Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Laser Physics

Detuning radio-frequency electrometry using Rydberg atoms in a room-temperature vapor cell

Linjie Zhang, Yue Jia, Mingyong Jing, Liping Guo, Hao Zhang, Liantuan Xiao, Suotang Jia

Published Feb 19, 2019• 25 citations
Publisher

Abstract

Traceable radio-frequency electric field measurements with high sensitivity have been demonstrated from the centimeter wave to the millimeter wave using room-temperature Rydberg atoms. Here, we investigate the splitting spectra of electromagnetically induced transparency induced by a radio-frequency electric field, which is detuned from the resonant frequency of transitions between two Rydberg states, 47D 5/2 ↔ 48P 3/2 . By varying the detuning of the radio-frequency electric field, we measure the separation between the two peaks, and in particular their relative height. The resulting measured resonant transition frequency between two Rydberg states is found to exhibit a visible change when the power of the radio-frequency electric field is varied, thus causing uncertainty in the traceable radio-frequency electric field measurement. Further, the effect of detuning of the probe light on the radio-frequency electric field measurement is presented.

DOI
10.1088/1555-6611/aaffcb

Related papers

Using frequency detuning to improve the sensitivity of electric field measurements via electromagnetically induced transparency and Autler-Townes splitting in Rydberg atoms

Matthew T. Simons, Joshua A. Gordon, Christopher L. Holloway +3 more

In this work, we demonstrate an approach for improved sensitivity in weak radio frequency (RF) electric-field strength measurements using Rydberg electromagnetically induced transparency (EIT) in an atomic vapor. This is accomplished by varying the RF frequency around a resonant atomic transition and extrapolating the weak on-resonant field strength from the resulting off-resonant Autler-Townes (AT) splittings. This measurement remains directly traceable to SI compared to previous techniques, precluding any knowledge of experimental parameters such as optical beam powers as is the case when using the curvature of the EIT line shape to measure weak fields. We use this approach to measure weak RF fields at 182 GHz and 208 GHz demonstrating improvement greater than a factor of 2 in the measurement sensitivity compared to on-resonant AT splitting RF electric field measurements.

Applied Physics Letters•Apr 25, 2016•155 citations

Electromagnetically induced transparency spectra of cesium Rydberg atoms decorated by radio-frequency fields

Yulong Han, Bang Liu, Kan Zhang +3 more

The large electric dipole moment of the Rydberg atom allows for strong coupling with weak electric fields, and is widely used in electric field measurements because of its reproducibility, precision and stability. The combination of Rydberg atoms and electromagnetically induced transparency (EIT) technology has been used for detecting and characterizing radio-frequency (RF) electric fields. In this work, by selecting probe light (852 nm), dressed light (1470 nm), and coupled light (780 nm), the Rydberg state (49P3/2) of Cs atom is prepared by using a three-photon excitation scheme through using all-infrared light excitation of Rydberg atoms. We experimentally observe the EIT spectra of the Rydberg states decorated by radio-frequency electric fields, which optically detects Rydberg atoms. The effect of the amplitude and frequency of the RF electric field on the spectrum is explored in light of changes in the EIT spectrum. The results show that in the region of weak electric field, only the ac Stark energy shift and spectral broadening occur. As the electric field is further enhanced, the sideband phenomenon occurs in both the primary peak and secondary peak of the EIT. In the region of strong field, the Rydberg energy level produces a series of Floquet states with higher-order terms, as well as state shifting and mixing, resulting in asymmetry in the spectra of the EIT sideband peaks. The effect of frequency on the shielding effect of the Cs vapor cell is further discussed based on the shift of the main peak of the EIT. The demodulation of the electric field in a range of 50 Hz–1 kHz with a fidelity of 95% is achieved by modulating the low-frequency electric field to the RF electric field. The results can provide valuable references for spectral detection and traceable measurements of low-frequency electric fields.

