Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Investigation of the Harmonic Mixer and Low-Frequency Converter Regimes in a Superconducting Tunnel Junction

K. V. Kalashnikov, Anton A. Artanov, Gert J. de Lange, V. P. Koshelets

Published Feb 6, 2018• 6 citations
Publisher

Abstract

We experimentally investigate different mixing regi-mes in Nb/AlOx/Nb and Nb/AlN/NbN tunnel superconductor-insulator-superconductor (SIS) junctions. The SIS mixers were studied with regard to the following modes of operation: in an extremely low-frequency range (0.1-20 GHz) and as high harmonic mixers; n ≈ 20-30 at signal frequencies of about 500 GHz that requires high power of a local oscillator. The quasiparticle and Josephson mixing regimes have been compared. We demonstrate that, in some applications requiring high conversion efficiency, the Josephson regime can be more preferable than the quasiparticle regime due to a larger output signal and better signal-to-noise ratio. As an example of such an application, we consider the phase locking of a THz oscillator using a cryogenic harmonic phase detector, which only ought to realize all of its benefits under the Josephson mixing regime. In addition, we demonstrate that the presence of the Josephson effect results in considerable increase in conversion efficiency at the expense of the dynamic range decrease; it was measured for low-frequency up- and down-convertors, which are promising for cryogenic multiplexing systems.

DOI
10.1109/tasc.2018.2803043

Related papers

Investigation of the regimes of mixing of superconducting tunneling structures

K. V. Kalashnikov, Anton A. Artanov, Lyudmila V. Filippenko +1 more

The regimes of operation of a superconductor–insulator–superconductor tunnel junction based on three-layer structures Nb/AlOx/Nb and Nb/AlN/NbN as a harmonic mixer (for frequencies of the order of 600 and 20 GHz, respectively) and a frequency up-converter (in the frequency range from 0.1 to 5.0 GHz) have been investigated experimentally. The quasiparticle and Josephson mixing regimes have been compared. It has been shown that, in some practical applications, such as the use of the superconductor–insulator–superconductor junction as a cryogenic harmonic phase detector, the Josephson mixing regime is more preferable, because it can provide a higher signal and a greater signal-to-noise ratio as compared to the quasiparticle mixing regime. It has also been demonstrated that the Josephson mixing regime is promising for the use in signal multiplexing systems for superconducting detectors.

Physics of the Solid State•Nov 1, 2016•2 citations

High-frequency limits of superconducting tunnel junction mixers

Dag Winkler, T. Claeson

We have investigated high-frequency limits of superconducting quasiparticle mixers from experiments on Al/Al-oxide-In/Al (or Ag) tunnel junctions, and from calculations based on Tucker’s quantum theory of mixing (QTM). The small superconducting energy gap of Al enabled us to study mixer performance at around the junction gap frequency, fg =(Δ1+Δ2)/h≊87 GHz, of superconductor-insulator-superconductor (SIS) mixers, and at twice the junction gap frequency for S-I-normal metal (SIN) mixers ( fg =Δ1/h) with available millimeter wave sources. Because of the low transition temperature of Al (Tc ≊1.3 K), a dilution refrigerator was used for providing temperatures below 1 K. The best mixer conversion efficiency was obtained for a low-resistance (∼34 Ω) six-junction array SIS mixer operated at f/fg ≊1 (in this case 73 GHz). The coupled single sideband conversion gain (with no image rejection) was −13.8 dB and the available conversion gain was estimated to −8.4 dB. Complicating nonequilibrium phenomena made it difficult to compare the performance of these relatively high-current-density mixers to the QTM. However, good agreement between calculated and corresponding measured conversion efficiencies and dynamic resistance values was obtained for the low-current-density mixers. Noise due to switching between rf-induced Josephson steps and interference from Josephson mixing could be quenched by a magnetic field. Several high-frequency limits are considered in this paper (such as Josephson switching noise, nonequilibrium phenomena, pair breaking, and energy gap limitations). Our results indicate that submillimeter wave SIS mixer receivers are likely to perform well, at least up to their gap frequencies, i.e., the THz region for large gap superconductors. Our QTM calculations showed that conversion gain larger than unity should be possible up to twice the gap frequency. Above this frequency the conversion loss will increase rapidly.

