© 2026 Aqora Quantum S.A.S.

Terms Privacy Legal Notice

Advanced Photon Counting Techniques

Design of efficient superconducting nanowire single photon detectors for near-infrared wavelengths

M. J. A. de Dood

Published May 14, 2018• 0 citations

Abstract

Superconducting single photon detectors consist of a narrow and thin wire of superconductor and can detect single photons with high efficiency and high speed. Simultaneous optimization of the detection efficiency and detector response time is difficult because the response time is set by the dimensions of the wire (cross section and length) while the detection efficiency is determined by both the internal detection mechanism and the dimensions of the wire. Wider and shorter wires are easier to fabricate, are more robust and lead to shorter detector reset time, but are generally less efficient. Experiments employing detector tomography provide important insights into the photon detection mechanism and indicate a detection mechanism where the edges of the wire are more efficient. This leads to a position dependent local detection efficiency that can be explained in the context of a photon-assisted-vortex-entry model and predicts an optimum wire width ~70 nm. A 50 nm wide silicon nanowire deposited on top of a 150 nm wide NbN nanowire directs light at 1550 nm wavelength to the edges and improves both the total absorption efficiency and the internal detection efficiency of the wire. The total absorption efficiency can be enhanced by 30% while the internal detection efficiency is increased by 70%. Assuming that the wire covers a similar area the detector response time is reduced 4-fold compared to the standard design using a 70 nm wide wire.

DOI: 10.1117/12.2307635

Related papers

Design of NbN superconducting nanowire single photon detectors with enhanced infrared photon detection efficiency

Q. Wang, Jelmer J. Renema, Andreas Engel +1 more

Nanowire superconducting single-photon detectors (SSPDs) consist of a superconducting wire of nanoscale cross-section [1], typically 4×100 nm2. A current close to the device critical current renders the nanowire sensitive to single photons. SSPDs are known for their high efficiency, low jitter, low dark count rate and fast reset time. An important challenge for future application of SSPDs is to extend the useful wavelength range towards the infrared without comprising detector speed or dark count rate. To this end, we explore optical designs with wider nanowires that utilize efficient detection of single photons at the edge of the nanowire. Silicon nanowires on top of a NbN nanowire increase both the calculated total absorption and the internal detection efficiency significantly compared to a standard meandering wire geometry.

arXiv:1612.02840•Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jan 1, 2017•1 citation

Intrinsic detection efficiency of superconducting nanowire single-photon detectors with different thicknesses

M. Hofherr, Dagmar Rall, K. Ilin +4 more

We evaluate experimentally the intrinsic detection efficiency (IDE) of superconducting NbN nanowire single-photon detectors in the range of wire thicknesses from 4 to 12 nm. The study is performed in the broad spectral interval between near-ultraviolet (wavelength 400 nm) and near-infrared (wavelength 2000 nm) light with plane waves at normal incidence. For visible light the IDE of the thinnest detectors reaches 70%. We use numerically computed absorptance of the nanowire-structures for the analysis of the experimental data. Variations in the detection efficiency with both the wire thickness and the wavelength evidence the red boundary of the hot-spot photon-detection mechanism. We explain the detection at larger wavelengths invoking thermal excitation of magnetic Pearl vortices over the potential barrier at the edges of the wire.

Journal of Applied Physics•Jul 1, 2010•94 citations

Design of NbN Superconducting Nanowire Single-Photon Detectors with Enhanced Infrared Detection Efficiency

Q. Wang, J. J. Renema, Andreas Engel +1 more

Superconducting nanowire single-photon detectors (SNSPDs) are important in quantum optics, secure communication, and even medical imaging. An SNSPD exhibits higher detection efficiency when a photon is absorbed near the edge of its wire, rather than in the middle. Combining insight from superconductor physics with nanophotonics, the authors show how to concentrate incident light on the edges of the nanowire, to enhance the efficiency and speed of next-generation detectors. This is expected to be particularly useful in the infrared range, for which there is presently no alternative SPD technology.