Acta Physica Sinica•Jan 1, 2024•1 citation

Dispersive radio frequency electrometry using Rydberg atoms in a prism-shaped atomic vapor cell

Haoquan Fan, Santosh Kumar, Harald Kübler +1 more

Abstract We introduce a method to measure radio frequency (RF) electric fields (E-fields) using atoms contained in a prism-shaped vapor cell. The method utilizes the concept of electromagnetically induced transparency with Rydberg atoms. The RF E-field induces changes in the index of refraction of the vapor resulting in deflection of the probe laser beam as it passes through the prism-shaped vapor cell. We measured a minimum RF E-field of 8.25 μ Vcm − 1 with a sensitivity of ∼ 46.5 μ Vcm − 1 Hz − 1 / 2 . The experimental results agree with a numerical model that includes dephasing effects. We discuss possible improvements to obtain higher sensitivity for RF E-field measurements.

Journal of Physics B Atomic Molecular and Optical Physics•May 5, 2016•38 citations

Broadband Rydberg atom-based radio-frequency field sensor

Jiao Yue-Chun, Jianming Zhao, Jia Suo-Tang

Significant progress has been made in atom-based measurements of length, time, gravity and electromagnetic fields in recently years. Rydberg atom-based microwave electric field measurement, using electromagnetically induced transparency (EIT) in room temperature alkali-metal vapors, has been extensively investigated and aroused the broad interest. This approach may establish a new standard for the measurements of microwave (MW) and radio frequency (RF) electric fields.In this review, we describe the work on a new method of measuring electric fields based on quantum interference by using either cesium or rubidium atoms contained in a dielectric vapor cell. Rydberg atoms with principal quantum number n >>1 have large direct current (DC) polarizabilities and microwave transition dipole moments, thereby making them extremely sensitive to external electric fields. Using the Rydberg three-level EIT to detect the level splitting and shift that is induced by the external field, we can realize a rapid and robust self-calibration method of measuring the electric field in a frequency range from 0.01 GHz to 1000 GHz. For the MW electric field (frequency range > 1 GHz), the MW field causes the Rydberg states to split, known as an Autler-Townes splitting (A-T) effect when the applied microwave can resonate with adjacent Rydberg states. The MW coupled A-T splitting is proportional to the applied electric field strength, from which the field strength is measured. Using the EIT window, a high sensitivity of 3 μV·cm-1·Hz-1/2 and small electric field of 1 μV/cm are expected to be achieved with a modest setup, and the limitations of the sensitivity are also addressed in the review. For the RF field at frequency mj EIT lines, and avoided crossings formed with the fine-structure levels of equal mj and different J's, which is used to calibrate and measure the RF field amplitude. On the other hand, the dependence of the EIT-line strength on the RF field polarization provides a fast and robust polarization measurement of RF fields based on matching experimental data with a theoretical simulation. The measurements of minimum strengths and sensitivity of RF fields based on Rydberg atoms are one order magnitude below the values obtained by traditional antenna methods. The atom-based field measurement paves the way for determining fields through calibration-free, invariable atomic properties and miniaturization. We also propose its various potential applications in the future.

Acta Physica Sinica•Jan 1, 2018•7 citations

Atom-based RF electric field metrology above 100 GHz

Matthew T. Simons, Joshua A. Gordon, Christopher L. Holloway

Atom-based radio-frequency (RF) electric field probes have the potential to improve electric field measurements for a broad range of frequencies (from a few GHz to 100s of GHz) and field strengths (mV/m to kV/m). For these probes to become a common measurement method, their range must be extended to high frequency (>100 GHz) and low field strength regimes. We present SI-traceable electric field measurements of RF fields above 100 GHz, using Autler-Townes splitting of Rydberg electromagnetically-induced transparency in a rubidium (Rb) vapor. We also demonstrate several techniques, including RF detuning from resonance and enhanced absorption, for increasing the probe sensitivity.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Feb 25, 2016•4 citations

