Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

An experimental study of harmonic sis mixing at 205-235 ghz

Kecheng Xiao, Hideo Ogawa, Yasuo Fukui

Published Dec 1, 2003• 3 citations
Publisher

Abstract

A 230-GHz subharmonically pumped waveguide mixer employing superconducting tunnel junctions has been developed. We present, in this paper, an experimental study of harmonic superconductor-insulator-superconductor (SIS) mixing at 230 GHz, focusing mainly on its noise behavior. The mixer has a double-tuned waveguide structure and employs an array of four 1.7-/spl mu/m/sup 2/ Nb-AlOx-Nb SIS junctions in series, with /spl omega/R/sub n/C/sub j//spl sim/3 at 230 GHz. Harmonic quantum mixing occurred over an experimental frequency range of 205-235 GHz (local oscillator: 112.5-117.5 GHz), exhibiting corresponding double sideband noise temperatures of lower than 150 K, with a lowest value of 75 K at /spl sim/230 GHz. The measured mixer noise is believed to be the lowest yet reported for a mixer using subharmonic-pump configuration at this frequency. A phenomenon that we attribute to the third harmonic SIS mixing has also been observed.

DOI
10.1109/tasc.2003.820510

Related papers

A 230 GHz low noise subharmonically pumped SIS mixer

K. C. Xiao, Hideo Ogawa, Akira Mizuno +1 more

A 230 GHz Low Noise Subharmonically Pumped (SHP) SIS mixer has been developed and tested at 115 GHz LO. The mixer has a two backshorts waveguide structure and employs an array of four 1.7 /spl mu/m/sup 2/ Nb/AlO/sub x//Nb SIS junctions in series with /spl omega/RnC/spl sim/3 at 230 GHz. Harmonic quantum mixing occurred over the whole experimental frequency range of 208-234 GHz (LO:114-117 GHz), with the corresponding DSB noise temperatures of lower than 150 K and a lowest value of 75 K at /spl sim/230 GHz. The present noise results are believed to be the lowest yet reported for a SHP mixer.

IEEE MTT-S International Microwave Symposium digest•Nov 7, 2002•2 citations

A low noise 410-495 GHz Nb/Al/sub 2/O/sub 3//Nb SIS waveguide mixer

Gert J. de Lange, Cornelia E. Honingh, M. M. T. M. Dierichs +5 more

The noise and gain of a heterodyne waveguide mixer using Nb/Al/sub 2/O/sub 3//Nb superconducting tunnel junctions were measured in the 400-500-GHz frequency range. Three different arrays of two junctions in series are analyzed. The minimum receiver noise temperature is 120 K DSB at 480 GHz, measured with an array having integrated tuning stubs. The authors compare data of the pumped I-V curves with the Werthammer-Tucker theory and demonstrate an excellent agreement at frequencies up to 500 GHz. For an array without integrated tuning stubs. a mixer noise temperature of 90+or-30 K and a DSB mixer gain of -12.5+or-0.6 dB were measured. A comparison of the measured gain versus bias voltage with the quantum theory of mixing shows good qualitative agreement, indicating the applicability of this theory to Nb tunnel junctions up to 500 GHz. The noise temperature of an array with a lower gap voltage is 220 K at 495 GHz. This frequency is 85% of the reduced gap frequency, indicating that Nb superconductor insulator-superconductor (SIS) mixers can be used up at least the gap frequency of 680 GHz.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•13 citations

A 200-285-GHz waveguide SIS mixer with an inhomogeneous distributed junction array

Mahoto Takeda, Takashi Noguchi

In this paper, we present the experimental results of a waveguide superconductor-insulator-superconductor (SIS) mixer with an inhomogeneous distributed junction array. The mixer consists of five Nb-AlO/sub x/-Nb SIS junctions with different dimensions distributed on a superconducting microstrip. The critical current density of the fabricated junctions was 3100 A/cm/sup 2/. Detailed measurements of the receiver noise temperature have been made in the frequency range from 190 to 284 GHz at 4.2 K. A double-sideband (DSB) receiver noise temperature of 5 hw/k was obtained in the frequency range from 202 to 284 GHz and the lowest DSB receiver noise temperature of 46 K was obtained at 210 GHz.

