Abstract We introduce a method to measure radio frequency (RF) electric fields (E-fields) using atoms contained in a prism-shaped vapor cell. The method utilizes the concept of electromagnetically induced transparency with Rydberg atoms. The RF E-field induces changes in the index of refraction of the vapor resulting in deflection of the probe laser beam as it passes through the prism-shaped vapor cell. We measured a minimum RF E-field of 8.25 μ Vcm − 1 with a sensitivity of ∼ 46.5 μ Vcm − 1 Hz − 1 / 2 . The experimental results agree with a numerical model that includes dephasing effects. We discuss possible improvements to obtain higher sensitivity for RF E-field measurements.
Abstract We introduce a method to measure radio frequency (RF) electric fields (E-fields) using atoms contained in a prism-shaped vapor cell. The method utilizes the concept of electromagnetically induced transparency with Rydberg atoms. The RF E-field induces changes in the index of refraction of the vapor resulting in deflection of the probe laser beam as it passes through the prism-shaped vapor cell. We measured a minimum RF E-field of 8.25 μ Vcm − 1 with a sensitivity of ∼ 46.5 μ Vcm − 1 Hz − 1 / 2 . The experimental results agree with a numerical model that includes dephasing effects. We discuss possible improvements to obtain higher sensitivity for RF E-field measurements.
Atom-based measurements of length, time, gravity, inertial forces and electromagnetic fields are receiving increasing attention. Atoms possess properties that suggest clear advantages as self calibrating platforms for measurements of these quantities. In this review, we describe work on a new method for measuring radio frequency (RF) electric fields based on quantum interference using either Cs or Rb atoms contained in a dielectric vapor cell. Using a bright resonance prepared within an electromagnetically induced transparency window it is possible to achieve high sensitivities, <1 μ V cm −1 Hz −1/2 , and detect small RF electric fields μ V cm −1 with a modest setup. Some of the limitations of the sensitivity are addressed in the review. The method can be used to image RF electric fields and can be adapted to measure the vector electric field amplitude. Extensions of Rydberg atom-based electrometry for frequencies up to the terahertz regime are described.
Significant progress has been made in atom-based measurements of length, time, gravity and electromagnetic fields in recently years. Rydberg atom-based microwave electric field measurement, using electromagnetically induced transparency (EIT) in room temperature alkali-metal vapors, has been extensively investigated and aroused the broad interest. This approach may establish a new standard for the measurements of microwave (MW) and radio frequency (RF) electric fields.In this review, we describe the work on a new method of measuring electric fields based on quantum interference by using either cesium or rubidium atoms contained in a dielectric vapor cell. Rydberg atoms with principal quantum number n >>1 have large direct current (DC) polarizabilities and microwave transition dipole moments, thereby making them extremely sensitive to external electric fields. Using the Rydberg three-level EIT to detect the level splitting and shift that is induced by the external field, we can realize a rapid and robust self-calibration method of measuring the electric field in a frequency range from 0.01 GHz to 1000 GHz. For the MW electric field (frequency range > 1 GHz), the MW field causes the Rydberg states to split, known as an Autler-Townes splitting (A-T) effect when the applied microwave can resonate with adjacent Rydberg states. The MW coupled A-T splitting is proportional to the applied electric field strength, from which the field strength is measured. Using the EIT window, a high sensitivity of 3 μV·cm-1·Hz-1/2 and small electric field of 1 μV/cm are expected to be achieved with a modest setup, and the limitations of the sensitivity are also addressed in the review. For the RF field at frequency mj EIT lines, and avoided crossings formed with the fine-structure levels of equal mj and different J's, which is used to calibrate and measure the RF field amplitude. On the other hand, the dependence of the EIT-line strength on the RF field polarization provides a fast and robust polarization measurement of RF fields based on matching experimental data with a theoretical simulation. The measurements of minimum strengths and sensitivity of RF fields based on Rydberg atoms are one order magnitude below the values obtained by traditional antenna methods. The atom-based field measurement paves the way for determining fields through calibration-free, invariable atomic properties and miniaturization. We also propose its various potential applications in the future.
Traceable radio-frequency electric field measurements with high sensitivity have been demonstrated from the centimeter wave to the millimeter wave using room-temperature Rydberg atoms. Here, we investigate the splitting spectra of electromagnetically induced transparency induced by a radio-frequency electric field, which is detuned from the resonant frequency of transitions between two Rydberg states, 47D 5/2 ↔ 48P 3/2 . By varying the detuning of the radio-frequency electric field, we measure the separation between the two peaks, and in particular their relative height. The resulting measured resonant transition frequency between two Rydberg states is found to exhibit a visible change when the power of the radio-frequency electric field is varied, thus causing uncertainty in the traceable radio-frequency electric field measurement. Further, the effect of detuning of the probe light on the radio-frequency electric field measurement is presented.
An atom-based approach is presented to detect absolute microwave (MW) electric fields (E-fields). The approach uses Rydberg atoms in vapor cells at room temperature. The MW E-field measurements utilize a bright resonance prepared within an electromagnetically induced transparency (EIT) window. The large transition dipole moments between energetically adjacent Rydberg states enable this method to make traceable E-field measurements with a sensitivity that is several orders of magnitude higher than the current standard for MW E-field measurements. The method can be used to image MW E-field in the near field regime with a subwavelength resolution of mathrmlambdaMW/650, where mathrmlambdaMW is the wavelength of the MW E-field. A high accuracy of $\\mathrm{1\\%}$ has been reached by minimizing the effects of the vapor cell geometry on the measured MW E-field. The dissertation also presents an alternative technique to perform the MW E-field measurement using dispersive properties of the EIT spectrum with a prism vapor cell. Recently, we applied a homodyne detection technique with a Mach Zehnder interferometer to achieve a new sensitivity limit for the MW E-field measurement, mathrmsim3muVcm−1Hz−1/2. The new sensitivity is one order of magnitude better than our prior best sensitivity presented in Ref. [Nat. Phys. 8, 819 (2012)]. The Rydberg atom-based method is promising to be a new standard for MW E-field measurements and to develop into portable devices in the field of MW technologies.
We investigate a technique for detecting radio frequency (RF) electric fields in a cesium (Cs) vapor cell at room temperature by collecting charges from ionized Rydberg atoms and compare its performance with the established method of electromagnetically induced transparency (EIT). By applying a known RF field, we measure the response from both the electrical (ionization current-based) and optical (EIT-based) readouts. The ionization current-based method yields a sensitivity of 22 μ V m−1 Hz−1/2, while the EIT-based method achieves 3.7 μ V m−1 Hz−1/2. The sensitivity of the ionization current-based method is limited by the 2.2 k Ω resistance between the collection electrodes, attributed to a thin Cs film on the inner surfaces of the vapor cell. Controlling or eliminating the Cs layer can significantly improve the sensitivity of this ionization approach.
Abstract The Rydberg atom can be used as an active probe for precision radio-frequency (RF) electric field (E-field) measurement; however, the RF cavity resonance and scattering effect of an atomic vapor cell lead to polarization distortion inside the cell, and the depolarization effect limits the sensitivity and accuracy of E-field measurement. The finite element simulation and characteristic mode analysis of a hollow-cavity model are implemented to find an optimized solution of minimizing such depolarization. Manipulating atoms in the middle layer of a vapor cell along an incident field vector can avoid the depolarization, which is validated by the vector distribution measurement at 15.09 GHz.