Traveling-wave parametric amplifiers based on superconducting NbTiN films are being developed that provide gain over nearly an octave of bandwidth at microwave frequencies. The amplifiers are non-linear transmission lines, where the nonlinearity comes from the current dependence of the kinetic inductance. Amplification results from three and four-wave mixing processes, and phase matching over a wide frequency range is achieved by engineering the dispersion characteristics of the transmission line. Recent noise measurements over a wide frequency band demonstrate that the added noise of these amplifiers is close to one half photon, consistent with the quantum limit for a phase preserving amplifier. We will discuss applications of this class of amplifier to astronomical instruments.
Traveling-wave parametric amplifiers based on superconducting NbTiN films are being developed that provide gain over nearly an octave of bandwidth at microwave frequencies. The amplifiers are non-linear transmission lines, where the nonlinearity comes from the current dependence of the kinetic inductance. Amplification results from three and four-wave mixing processes, and phase matching over a wide frequency range is achieved by engineering the dispersion characteristics of the transmission line. Recent noise measurements over a wide frequency band demonstrate that the added noise of these amplifiers is close to one half photon, consistent with the quantum limit for a phase preserving amplifier. We will discuss applications of this class of amplifier to astronomical instruments.
The traveling-wave kinetic inductance parametric (TKIP) amplifier is a new amplifier technology capable of near quantum-limited sensitivity over a wide instantaneous bandwidth. Microwave frequency versions of these amplifiers, which are based on four-wave mixing in an NbTiN coplanar waveguide transmission line, have demonstrated high gain and noise corresponding to a few photons at several GHz. Their simple design is easily scalable to higher frequency, allowing for operation up to near the (> 1 THz) gap frequency of NbTiN. We will discuss the current state of the art of the TKIP operating at microwave frequencies and the potential use of these amplifiers as front ends for receivers in the millimeter and submillimeter bands. As an example, we describe the design of a TKIP tuned for the W-band.
Abstract A Kinetic Inductance Traveling Wave Amplifier (KIT) utilizes the nonlinear kinetic inductance of superconducting films, particularly niobium titanium nitride (NbTiN), for parametric amplification. These amplifiers achieve remarkable performance in terms of gain, bandwidth, and compression power and frequently approach the quantum limit for noise. However, most KIT demonstrations have been isolated from practical device readout systems. Using a KIT as the first amplifier in the readout chain of an unoptimized microwave SQUID multiplexer coupled to a transition-edge sensor microcalorimeter, we see an initial improvement in the flux noise [1]. One challenge in KIT integration is the considerable microwave pump power required to drive the non-linearity. To address this, we have initiated efforts to reduce the pump power by using thinner NbTiN films and an inverted microstrip transmission line design. In this article, we present the new transmission line design, fabrication procedure, and initial device characterization—including gain and added noise. These devices exhibit over 10 dB of gain with a 3 dB bandwidth of approximately 5.5–7.25 GHz, a maximum practical gain of 12 dB, and typical gain ripple under 4 dB peak to peak. We observe an appreciable impedance mismatch in the NbTiN transmission line, which is likely the source of the majority of the gain ripple. Finally, we perform an initial noise characterization and demonstrate system-added noise of three quanta or less over nearly the entire 3 dB bandwidth.
