Zehnder interferometer (MZI) structure. To speed up resonance build-up and quenching, a pre-emphasis build and an off-resonance wipe pulse are used. The proposed designs are verified by traveling-wave simulations which demonstrate that 0.1 dB insertion loss and ~1 ns switching windows can be achieved. For a scalable out-of-the-lab transfer, we investigate the feasibility of the proposed switch designs for fabrication in a mature photonic integrated circuit (PIC) platform. In particular, silicon nitride PICs have demonstrated record-low losses which makes them suitable for single-photon applications. By parametric modelling of the microresonator’s directional couplers based on Lumerical EME and 2.5-dimensional varFDTD simulations, the required power transmission coefficients for both signal and pump wavelength can be achieved. This results in an all-optical switch design ready for fabrication in a commercial PIC foundry which can potentially enable scalable architectures for quantum photonic applications.

Integrated Photonics Platforms•May 26, 2022•3 citations

Analysis and Design of Low-Loss and Fast All-Optical Switch Elements on Silicon Nitride for Integrated Quantum Photonics

Fabian Ruf, Lars Nielsen, Nicolas Volet +1 more

Fast and ultra-low loss single-photon switching and routing are essential for photonic quantum computation and communication. To address this need in a scalable fashion, all-optical switches that can be fabricated in an ultra-low loss and mature Si$_{3}$N$_{4}$photonic integrated circuit (PIC) foundry platform are designed and optimized for sub-ns switching times suitable for deterministic quantum-dot single-photon sources. The working principle relies on cross-phase modulation (XPM) of the single photons with a 1550-nm pump pulse and is enhanced by a ring resonator. Two different designs of the primary switch element are theoretically studied, namely a ring resonator intensity switch (RRIS) based on resonance shifting due to XPM and a ring resonator phase switch (RRPS) acting as an all-optical phase shifter in a Mach–Zehnder interferometer. As a novel approach to speed up the switching, chirped pre-emphasis and wipe sections for the pump pulses are utilized. A design tool is established from analytical expressions and serves as starting point for further optimization using a dedicated travelling-wave model (TWM). The TWM demonstrates the feasibility of both designs to be driven by either the proposed pre-emphasis pulse shape or a train of chirped Gaussian pulses. While the RRPS turns out to require less pump energy, its operation is more sensitive to pump-power fluctuations. Insertion losses below 0.1 dB and a power consumption below 5 nJ at 1 GHz switching rates for both configurations prove the potential of this concept for scalable quantum photonic applications.

Journal of Lightwave Technology•Oct 10, 2022•12 citations

Pulse Retiming for Improved Switching Rates in Low-Noise Cross-Phase-Modulation-Based Fiber Switches

Kim Fook Lee, Paul M. Moraw, Daniel R. Reilly +1 more

Temporal multiplexing or demultiplexing of quantum signals would benefit from low-loss, high speed, high rate, and low noise switches. Fiber cross-phase-modulation based switches are a promising solution, but their maximum switching rate is usually limited by pump power limitations. We demonstrate the use of mid-stage pump-pulse re-timing to improve the pump-power efficiency and thus increase the maximum switching rates of such devices. The maximum average pump pulse rate of the switch is shown to increase by more than 50% to 800 MHz when employing pump-pulse retiming. We furthermore confirm the suitability of the switch for quantum signals by sending one of a pair of quantum-correlated photons through the switch while incurring no noticeable degradation of correlations.