Journal of Applied Physics•Dec 1, 1987•35 citations

Microwave mixing and direct detection using SIS and SIS' quasiparticle tunnel junctions

A. D. Smith, William R. McGrath, P. L. Richards +4 more

Quasiparticle mixers have shown strong quantum effects, conversion gain, and noise levels approaching the quantum limit, but only in tunnel junctions with very low sub-gap "leakage" conductance. It has been suggested that SIS' tunnel junctions, made from two different conductors with unequal gaps, will function as high gain mixers since the dynamic conductance below the gap is negative. We report results of the first SIS' mixing and direct detection experiments. At 36 GHz, a conversion efficiency of -4 dB with a noise temperature of 33 K (SSB) has been obtained. A novel gain mechanism for SIS' direct detectors is predicted. A direct detector responsivity of 250 A/W was measured. We compare our results to quantum theory models. In addition, we demonstrate quasiparticle harmonic mixing of a 36 GHz signal with an 18 GHz local oscillator in tin SIS junctions. Harmonic mixers can have important advantages at high microwave frequencies where insufficient local oscillator power is available.

IEEE Transactions on Magnetics•May 1, 1983•15 citations

Tunnel superconducting junctions for a cryogenic multiplexing system

Anton A. Artanov, K. V. Kalashnikov, V. P. Koshelets +1 more

the possibility of using superconductor–insulator–superconductor (SIS) tunnel junctions in a cryogenic multiplexing system for setting an ac current through arrays of transition edge sensors and reading out the received signal, as well as for setting a dc current through arrays of superconducting quantum interferometers is studied. Operation of the SIS frequency converter at relatively low (below 10 GHz) working frequencies is experimentally investigated. Different operation regimes are implemented; the conversion loss in the quasiparticle mode is found to be 8 dB and the output saturation power is–58 dBm. The possibility of up-conversion of several input signal frequencies simultaneously is demonstrated. It is shown that the SIS junction can be used as a current source controlled by an external RF signal.

Journal of Communications Technology and Electronics•Sep 1, 2016•1 citation

0.5-THz waveguide SIS mixers with NbN/AlN/NbN technology

Jing Li, Masanori Takeda, Zhen Wang +1 more

Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 29, 2007•3 citations

An experimental study of harmonic sis mixing at 205-235 ghz

Kecheng Xiao, Hideo Ogawa, Yasuo Fukui

A 230-GHz subharmonically pumped waveguide mixer employing superconducting tunnel junctions has been developed. We present, in this paper, an experimental study of harmonic superconductor-insulator-superconductor (SIS) mixing at 230 GHz, focusing mainly on its noise behavior. The mixer has a double-tuned waveguide structure and employs an array of four 1.7-/spl mu/m/sup 2/ Nb-AlOx-Nb SIS junctions in series, with /spl omega/R/sub n/C/sub j//spl sim/3 at 230 GHz. Harmonic quantum mixing occurred over an experimental frequency range of 205-235 GHz (local oscillator: 112.5-117.5 GHz), exhibiting corresponding double sideband noise temperatures of lower than 150 K, with a lowest value of 75 K at /spl sim/230 GHz. The measured mixer noise is believed to be the lowest yet reported for a mixer using subharmonic-pump configuration at this frequency. A phenomenon that we attribute to the third harmonic SIS mixing has also been observed.