Abstract A wide-bandwidth and low-noise amplification chain in the microwave regime is crucial for the efficient read-out of quantum systems based on superconducting detectors, such as Microwave Kinetic Inductance Detectors (MKIDs), Transition Edge Sensors (TESs), Magnetic Microcalorimeters (MMCs), and RF cavities, as well as qubits. Kinetic Inductance Travelling Wave Parametric Amplifiers (KI-TWPAs) operated in a three-wave mixing fashion have demonstrated exceptional dynamic range and low-noise performance, approaching the quantum limit. These amplifiers can be fabricated using a single layer of a high kinetic inductance film as weakly dispersive artificial transmission lines, with the ability to control the phase-matched bandwidth through dispersion engineering. In this study, we present the optimisation of the rf sputter-deposition process of NbTiN films using a Nb80%Ti20% target, with the goal of achieving precise control over film characteristics, resulting in high kinetic inductance while maintaining a high transition temperature. The parameter landscape related to the different sputtering conditions, such as pressure, power, and nitrogen flow, has been explored and the film thickness has been used as a fine-tuning parameter to adjust the properties of the final NbTiN films used for the fabrication of KI-TWPAs. As a final result, we have obtained a NbTiN film with a kinetic inductance of 8.5 pH/sq which we have exploited to fabricate KI-TWPA prototype devices, showing promising amplification performance.
Kinetic inductance traveling-wave parametric amplifiers (KI-TWPAs) have a wide instantaneous bandwidth with a near quantum-limited noise performance and a relatively high dynamic range. Because of this, they are suitable readout devices for cryogenic detectors and superconducting qubits and have a variety of applications in quantum sensing. This work discusses the design, fabrication, and performance of a KI-TWPA based on four-wave mixing in a NbTiN microstrip transmission line. This device amplifies a signal band from 4 to 8 GHz without contamination from image tones, which are produced in a separate higher frequency band. The 4–8 GHz band is commonly used to read out cryogenic detectors, such as microwave kinetic inductance detectors and Josephson junction-based qubits. We report a measured maximum gain of over 20 dB using four-wave mixing with a 1 dB gain compression point of −58 dBm at 15 dB of gain over that band. The bandwidth and peak gain are tunable by adjusting the pump-tone frequency and power. Using a Y-factor method, we measure an amplifier-added noise of 0.5 ≤ Nadded ≤ 1.5 photons from 4.5 to 8 GHz.
Traveling-wave parametric amplifiers may be fabricated from superconducting films that exhibit highly nonlinear kinetic inductance. The coplanar waveguide of such a microwave device, extending to a meter or more in length but compacted to reside on a chip of the order of a square centimeter, is engineered with periodic variations in its width. These width variations, or loadings, alter the dispersion characteristics of a nonlinear current propagating along the waveguide, changing its group velocity and modulation behavior. A strong pump and a small signal injected into one end of the waveguide mix parametrically in the presence of the nonlinear kinetic inductance. Engineered dispersion induces the favorable conditions of overall phase matching, leading to generation of idler products as well as signal amplification of wide bandwidth, high dynamic range, and low noise, making the device of particular use in quantum computing and photon detection. The authors present a theoretical framework in which signal gain may be calculated solely from loading design. This involves construction of a metamaterial band theory of the engineered dispersion, which is used as a basis to describe the mixing of nonlinear traveling waves.
Ultralow-noise microwave amplification and detection play a central role in different applications, going from fundamental physics experiments to the deployment of quantum technologies. In many applications the necessity of reading multiple detectors, or cavities or qubits, calls for large bandwidth amplifiers with the lowest possible noise. Current technologies are based on High Electron Mobility Transistors and Josephson Parametric Amplifiers. Both have limitations, the former in terms of the minimum noise, the latter in terms of bandwidth. Superconducting Traveling Wave Parametric Amplifiers (TWPAs) have the potential of offering quantum limited noise and large bandwidth. These amplifiers are based on the parametric amplification of microwaves traveling along a transmission line with embedded nonlinear elements. We are developing superconducting TWPAs based both on Josephson junction arrays (Traveling Wave Josephson Parametric Amplifiers) and on nonlinear kinetic inductance (Dispersion Engineered Traveling Wave Kinetic Inductance Amplifiers). Our goal is to achieve large bandwidth (in the 5 to 10 GHz range), large gain (more than 20 dB), large saturation power (more than −50 dBm), and near quantum limited noise (noise temperature less than 600 mK). Current achievements in the design and development of the high performance TWPAs are here reported and discussed, together with current limitations and possible future developments.