Electromagnetically induced transparency in modulated laser fields

Yuechun Jiao, Zhiwei Yang, Hao Zhang +4 more

Abstract We study electromagnetically induced transparency (EIT) in a room-temperature cesium vapor cell using wavelength-modulated probe laser light. In the utilized cascade level scheme, the probe laser drives the lower transition 6 S 1 / 2 ( F = 4) → 6 P 3 / 2 ( F ’ = 5), while the coupling laser drives the Rydberg transition 6 P 3 / 2 → 57 S 1 / 2 . The probe laser has a fixed average frequency and is modulated at a frequency of a few kHz, with a variable modulation amplitude in the range of tens of MHz. The probe transmission is measured as a function of the detuning of the coupling laser from the Rydberg resonance. The first-harmonic demodulated EIT signal has two peaks that are, in the case of large modulation amplitude, separated by the peak-to-peak modulation amplitude of the probe laser times a scaling factor λ p / λ c , where λ p and λ c are the probe- and coupling-laser wavelengths. The scaling factor is due to Doppler shifts in the EIT geometry. Second-harmonic demodulated EIT signals, obtained with small modulation amplitudes, yield spectral lines that are much narrower than corresponding lines in the modulation-free EIT spectra. The resultant spectroscopic resolution enhancement is conducive to improved measurements of radio-frequency (RF) fields based on Rydberg-atom EIT, an approach in which the response of Rydberg atoms to RF fields is exploited to characterize RF fields. Here, we employ wavelength modulation spectroscopy to reduce the uncertainty of atom-based frequency and field measurement of an RF field in the VHF radio band.