IEEE Transactions on Microwave Theory and Techniques•Nov 1, 2002•2 citations

An SIS Mixer With 2hf/k DSB Noise Temperature at 163 - 211 GHz Band

Bhushan Billade, Alexey Pavolotsky, Victor Y. Belitsky

We present the design and the performance of a fixed-tuned, all niobium (Nb) Superconductor-Insulator-Superconductor (SIS) mixer covering RF frequencies from 163 to 211 GHz with 4-8 GHz IF bandwidth. The mixer uses two Nb/Al-AlOx/Nb junctions of size 3 μm2each with theRnAproduct of 30 Ω·μm2, in a twin junction configuration. An local oscillator (LO) directional coupler made of superconducting lines with slots in the ground plane is integrated on the SIS mixer chip. The isolated port of the LO coupler is terminated using a wide-band resistive load with a sheet resistance of 12 Ω/□. The SIS tuning circuitry is optimized to achieve best power match between the twin junctions and the embedding circuitry. The measurement of the double sideband mixer noise at 171 GHz shows that the receiver noise temperature is approximately 17 K, which is just 2hf/k. The estimated noise contribution from the RF loss and the IF chain at 176 GHz LO frequency is 8 K and 7.5 K respectively, resulting in a SIS mixer noise ofhf/2k. The mixer noise performance across the entire RF band varies between 19 to 25 K. This is to our knowledge the best reported noise temperature at these frequencies till now.

IEEE Transactions on Terahertz Science and Technology•May 2, 2013•20 citations

Observation of subharmonically pumped mixing with gain using SIS junctions

S. E. G. Slusky, R. Trambarulo, Linus A. Fetter

We have observed subharmonically pumped, switched mode mixing in superconductor-insulator-superconductor (SIS) junctions. Experiments were performed at signal frequencies of 14.4 and 16.8 GHz using PbIn-oxide-Pb junctions approximately 1 μm × ½ μm The best single sideband power conversion seen was 2.0 ± 0.5 dB gain. The lowest single sideband mixer temperature measured was 48 ± 47K. This is the first superconducting mixer to combine the advantages of subharmonic pumping with single sideband gain and low noise.

