Adiabatic quantum-flux-parametron (AQFP) logic is an energy-efficient superconductor logic family. In this paper, we conducted the high-frequency operation and energy measurement of an AQFP circuit with more than 1000 Josephson junctions in the experiment. We designed an 8-bit carry look-ahead adder (CLA) using AQFP gates and fabricated it using an advanced fabrication technology, the AIST 10 kA/cm2 Nb high-speed standard process. The correct operation of the 8-bit CLA was demonstrated at a 1-GHz clock frequency for a critical carry propagation test vector. The energy dissipation of the 8-bit CLA was measured by observing the power of excitation current. Our results showed that the energy dissipation per operation of the 8-bit CLA can be estimated to be approximately 1.5 aJ, or 24kBT per junction, where kB is the Boltzmann constant and T is the operating temperature.
Adiabatic quantum-flux-parametron (AQFP) logic is an energy-efficient superconductor logic family. In this paper, we conducted the high-frequency operation and energy measurement of an AQFP circuit with more than 1000 Josephson junctions in the experiment. We designed an 8-bit carry look-ahead adder (CLA) using AQFP gates and fabricated it using an advanced fabrication technology, the AIST 10 kA/cm2 Nb high-speed standard process. The correct operation of the 8-bit CLA was demonstrated at a 1-GHz clock frequency for a critical carry propagation test vector. The energy dissipation of the 8-bit CLA was measured by observing the power of excitation current. Our results showed that the energy dissipation per operation of the 8-bit CLA can be estimated to be approximately 1.5 aJ, or 24kBT per junction, where kB is the Boltzmann constant and T is the operating temperature.
Adiabatic quantum-flux-parametron (AQFP) logic is a superconductor logic family that can operate with low switching energy due to adiabatic switching. In a previous study, we proposed a low-latency clocking scheme called delay-line clocking, in which the latency for each logic operation is determined by the propagation delay of the excitation current. We demonstrated several AQFP logic gates with delay-line clocking and demonstrated a phase skipping operation, in which some of the AQFP buffers for phase synchronization are removed to reduce the junction count and energy dissipation. In the present study, we design and demonstrate an AQFP 8-bit ripple carry adder with delay-line clocking to show that delay-line clocking and the phase skipping operation are applicable to large-scale AQFP circuits. The latency of this adder is 960 ps, which is 40% of that for a conventional design. Moreover, due to the phase skipping operation, the junction count is reduced to approximately 70% of that for the conventional design. We find that this adder can operate at up to 4 GHz. The above results indicate that large-scale AQFP circuits can operate with low latency and low junction count by using delay-line clocking and a phase skipping operation.
We have been investigating an ultra-low-power adiabatic quantum-flux-parametron (AQFP) logic, the energy dissipation of which can be decreased by changing its potential energy slowly or adiabatically. In the present study, we designed basic AQFP logic gates and an AQFP 1-bit full adder, and examined their operations through simulations and experiments. The AQFP 1-bit full adder is composed of 46 Josephson junctions, which is approximately one-quarter the number of junctions of a full adder using conventional rapid single-flux-quantum logic. The measurement results indicated that the AQFP 1-bit full adder has a wide current bias margin of as large as ±27.8%.
Complementary metal-oxide-semiconductor (CMOS) circuit technology has sustainedthe exponential growth of computing power for more than 20 years. However, it hasbeen estimated that the power consumption of a next-generation supercomputer willexceed the power supplied from a single power plant. This indicates the need to dramaticallyimprove the energy efficiency of logic devices to achieve future high-endcomputers.As an extremely energy-efficient logic, we proposed and have been investigatingadiabatic quantum-flux-parametron (AQFP) devices. Due to adiabatic switching operations,its bit energy (energy dissipation per bit) can go below Ic 0, where Ic is acritical current of a Josephson junction and 0 is a single-flux-quantum (SFQ). Ic 0corresponds to the energy dissipated at every 2 phase transition in conventional nonadiabaticsuperconductor logics.We have two objectives in this study. One is to reveal physical energy bounds oncomputation through investigation of the energy efficiency of AQFP logic. The otheris to develop fundamental circuits necessary for energy-efficient computing systemsusing AQFP logic.First, we numerically and experimentally demonstrated the sub-Ic 0 bit-energyoperations of AQFP gates to show that AQFP gates operate in adiabatic modes. Weinvestigated the dependence of energy dissipation and operation margins on circuitparameters. After optimizing the parameters, we calculated the bit energy and the biterror rate at 4.2 K to verify the sub-Ic 0 bit-energy operations at a finite temperature.Additionally, we measured the bit energy of an AQFP gate using a superconductorresonator-based method.Secondly, we numerically demonstrated the sub-kBT bit-energy operations, wherekB is the Boltzmann constant and T is temperature, to show that AQFP gates can operatebeyond thermodynamic energy bounds. We investigated the dependence of energydissipation on operation frequencies and damping conditions of Josephson junctions.By using underdamped junctions, we confirmed the sub-kBT bit-energy operationsat a finite