IEEE Photonics Technology Letters•Dec 11, 2020•5 citations
Quantum signals such as entangled photons are typically at the sub-photon level and, thus, require near noise-less and low-loss components for their manipulation and processing. A common signal-manipulation tool is a 2 × 2 switch, and many applications of quantum switches also require fast switching rates and input signals in the fiber-friendly 1550-nm band. Traditional optical switching technology does not simultaneously meet all the desired metrics for a quantum switch. We demonstrate a low-noise fiber-optic photonic switch based on cross phase modulation that is fast (sub-ns), low loss (<;1 dB), and operates in the 1550-nm wavelength band.
As the field of quantum communications matures and adopts larger network topologies, it will require switches capable of multiplexing and demultiplexing entangled photons between network nodes. Such switches will need to operate at high speeds, with low loss, and minimal signal-band noise, while also retaining the quantum state of the routed photons. We present an all-optical, fiber-based, dual-in, dual-out switch that has a switching window of 45 ps and an insertion loss of <;3.0 dB. In addition, the switch introduces minimal degradation to the quantum state of the routed entangled photons. As a test of the switch's utility, we demultiplex a single quantum channel from a 6.5-GHz dual-channel quantum data stream. The recovered quantum state exhibits a fidelity of 96.2%±1.2% with the prepared state.
A crucial component of photonic quantum information processing platforms is the ability to modulate, route, convert, and switch quantum states of light noiselessly with low insertion loss. For instance, a high-speed, low-loss optical switch is crucial for scaling quantum photonic systems that rely on measurement-based feed-forward approaches. Such a device will also ideally be capable of operating on photon-number states, which can act as non-Gaussian resources. Here, we demonstrate ultrafast all-optical switching of heralded photon-number states, of up to 6 photons, using the optical Kerr effect in a single-mode fiber. A local birefringence is created by a high-intensity pump pulse at a center wavelength of 1030 nm which overlaps temporally with the 1550 nm photons in the fiber. A switching efficiency of $>$99 % is reached with a resolution of 2.3 ps, an insertion loss of 2.27±0.082.27\pm0.082.27±0.08 dB, and a signal-to-noise ratio of 32,000.
Efficient single-photon routing and switching are crucial for optical quantum computing and communication. For this purpose, all-optical switches are designed for gigahertz bandwidths. The switching mechanism is based on the optical Kerr effect via cross-phase modulation (CPM) of the single-photon signal by a strong 1550-nm pump pulse. For energy-efficient switching, this nonlinear effect is exploited in a microresonator that can either be used directly as an intensity switch in a typical add–drop configuration or as a phase shifter in a Mach–Zehnder interferometer (MZI) structure. To speed up resonance build-up and quenching, a pre-emphasis build and an off-resonance wipe pulse are used. The proposed designs are verified by traveling-wave simulations which demonstrate that 0.1 dB insertion loss and ~1 ns switching windows can be achieved. For a scalable out-of-the-lab transfer, we investigate the feasibility of the proposed switch designs for fabrication in a mature photonic integrated circuit (PIC) platform. In particular, silicon nitride PICs have demonstrated record-low losses which makes them suitable for single-photon applications. By parametric modelling of the microresonator’s directional couplers based on Lumerical EME and 2.5-dimensional varFDTD simulations, the required power transmission coefficients for both signal and pump wavelength can be achieved. This results in an all-optical switch design ready for fabrication in a commercial PIC foundry which can potentially enable scalable architectures for quantum photonic applications.
Fast and ultra-low loss single-photon switching and routing are essential for photonic quantum computation and communication. To address this need in a scalable fashion, all-optical switches that can be fabricated in an ultra-low loss and mature Si3_{3}3​N4_{4}4​photonic integrated circuit (PIC) foundry platform are designed and optimized for sub-ns switching times suitable for deterministic quantum-dot single-photon sources. The working principle relies on cross-phase modulation (XPM) of the single photons with a 1550-nm pump pulse and is enhanced by a ring resonator. Two different designs of the primary switch element are theoretically studied, namely a ring resonator intensity switch (RRIS) based on resonance shifting due to XPM and a ring resonator phase switch (RRPS) acting as an all-optical phase shifter in a Mach–Zehnder interferometer. As a novel approach to speed up the switching, chirped pre-emphasis and wipe sections for the pump pulses are utilized. A design tool is established from analytical expressions and serves as starting point for further optimization using a dedicated travelling-wave model (TWM). The TWM demonstrates the feasibility of both designs to be driven by either the proposed pre-emphasis pulse shape or a train of chirped Gaussian pulses. While the RRPS turns out to require less pump energy, its operation is more sensitive to pump-power fluctuations. Insertion losses below 0.1 dB and a power consumption below 5 nJ at 1 GHz switching rates for both configurations prove the potential of this concept for scalable quantum photonic applications.
Temporal multiplexing or demultiplexing of quantum signals would benefit from low-loss, high speed, high rate, and low noise switches. Fiber cross-phase-modulation based switches are a promising solution, but their maximum switching rate is usually limited by pump power limitations. We demonstrate the use of mid-stage pump-pulse re-timing to improve the pump-power efficiency and thus increase the maximum switching rates of such devices. The maximum average pump pulse rate of the switch is shown to increase by more than 50% to 800 MHz when employing pump-pulse retiming. We furthermore confirm the suitability of the switch for quantum signals by sending one of a pair of quantum-correlated photons through the switch while incurring no noticeable degradation of correlations.