Journal of Physics B Atomic Molecular and Optical Physics•Dec 19, 2016•1 citation
Traceable radio-frequency electric field measurements with high sensitivity have been demonstrated from the centimeter wave to the millimeter wave using room-temperature Rydberg atoms. Here, we investigate the splitting spectra of electromagnetically induced transparency induced by a radio-frequency electric field, which is detuned from the resonant frequency of transitions between two Rydberg states, 47D 5/2 ↔ 48P 3/2 . By varying the detuning of the radio-frequency electric field, we measure the separation between the two peaks, and in particular their relative height. The resulting measured resonant transition frequency between two Rydberg states is found to exhibit a visible change when the power of the radio-frequency electric field is varied, thus causing uncertainty in the traceable radio-frequency electric field measurement. Further, the effect of detuning of the probe light on the radio-frequency electric field measurement is presented.
In this work, we demonstrate an approach for improved sensitivity in weak radio frequency (RF) electric-field strength measurements using Rydberg electromagnetically induced transparency (EIT) in an atomic vapor. This is accomplished by varying the RF frequency around a resonant atomic transition and extrapolating the weak on-resonant field strength from the resulting off-resonant Autler-Townes (AT) splittings. This measurement remains directly traceable to SI compared to previous techniques, precluding any knowledge of experimental parameters such as optical beam powers as is the case when using the curvature of the EIT line shape to measure weak fields. We use this approach to measure weak RF fields at 182 GHz and 208 GHz demonstrating improvement greater than a factor of 2 in the measurement sensitivity compared to on-resonant AT splitting RF electric field measurements.
The large electric dipole moment of the Rydberg atom allows for strong coupling with weak electric fields, and is widely used in electric field measurements because of its reproducibility, precision and stability. The combination of Rydberg atoms and electromagnetically induced transparency (EIT) technology has been used for detecting and characterizing radio-frequency (RF) electric fields. In this work, by selecting probe light (852 nm), dressed light (1470 nm), and coupled light (780 nm), the Rydberg state (49P3/2) of Cs atom is prepared by using a three-photon excitation scheme through using all-infrared light excitation of Rydberg atoms. We experimentally observe the EIT spectra of the Rydberg states decorated by radio-frequency electric fields, which optically detects Rydberg atoms. The effect of the amplitude and frequency of the RF electric field on the spectrum is explored in light of changes in the EIT spectrum. The results show that in the region of weak electric field, only the ac Stark energy shift and spectral broadening occur. As the electric field is further enhanced, the sideband phenomenon occurs in both the primary peak and secondary peak of the EIT. In the region of strong field, the Rydberg energy level produces a series of Floquet states with higher-order terms, as well as state shifting and mixing, resulting in asymmetry in the spectra of the EIT sideband peaks. The effect of frequency on the shielding effect of the Cs vapor cell is further discussed based on the shift of the main peak of the EIT. The demodulation of the electric field in a range of 50 Hz–1 kHz with a fidelity of 95% is achieved by modulating the low-frequency electric field to the RF electric field. The results can provide valuable references for spectral detection and traceable measurements of low-frequency electric fields.
Abstract We introduce a method to measure radio frequency (RF) electric fields (E-fields) using atoms contained in a prism-shaped vapor cell. The method utilizes the concept of electromagnetically induced transparency with Rydberg atoms. The RF E-field induces changes in the index of refraction of the vapor resulting in deflection of the probe laser beam as it passes through the prism-shaped vapor cell. We measured a minimum RF E-field of 8.25 μ Vcm − 1 with a sensitivity of ∼ 46.5 μ Vcm − 1 Hz − 1 / 2 . The experimental results agree with a numerical model that includes dephasing effects. We discuss possible improvements to obtain higher sensitivity for RF E-field measurements.
Significant progress has been made in atom-based measurements of length, time, gravity and electromagnetic fields in recently years. Rydberg atom-based microwave electric field measurement, using electromagnetically induced transparency (EIT) in room temperature alkali-metal vapors, has been extensively investigated and aroused the broad interest. This approach may establish a new standard for the measurements of microwave (MW) and radio frequency (RF) electric fields.In this review, we describe the work on a new method of measuring electric fields based on quantum interference by using either cesium or rubidium atoms contained in a dielectric vapor cell. Rydberg atoms with principal quantum number n >>1 have large direct current (DC) polarizabilities and microwave transition dipole moments, thereby making them extremely sensitive to external electric fields. Using the Rydberg three-level EIT to detect the level splitting and shift that is induced by the external field, we can realize a rapid and robust self-calibration method of measuring the electric field in a frequency range from 0.01 GHz to 1000 GHz. For the MW electric field (frequency range > 1 GHz), the MW field causes the Rydberg states to split, known as an Autler-Townes splitting (A-T) effect when the applied microwave can resonate with adjacent Rydberg states. The MW coupled A-T splitting is proportional to the applied electric field strength, from which the field strength is measured. Using the EIT window, a high sensitivity of 3 μV·cm-1·Hz-1/2 and small electric field of 1 μV/cm are expected to be achieved with a modest setup, and the limitations of the sensitivity are also addressed in the review. For the RF field at frequency mj EIT lines, and avoided crossings formed with the fine-structure levels of equal mj and different J's, which is used to calibrate and measure the RF field amplitude. On the other hand, the dependence of the EIT-line strength on the RF field polarization provides a fast and robust polarization measurement of RF fields based on matching experimental data with a theoretical simulation. The measurements of minimum strengths and sensitivity of RF fields based on Rydberg atoms are one order magnitude below the values obtained by traditional antenna methods. The atom-based field measurement paves the way for determining fields through calibration-free, invariable atomic properties and miniaturization. We also propose its various potential applications in the future.
Atom-based radio-frequency (RF) electric field probes have the potential to improve electric field measurements for a broad range of frequencies (from a few GHz to 100s of GHz) and field strengths (mV/m to kV/m). For these probes to become a common measurement method, their range must be extended to high frequency (>100 GHz) and low field strength regimes. We present SI-traceable electric field measurements of RF fields above 100 GHz, using Autler-Townes splitting of Rydberg electromagnetically-induced transparency in a rubidium (Rb) vapor. We also demonstrate several techniques, including RF detuning from resonance and enhanced absorption, for increasing the probe sensitivity.
Abstract We study electromagnetically induced transparency (EIT) in a room-temperature cesium vapor cell using wavelength-modulated probe laser light. In the utilized cascade level scheme, the probe laser drives the lower transition 6 S 1 / 2 ( F = 4) → 6 P 3 / 2 ( F ’ = 5), while the coupling laser drives the Rydberg transition 6 P 3 / 2 → 57 S 1 / 2 . The probe laser has a fixed average frequency and is modulated at a frequency of a few kHz, with a variable modulation amplitude in the range of tens of MHz. The probe transmission is measured as a function of the detuning of the coupling laser from the Rydberg resonance. The first-harmonic demodulated EIT signal has two peaks that are, in the case of large modulation amplitude, separated by the peak-to-peak modulation amplitude of the probe laser times a scaling factor λ p / λ c , where λ p and λ c are the probe- and coupling-laser wavelengths. The scaling factor is due to Doppler shifts in the EIT geometry. Second-harmonic demodulated EIT signals, obtained with small modulation amplitudes, yield spectral lines that are much narrower than corresponding lines in the modulation-free EIT spectra. The resultant spectroscopic resolution enhancement is conducive to improved measurements of radio-frequency (RF) fields based on Rydberg-atom EIT, an approach in which the response of Rydberg atoms to RF fields is exploited to characterize RF fields. Here, we employ wavelength modulation spectroscopy to reduce the uncertainty of atom-based frequency and field measurement of an RF field in the VHF radio band.