Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Optics

Suppressing residual amplitude modulation to the 10−7 level in optical phase modulation

Jin Bi, Yunlin Zhi, Liufeng Li, Lisheng Chen

Published Jan 16, 2019• 38 citations
Publisher

Abstract

Residual amplitude modulation is one of the major stability-degrading factors in many precision measurements. Using an electro-optic (EO) crystal with wedged input and output surfaces is an effective way to suppress residual amplitude modulation. Here the mechanism of residual amplitude modulation in this approach is investigated. The residual amplitude modulations measured in standard and wedged EO crystals bear similarities in their temperature and polarization dependences, implying that a mixture of the two orthogonal polarizations in the extraordinary light is responsible for the residual amplitude modulation in the wedged EO crystal. Similar to a standard EO crystal, a non-uniform spatial distribution of residual amplitude modulation is also observed in the extraordinary light emerging from the wedged EO crystal. The optical isolator after the EO crystal is replaced by a Faraday rotator, and an improvement in the long-term stability is observed. With the wedged-crystal approach, residual amplitude modulation as low as 2×10−7 is observed, contributing a frequency instability of 8×10−18 (500 s) in Pound–Drever–Hall frequency stabilization with a discrimination slope of 1×10−4 V/Hz.

DOI
10.1364/ao.58.000690

Related papers

Measurement and control of residual amplitude modulation in optical phase modulation

Liufeng Li, Fang Liu, Wang Chun +1 more

Residual amplitude modulation is one of the major sources of instability in ultra-sensitive optical detections based on frequency modulation. Using a MgO·LiNbO(3) electro-optic crystal, we systematically measure the temperature and polarization dependence of residual amplitude modulation and our experimental results are in good agreement with a previous theoretical analysis. After optical phase modulation, two independent arms including optical detection and frequency demodulation are employed to closely examine the instability of the residual amplitude modulation. Residual amplitude modulation below 25 ppm is obtained with an active cancellation scheme in which the crystal temperature is varied so as to zero the baseline drifts with different origins. Possible improvements for better suppression and stability are discussed.

Review of Scientific Instruments•Apr 1, 2012•77 citations

Reduction of zero baseline drift of the Pound–Drever–Hall error signal with a wedged electro-optical crystal for squeezed state generation

Zhixiu Li, Weiguang Ma, Wenhai Yang +2 more

as the modulation crystal to reduce the zero baseline drift (ZBD) of the Pound-Drever-Hall (PDH) error signal. When the input linear polarization is not along the modulation direction, the wedged design can separate the two orthogonal polarizations in space after the EOM and eliminate the interference between the carrier and the two orthogonal sidebands. Therefore, the residual amplitude modulation (RAM) of phase modulation process caused by the input polarization misalignment and the etalon effect can be significantly reduced. The noise power spectrum of phase-modulated light with wedged crystal EOM is suppressed from -24 to -69 dBm, which is much lower than that with conventional EOM. The peak-to-peak value of the ZBD of the PDH error signal is reduced effectively to +70/-50 ppm during the 10 h, which meets the requirements for stable squeezed light generation.

Optics Letters•Jul 12, 2016•66 citations

Artificial modulation-free Pound–Drever–Hall method for laser frequency stabilization

H. M. Wang, Zitong Xu, S. C. Ma +3 more

We have proposed an artificial modulation-free Pound-Drever-Hall (PDH) method for laser frequency stabilization and demonstrated it via two-color polarization spectroscopy of Rydberg electromagnetically induced transparency (EIT) resonance in a room-temperature rubidium vapor. Due to the unique error signal profile, the conventional PDH method owns a large capture range in laser frequency locking. Here we manually construct a PDH error signal via a linear combination of polarization spectroscopies of the Rydberg EIT resonances without and with a magnetic field applied. The artificial modulation-free PDH error signal owns a subnatural linewidth dispersion curve as well as a large capture range with which we successfully stabilize the laser to an absolute atomic frequency reference in a long running time, immune to environmental fluctuation and even manmade impulse perturbation. This method can provide an absolute frequency reference based on atomic transition while keeping similar locking ability to provide corrections for frequency fluctuations over a broad bandwidth as the conventional PDH.