Physical Review Applied•Sep 8, 2017•13 citations

Mid-infrared characterization of NbTiN superconducting nanowire single-photon detectors on silicon-on-insulator

Adan Azem, D. Morozov, Daniel Kuznesof +4 more

Superconducting nanowire single-photon detectors are widely used for detecting individual photons across various wavelengths from ultraviolet to near-infrared range. Recently, there has been increasing interest in enhancing their sensitivity to single photons in the mid-infrared spectrum, driven by applications in quantum communication, spectroscopy, and astrophysics. Here, we present our efforts to expand the spectral detection capabilities of U-shaped NbTiN-based superconducting nanowire single-photon detectors, fabricated in a 2-wire configuration on a silicon-on-insulator substrate, into the mid-infrared range. We demonstrate saturated internal detection efficiency extending up to a wavelength of 3.5 μm for a 5 nm thick and 50 nm wide NbTiN nanowire with a dark count rate less than 10 counts per second at 0.9 K and a rapid recovery time of 4.3 ns. The detectors are engineered for integration on waveguides in a silicon-on-insulator platform for compact, multi-channel device applications.

arXiv:2408.15959•Applied Physics Letters•Nov 18, 2024•12 citations

NbN Nanowire Superconducting Single-Photon Detector for Mid-Infrared

Alexander A. Korneev, Yu. P. Korneeva, Irina Florya +2 more

Superconducting single-photon detectors (SSPD) is typically 100 nm-wide supercondiucting strip in a shape of meander made of 4-nm-thick ﬁlm. To reduce response time and increase voltage response a parallel connection of the strips was proposed. Recently we demonstrated that reduction of the strip width improves the quantum effciency of such a detector at wavelengths longer than 1.5 μm. Being encourage by this progress in quantum effciency we improved the fabrication process and made parallel-wire SSPD with 40-nm-wide strips covering total area of 10 μm x 10 μm. In this paper we present the results of the characterization of such a parallel-wire SSPD at 10.6 μm wavelength and demonstrate linear dependence of the count rate on the light power as it should be in case of single-photon response.

Physics Procedia•Jan 1, 2012•28 citations

Superconducting nanowire single-photon detectors at a wavelength of 940 nm

W. J. Zhang, Hao Li, Lixing You +9 more

We develop single-photon detectors comprising single-mode fiber-coupled superconducting nanowires, with high system detection efficiencies at a wavelength of 940 nm. The detector comprises a 6.5-nm-thick, 110-nm-wide NbN nanowire meander fabricated onto a Si substrate with a distributed Bragg reflector for enhancing the optical absorptance. We demonstrate that, via the design of a low filling factor (1/3) and active area (Φ = 10 μm), the system reaches a detection efficiency of ∼60% with a dark count rate of 10 Hz, a recovery time <12 ns, and a timing jitter of ∼50 ps.

arXiv:1506.07921•AIP Advances•Jun 1, 2015•7 citations

Superconducting single photon detectors consist of a narrow and thin wire of superconductor and can detect single photons with high efficiency and high speed. Simultaneous optimization of the detection efficiency and detector response time is difficult because the response time is set by the dimensions of the wire (cross section and length) while the detection efficiency is determined by both the internal detection mechanism and the dimensions of the wire. Wider and shorter wires are easier to fabricate, are more robust and lead to shorter detector reset time, but are generally less efficient. Experiments employing detector tomography provide important insights into the photon detection mechanism and indicate a detection mechanism where the edges of the wire are more efficient. This leads to a position dependent local detection efficiency that can be explained in the context of a photon-assisted-vortex-entry model and predicts an optimum wire width ~70 nm. A 50 nm wide silicon nanowire deposited on top of a 150 nm wide NbN nanowire directs light at 1550 nm wavelength to the edges and improves both the total absorption efficiency and the internal detection efficiency of the wire. The total absorption efficiency can be enhanced by 30% while the internal detection efficiency is increased by 70%. Assuming that the wire covers a similar area the detector response time is reduced 4-fold compared to the standard design using a 70 nm wide wire.