IEEE Transactions on Applied Superconductivity•Dec 1, 2003•3 citations
We experimentally investigate different mixing regi-mes in Nb/AlOx/Nb and Nb/AlN/NbN tunnel superconductor-insulator-superconductor (SIS) junctions. The SIS mixers were studied with regard to the following modes of operation: in an extremely low-frequency range (0.1-20 GHz) and as high harmonic mixers; n ≈ 20-30 at signal frequencies of about 500 GHz that requires high power of a local oscillator. The quasiparticle and Josephson mixing regimes have been compared. We demonstrate that, in some applications requiring high conversion efficiency, the Josephson regime can be more preferable than the quasiparticle regime due to a larger output signal and better signal-to-noise ratio. As an example of such an application, we consider the phase locking of a THz oscillator using a cryogenic harmonic phase detector, which only ought to realize all of its benefits under the Josephson mixing regime. In addition, we demonstrate that the presence of the Josephson effect results in considerable increase in conversion efficiency at the expense of the dynamic range decrease; it was measured for low-frequency up- and down-convertors, which are promising for cryogenic multiplexing systems.
The regimes of operation of a superconductor–insulator–superconductor tunnel junction based on three-layer structures Nb/AlOx/Nb and Nb/AlN/NbN as a harmonic mixer (for frequencies of the order of 600 and 20 GHz, respectively) and a frequency up-converter (in the frequency range from 0.1 to 5.0 GHz) have been investigated experimentally. The quasiparticle and Josephson mixing regimes have been compared. It has been shown that, in some practical applications, such as the use of the superconductor–insulator–superconductor junction as a cryogenic harmonic phase detector, the Josephson mixing regime is more preferable, because it can provide a higher signal and a greater signal-to-noise ratio as compared to the quasiparticle mixing regime. It has also been demonstrated that the Josephson mixing regime is promising for the use in signal multiplexing systems for superconducting detectors.
We have investigated high-frequency limits of superconducting quasiparticle mixers from experiments on Al/Al-oxide-In/Al (or Ag) tunnel junctions, and from calculations based on Tucker’s quantum theory of mixing (QTM). The small superconducting energy gap of Al enabled us to study mixer performance at around the junction gap frequency, fg =(Δ1+Δ2)/h≊87 GHz, of superconductor-insulator-superconductor (SIS) mixers, and at twice the junction gap frequency for S-I-normal metal (SIN) mixers ( fg =Δ1/h) with available millimeter wave sources. Because of the low transition temperature of Al (Tc ≊1.3 K), a dilution refrigerator was used for providing temperatures below 1 K. The best mixer conversion efficiency was obtained for a low-resistance (∼34 Ω) six-junction array SIS mixer operated at f/fg ≊1 (in this case 73 GHz). The coupled single sideband conversion gain (with no image rejection) was −13.8 dB and the available conversion gain was estimated to −8.4 dB. Complicating nonequilibrium phenomena made it difficult to compare the performance of these relatively high-current-density mixers to the QTM. However, good agreement between calculated and corresponding measured conversion efficiencies and dynamic resistance values was obtained for the low-current-density mixers. Noise due to switching between rf-induced Josephson steps and interference from Josephson mixing could be quenched by a magnetic field. Several high-frequency limits are considered in this paper (such as Josephson switching noise, nonequilibrium phenomena, pair breaking, and energy gap limitations). Our results indicate that submillimeter wave SIS mixer receivers are likely to perform well, at least up to their gap frequencies, i.e., the THz region for large gap superconductors. Our QTM calculations showed that conversion gain larger than unity should be possible up to twice the gap frequency. Above this frequency the conversion loss will increase rapidly.
Quasiparticle mixers have shown strong quantum effects, conversion gain, and noise levels approaching the quantum limit, but only in tunnel junctions with very low sub-gap "leakage" conductance. It has been suggested that SIS' tunnel junctions, made from two different conductors with unequal gaps, will function as high gain mixers since the dynamic conductance below the gap is negative. We report results of the first SIS' mixing and direct detection experiments. At 36 GHz, a conversion efficiency of -4 dB with a noise temperature of 33 K (SSB) has been obtained. A novel gain mechanism for SIS' direct detectors is predicted. A direct detector responsivity of 250 A/W was measured. We compare our results to quantum theory models. In addition, we demonstrate quasiparticle harmonic mixing of a 36 GHz signal with an 18 GHz local oscillator in tin SIS junctions. Harmonic mixers can have important advantages at high microwave frequencies where insufficient local oscillator power is available.
the possibility of using superconductor–insulator–superconductor (SIS) tunnel junctions in a cryogenic multiplexing system for setting an ac current through arrays of transition edge sensors and reading out the received signal, as well as for setting a dc current through arrays of superconducting quantum interferometers is studied. Operation of the SIS frequency converter at relatively low (below 10 GHz) working frequencies is experimentally investigated. Different operation regimes are implemented; the conversion loss in the quasiparticle mode is found to be 8 dB and the output saturation power is–58 dBm. The possibility of up-conversion of several input signal frequencies simultaneously is demonstrated. It is shown that the SIS junction can be used as a current source controlled by an external RF signal.
Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.
A 230-GHz subharmonically pumped waveguide mixer employing superconducting tunnel junctions has been developed. We present, in this paper, an experimental study of harmonic superconductor-insulator-superconductor (SIS) mixing at 230 GHz, focusing mainly on its noise behavior. The mixer has a double-tuned waveguide structure and employs an array of four 1.7-/spl mu/m/sup 2/ Nb-AlOx-Nb SIS junctions in series, with /spl omega/R/sub n/C/sub j//spl sim/3 at 230 GHz. Harmonic quantum mixing occurred over an experimental frequency range of 205-235 GHz (local oscillator: 112.5-117.5 GHz), exhibiting corresponding double sideband noise temperatures of lower than 150 K, with a lowest value of 75 K at /spl sim/230 GHz. The measured mixer noise is believed to be the lowest yet reported for a mixer using subharmonic-pump configuration at this frequency. A phenomenon that we attribute to the third harmonic SIS mixing has also been observed.