temperature thorough circuit simulation. This result indicates that thereis no minimum energy dissipation required for the operations of AQFP gates unlessthe entropy of the system decreases, which corresponds to the Landauer’s argument on the minimum energy dissipation for computation. Also, we discussed quantummechanicalenergy bounds and experimentally demonstrated AQFP gates with underdampedjunctions.Additionally, we investigated reversible computing using AQFP logic with underdampedjunctions, in order to deal with an important but unresolved question: “Isreversible computing achievable by using practical devices?” We built a purely reversiblegate by using AQFP gates, which we designated as the reversible quantumflux-parametron (RQFP) gate. We calculated its energy dissipation and confirmed thatthere is no minimum energy dissipation for reversible logic operations using RQFPgates. To the best of our knowledge, these are the first calculation results that show nominimum energy dissipation in reversible computing that use practical circuit structures.Moreover, our experimental results have demonstrated the logical and physicalreversibility of the RQFP gate. We believe that this is the first demonstration thatshows both logical and physical reversibility using practical devices.Finally, we proposed a novel energy-efficient latch for AQFP logic, which we designatedas the quantum-flux-latch (QFL). Latches are necessary circuitries in largecomputing systems but had been missing in AQFP logic. We discussed its energyefficiency through simulation and experimentally demonstrated correct operations ofthe QFL and a 1-bit shift register using QFLs. Also, we proposed high-speed test circuitsusing QFLs and experimentally demonstrated logic operations of AQFP circuitsat high speed.We strongly believe that our results showed the extremely high energy efficiency ofAQFP logic. These results will move the AQFP logic to practical usage as extremelyenergy-efficient integrated circuits.
Adiabatic quantum-flux-parametron (AQFP) logic is an emerging superconducting circuit technology, which is superior in terms of energy dissipation at reasonable clock frequencies. Although multiplication is important for signal or image processing applications, such as fast Fourier transform processors or GPUs, no multipliers implemented in AQFP logic have been demonstrated yet. In this article, we introduce two types of algorithms to calculate multiplication results: array type and Wallace-tree type. We design 4-bit multipliers based on these algorithms using the AIST 10 kA/cm2high-speed standard process and compare these circuits in terms of the following metrics: number of Josephson junctions, circuit latency, area, and power dissipation. As a result, in all respects, the Wallace-tree type is better than the array type. In addition, we experimentally confirm that the fabricated chips containing both types of multipliers are operating correctly at 100 kHz for all test patterns, including random patterns. This is the first time AQFP multipliers have been experimentally demonstrated completely.
Abstract Superconductor logic families can operate with small power dissipation and are thus suitable as building blocks for various computing systems. In some applications, superconductor logic circuits should be designed using Josephson junctions with low I c values ( I c : critical current). For instance, lowering I c values enables qubit interface circuits to operate with very small power dissipation at ~10 mK and stochastic electronics to easily induce stochastic operations. In this study, we develop the AIST 1 kA cm −2 Nb planarized process (1KP) with a minimum critical current of 10 µA, dedicated to the design of qubit interface circuits and stochastic electronics. We also develop rapid single-flux-quantum (RSFQ) and adiabatic quantum-flux-parametron (AQFP) cell libraries using the 1KP. The power dissipation of RSFQ logic using the 1KP can be reduced to 3.2% of that for conventional RSFQ logic by reducing both I c values and a bias voltage. Furthermore, the amount of supply currents for AQFP circuits using the 1KP can be reduced to ~40% of that for conventional AQFP circuits due to a large mutual inductance between AQFP gates and excitation lines, which results from a reduction in I c and an increase in inductances. We demonstrate RSFQ and AQFP circuits fabricated by the 1KP at 4.2 K. These results indicate that RSFQ and AQFP circuits using the 1KP have the potential to be used for the design of qubit interface circuits and stochastic electronics.
Adiabatic quantum-flux-parametron (AQFP) is an energy-efficient superconductor logic. The advantage of AQFP is that the switching energy can be reduced by lowering operation frequencies or by increasing the quality factors of Josephson junctions, while keeping the energy barrier height much larger than thermal energy. In other words, both low energy dissipation and low bit error rates (BERs) can be achieved. In this paper, we report the first measurement results of the low BERs of AQFP logic. We used a superconductor voltage driver with a stack of dc superconducting-quantum-interference-devices to amplify the logic signals of AQFP gates into mV-range voltage signals for the BER measurement. Our measurement results showed 3.3 dB and 2.6 dB operation margins, in which BERs were less than 10−20, for 1 Gbps and 2 Gbps data rates, respectively. While the observed BERs were very low, the estimated switching energy for the 1-Gbps operation was only 2 zJ or 30kBT, where kB is the Boltzmann's constant and T is the temperature. Unlike conventional non-adiabatic logic, BERs are not directly associated with switching energy in AQFP.