Optics Letters•Nov 27, 2019•19 citations

Characterization of a Two-Photon Rubidium-87 Optical Clock

Sophia Rojas

Atomic clocks are based on highly stable and well-characterized atomic transitions, mak-ing precise control and understanding of systematic frequency shifts essential for improved timekeeping performance. This thesis presents an experimental study of light-induced Stark shifts in rubidium and their impact on precision laser spectroscopy relevant to atomic frequency standards, as well as the effects of residual amplitude modulation on the laser lock point and the resulting sensitivity of both short- and long-term stability. A laser-based spectroscopy system was developed to probe rubidium transitions while enabling controlled variation of optical intensity. The optical beam was experimentally characterized through calculations of beam waist and measurements of power to accurately determine the intensity at the interaction region. Frequency shifts arising from the AC Stark effect were measured as a function of optical power, allowing extraction of the differential polarizability between atomic energy levels using a theoretical model relating energy shifts to electric-field intensity. Uncertainty analysis was performed through systematic propagation of experimental errors associated with beam geometry, optical power calibration, and frequency measurements. In addition, residual amplitude modulation generated by electro-optic phase modulation was investigated as a significant source of systematic error in frequency stabilization systems used in atomic clocks. The magnitude and behavior of RAM were experimentally characterized, and its impact on frequency stability was quantified by measuring the sensitivity of the laser lock point to controlled variations in RAM. Potential mitigation strategies were then explored through active pre-compensation of RAM using an amplitude electro-optic modulator in a closed-loop feedback system.

•Jan 1, 2026•0 citations

Reducing residual amplitude modulation in electro-optic phase modulators by erasing photorefractive scatter

Juna Sathian, Esa A. Jaatinen

Residual amplitude modulation (RAM) is an unwanted noise source in electro-optic phase modulators. The analysis presented shows that while the magnitude of the RAM produced by a MgO:LiNbO(3) modulator increases with intensity, its associated phase becomes less well defined. This combination results in temporal fluctuations in RAM that increase with intensity. This behavior is explained by the presented phenomenological model based on gradually evolving photorefractive scattering centers randomly distributed throughout the optically thick medium. This understanding is exploited to show that RAM can be reduced to below the 10(-5) level by introducing an intense optical beam to erase the photorefractive scatter.

Optics Express•May 13, 2013•25 citations

Pound-Drever-Hall Feedforward for Trapped-Ion Optical Qubits

Jia-Yang Gao, Jianwei Lee, Morteza Ahmadi +1 more

Laser phase noise is one of the limiting factors that dictate gate fidelities and coherence times in trapped-ion quantum systems. Previous studies have reported that when the Rabi frequency of an ion qubit is close to the servo-bump phase-noise frequency, the driving laser limits the fidelity and coherence time. This issue has typically been mitigated by choosing a Rabi frequency outside the servo-bump region. However, this constrains the usable range of gate speeds and can limit the achievable fidelity. To address this issue, we developed an active phase-noise stabilization system for a barium-ion optical-qubit laser at 1762 nm, employing a fiber electro-optic modulator (EOM) with an electrical feedforward servo. Our results demonstrate that this setup, based on the Pound-Drever-Hall (PDH) feedforward method, can suppress servo-bump phase noise by 15 dB near the bump peak frequency in our locking system. The laser phase noise is analyzed using delayed self-heterodyne interferometry (DSHI). We further tested the stabilized laser on an optical qubit and observed a clear improvement in coherence time based on the measured amplitude decay of Rabi oscillations, even when the Rabi frequency lies within the servo-bump bandwidth. This technique can be readily adapted to other optical qubits with minimal modifications.