Nanowire superconducting single-photon detectors (SSPDs) consist of a superconducting wire of nanoscale cross-section [1], typically 4×100 nm2. A current close to the device critical current renders the nanowire sensitive to single photons. SSPDs are known for their high efficiency, low jitter, low dark count rate and fast reset time. An important challenge for future application of SSPDs is to extend the useful wavelength range towards the infrared without comprising detector speed or dark count rate. To this end, we explore optical designs with wider nanowires that utilize efficient detection of single photons at the edge of the nanowire. Silicon nanowires on top of a NbN nanowire increase both the calculated total absorption and the internal detection efficiency significantly compared to a standard meandering wire geometry.

We evaluate experimentally the intrinsic detection efficiency (IDE) of superconducting NbN nanowire single-photon detectors in the range of wire thicknesses from 4 to 12 nm. The study is performed in the broad spectral interval between near-ultraviolet (wavelength 400 nm) and near-infrared (wavelength 2000 nm) light with plane waves at normal incidence. For visible light the IDE of the thinnest detectors reaches 70%. We use numerically computed absorptance of the nanowire-structures for the analysis of the experimental data. Variations in the detection efficiency with both the wire thickness and the wavelength evidence the red boundary of the hot-spot photon-detection mechanism. We explain the detection at larger wavelengths invoking thermal excitation of magnetic Pearl vortices over the potential barrier at the edges of the wire.

Superconducting nanowire single-photon detectors (SNSPDs) are important in quantum optics, secure communication, and even medical imaging. An SNSPD exhibits higher detection efficiency when a photon is absorbed near the edge of its wire, rather than in the middle. Combining insight from superconductor physics with nanophotonics, the authors show how to concentrate incident light on the edges of the nanowire, to enhance the efficiency and speed of next-generation detectors. This is expected to be particularly useful in the infrared range, for which there is presently no alternative SPD technology.

Superconducting nanowire single-photon detectors are widely used for detecting individual photons across various wavelengths from ultraviolet to near-infrared range. Recently, there has been increasing interest in enhancing their sensitivity to single photons in the mid-infrared spectrum, driven by applications in quantum communication, spectroscopy, and astrophysics. Here, we present our efforts to expand the spectral detection capabilities of U-shaped NbTiN-based superconducting nanowire single-photon detectors, fabricated in a 2-wire configuration on a silicon-on-insulator substrate, into the mid-infrared range. We demonstrate saturated internal detection efficiency extending up to a wavelength of 3.5 μm for a 5 nm thick and 50 nm wide NbTiN nanowire with a dark count rate less than 10 counts per second at 0.9 K and a rapid recovery time of 4.3 ns. The detectors are engineered for integration on waveguides in a silicon-on-insulator platform for compact, multi-channel device applications.

Superconducting single-photon detectors (SSPD) is typically 100 nm-wide supercondiucting strip in a shape of meander made of 4-nm-thick ﬁlm. To reduce response time and increase voltage response a parallel connection of the strips was proposed. Recently we demonstrated that reduction of the strip width improves the quantum effciency of such a detector at wavelengths longer than 1.5 μm. Being encourage by this progress in quantum effciency we improved the fabrication process and made parallel-wire SSPD with 40-nm-wide strips covering total area of 10 μm x 10 μm. In this paper we present the results of the characterization of such a parallel-wire SSPD at 10.6 μm wavelength and demonstrate linear dependence of the count rate on the light power as it should be in case of single-photon response.

We develop single-photon detectors comprising single-mode fiber-coupled superconducting nanowires, with high system detection efficiencies at a wavelength of 940 nm. The detector comprises a 6.5-nm-thick, 110-nm-wide NbN nanowire meander fabricated onto a Si substrate with a distributed Bragg reflector for enhancing the optical absorptance. We demonstrate that, via the design of a low filling factor (1/3) and active area (Φ = 10 μm), the system reaches a detection efficiency of ∼60% with a dark count rate of 10 Hz, a recovery time <12 ns, and a timing jitter of ∼50 ps.