quant-pharXiv:2607.24050•Jul 28, 2026•0 citations
Residual amplitude modulation is one of the major stability-degrading factors in many precision measurements. Using an electro-optic (EO) crystal with wedged input and output surfaces is an effective way to suppress residual amplitude modulation. Here the mechanism of residual amplitude modulation in this approach is investigated. The residual amplitude modulations measured in standard and wedged EO crystals bear similarities in their temperature and polarization dependences, implying that a mixture of the two orthogonal polarizations in the extraordinary light is responsible for the residual amplitude modulation in the wedged EO crystal. Similar to a standard EO crystal, a non-uniform spatial distribution of residual amplitude modulation is also observed in the extraordinary light emerging from the wedged EO crystal. The optical isolator after the EO crystal is replaced by a Faraday rotator, and an improvement in the long-term stability is observed. With the wedged-crystal approach, residual amplitude modulation as low as 2×10−7 is observed, contributing a frequency instability of 8×10−18 (500 s) in Pound–Drever–Hall frequency stabilization with a discrimination slope of 1×10−4 V/Hz.
Residual amplitude modulation is one of the major sources of instability in ultra-sensitive optical detections based on frequency modulation. Using a MgO·LiNbO(3) electro-optic crystal, we systematically measure the temperature and polarization dependence of residual amplitude modulation and our experimental results are in good agreement with a previous theoretical analysis. After optical phase modulation, two independent arms including optical detection and frequency demodulation are employed to closely examine the instability of the residual amplitude modulation. Residual amplitude modulation below 25 ppm is obtained with an active cancellation scheme in which the crystal temperature is varied so as to zero the baseline drifts with different origins. Possible improvements for better suppression and stability are discussed.
as the modulation crystal to reduce the zero baseline drift (ZBD) of the Pound-Drever-Hall (PDH) error signal. When the input linear polarization is not along the modulation direction, the wedged design can separate the two orthogonal polarizations in space after the EOM and eliminate the interference between the carrier and the two orthogonal sidebands. Therefore, the residual amplitude modulation (RAM) of phase modulation process caused by the input polarization misalignment and the etalon effect can be significantly reduced. The noise power spectrum of phase-modulated light with wedged crystal EOM is suppressed from -24 to -69 dBm, which is much lower than that with conventional EOM. The peak-to-peak value of the ZBD of the PDH error signal is reduced effectively to +70/-50 ppm during the 10 h, which meets the requirements for stable squeezed light generation.
We have proposed an artificial modulation-free Pound-Drever-Hall (PDH) method for laser frequency stabilization and demonstrated it via two-color polarization spectroscopy of Rydberg electromagnetically induced transparency (EIT) resonance in a room-temperature rubidium vapor. Due to the unique error signal profile, the conventional PDH method owns a large capture range in laser frequency locking. Here we manually construct a PDH error signal via a linear combination of polarization spectroscopies of the Rydberg EIT resonances without and with a magnetic field applied. The artificial modulation-free PDH error signal owns a subnatural linewidth dispersion curve as well as a large capture range with which we successfully stabilize the laser to an absolute atomic frequency reference in a long running time, immune to environmental fluctuation and even manmade impulse perturbation. This method can provide an absolute frequency reference based on atomic transition while keeping similar locking ability to provide corrections for frequency fluctuations over a broad bandwidth as the conventional PDH.
Atomic clocks are based on highly stable and well-characterized atomic transitions, mak-ing precise control and understanding of systematic frequency shifts essential for improved timekeeping performance. This thesis presents an experimental study of light-induced Stark shifts in rubidium and their impact on precision laser spectroscopy relevant to atomic frequency standards, as well as the effects of residual amplitude modulation on the laser lock point and the resulting sensitivity of both short- and long-term stability. A laser-based spectroscopy system was developed to probe rubidium transitions while enabling controlled variation of optical intensity. The optical beam was experimentally characterized through calculations of beam waist and measurements of power to accurately determine the intensity at the interaction region. Frequency shifts arising from the AC Stark effect were measured as a function of optical power, allowing extraction of the differential polarizability between atomic energy levels using a theoretical model relating energy shifts to electric-field intensity. Uncertainty analysis was performed through systematic propagation of experimental errors associated with beam geometry, optical power calibration, and frequency measurements. In addition, residual amplitude modulation generated by electro-optic phase modulation was investigated as a significant source of systematic error in frequency stabilization systems used in atomic clocks. The magnitude and behavior of RAM were experimentally characterized, and its impact on frequency stability was quantified by measuring the sensitivity of the laser lock point to controlled variations in RAM. Potential mitigation strategies were then explored through active pre-compensation of RAM using an amplitude electro-optic modulator in a closed-loop feedback system.
Residual amplitude modulation (RAM) is an unwanted noise source in electro-optic phase modulators. The analysis presented shows that while the magnitude of the RAM produced by a MgO:LiNbO(3) modulator increases with intensity, its associated phase becomes less well defined. This combination results in temporal fluctuations in RAM that increase with intensity. This behavior is explained by the presented phenomenological model based on gradually evolving photorefractive scattering centers randomly distributed throughout the optically thick medium. This understanding is exploited to show that RAM can be reduced to below the 10(-5) level by introducing an intense optical beam to erase the photorefractive scatter.
Laser phase noise is one of the limiting factors that dictate gate fidelities and coherence times in trapped-ion quantum systems. Previous studies have reported that when the Rabi frequency of an ion qubit is close to the servo-bump phase-noise frequency, the driving laser limits the fidelity and coherence time. This issue has typically been mitigated by choosing a Rabi frequency outside the servo-bump region. However, this constrains the usable range of gate speeds and can limit the achievable fidelity. To address this issue, we developed an active phase-noise stabilization system for a barium-ion optical-qubit laser at 1762 nm, employing a fiber electro-optic modulator (EOM) with an electrical feedforward servo. Our results demonstrate that this setup, based on the Pound-Drever-Hall (PDH) feedforward method, can suppress servo-bump phase noise by 15 dB near the bump peak frequency in our locking system. The laser phase noise is analyzed using delayed self-heterodyne interferometry (DSHI). We further tested the stabilized laser on an optical qubit and observed a clear improvement in coherence time based on the measured amplitude decay of Rabi oscillations, even when the Rabi frequency lies within the servo-bump bandwidth. This technique can be readily adapted to other optical qubits with minimal modifications.