IEEE Transactions on Magnetics•Jan 1, 1981•3 citations

Low noise broadband fixed tuned SIS waveguide mixers at 660 and 800 GHz

Cornelia E. Honingh, Sybille Haas, D. Hottgenroth +2 more

We present measurements and simulations of mixer performance around 660 GHz and around 800 GHz. We use Nb-Al/sub 2/O/sub 3/-Nb tunnel junctions with areas of 0.9 /spl mu/m/sup 2/ and 0.7 /spl mu/m/sup 2/, and RA-products of 14.5 /spl Omega/(/spl mu/m)/sup 2/ and 13 /spl Omega/(/spl mu/m)/sup 2/ for 660 GHz and 800 GHz. Both junctions have an integrated tuning structure made of niobium that consists of a series resonant stub and a quarter lambda transformer. The waveguide mixerblock has no additional adjustable tuning elements. It contains just a waveguide cavity and a substrate channel across it. A horn is carefully adjusted to the cavity and flanged to the block. The measured receiver noise temperatures from 630-690 GHz are below 190 K with a best value of 120 K at 655 GHz. From 780-820 GHz they are below 950 K with a best value of 780 K at 792 GHz. When the operating temperature is reduced from 4.2 K to 2.5 K, a reduction in noise temperature from 830 K to 660 K is observed at 810 GHz. The mixer performance is simulated using the quantum theory of mixing. The simulated performance shows a fairly good agreement with the measured one.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•21 citations
A 230-GHz subharmonically pumped waveguide mixer employing superconducting tunnel junctions has been developed. We present, in this paper, an experimental study of harmonic superconductor-insulator-superconductor (SIS) mixing at 230 GHz, focusing mainly on its noise behavior. The mixer has a double-tuned waveguide structure and employs an array of four 1.7-/spl mu/m/sup 2/ Nb-AlOx-Nb SIS junctions in series, with /spl omega/R/sub n/C/sub j//spl sim/3 at 230 GHz. Harmonic quantum mixing occurred over an experimental frequency range of 205-235 GHz (local oscillator: 112.5-117.5 GHz), exhibiting corresponding double sideband noise temperatures of lower than 150 K, with a lowest value of 75 K at /spl sim/230 GHz. The measured mixer noise is believed to be the lowest yet reported for a mixer using subharmonic-pump configuration at this frequency. A phenomenon that we attribute to the third harmonic SIS mixing has also been observed.
A 230 GHz Low Noise Subharmonically Pumped (SHP) SIS mixer has been developed and tested at 115 GHz LO. The mixer has a two backshorts waveguide structure and employs an array of four 1.7 /spl mu/m/sup 2/ Nb/AlO/sub x//Nb SIS junctions in series with /spl omega/RnC/spl sim/3 at 230 GHz. Harmonic quantum mixing occurred over the whole experimental frequency range of 208-234 GHz (LO:114-117 GHz), with the corresponding DSB noise temperatures of lower than 150 K and a lowest value of 75 K at /spl sim/230 GHz. The present noise results are believed to be the lowest yet reported for a SHP mixer.
The noise and gain of a heterodyne waveguide mixer using Nb/Al/sub 2/O/sub 3//Nb superconducting tunnel junctions were measured in the 400-500-GHz frequency range. Three different arrays of two junctions in series are analyzed. The minimum receiver noise temperature is 120 K DSB at 480 GHz, measured with an array having integrated tuning stubs. The authors compare data of the pumped I-V curves with the Werthammer-Tucker theory and demonstrate an excellent agreement at frequencies up to 500 GHz. For an array without integrated tuning stubs. a mixer noise temperature of 90+or-30 K and a DSB mixer gain of -12.5+or-0.6 dB were measured. A comparison of the measured gain versus bias voltage with the quantum theory of mixing shows good qualitative agreement, indicating the applicability of this theory to Nb tunnel junctions up to 500 GHz. The noise temperature of an array with a lower gap voltage is 220 K at 495 GHz. This frequency is 85% of the reduced gap frequency, indicating that Nb superconductor insulator-superconductor (SIS) mixers can be used up at least the gap frequency of 680 GHz.>
In this paper, we present the experimental results of a waveguide superconductor-insulator-superconductor (SIS) mixer with an inhomogeneous distributed junction array. The mixer consists of five Nb-AlO/sub x/-Nb SIS junctions with different dimensions distributed on a superconducting microstrip. The critical current density of the fabricated junctions was 3100 A/cm/sup 2/. Detailed measurements of the receiver noise temperature have been made in the frequency range from 190 to 284 GHz at 4.2 K. A double-sideband (DSB) receiver noise temperature of 5 hw/k was obtained in the frequency range from 202 to 284 GHz and the lowest DSB receiver noise temperature of 46 K was obtained at 210 GHz.
We present the design and the performance of a fixed-tuned, all niobium (Nb) Superconductor-Insulator-Superconductor (SIS) mixer covering RF frequencies from 163 to 211 GHz with 4-8 GHz IF bandwidth. The mixer uses two Nb/Al-AlOx/Nb junctions of size 3 μm2each with theRnAproduct of 30 Ω·μm2, in a twin junction configuration. An local oscillator (LO) directional coupler made of superconducting lines with slots in the ground plane is integrated on the SIS mixer chip. The isolated port of the LO coupler is terminated using a wide-band resistive load with a sheet resistance of 12 Ω/□. The SIS tuning circuitry is optimized to achieve best power match between the twin junctions and the embedding circuitry. The measurement of the double sideband mixer noise at 171 GHz shows that the receiver noise temperature is approximately 17 K, which is just 2hf/k. The estimated noise contribution from the RF loss and the IF chain at 176 GHz LO frequency is 8 K and 7.5 K respectively, resulting in a SIS mixer noise ofhf/2k. The mixer noise performance across the entire RF band varies between 19 to 25 K. This is to our knowledge the best reported noise temperature at these frequencies till now.
We have observed subharmonically pumped, switched mode mixing in superconductor-insulator-superconductor (SIS) junctions. Experiments were performed at signal frequencies of 14.4 and 16.8 GHz using PbIn-oxide-Pb junctions approximately 1 μm × ½ μm The best single sideband power conversion seen was 2.0 ± 0.5 dB gain. The lowest single sideband mixer temperature measured was 48 ± 47K. This is the first superconducting mixer to combine the advantages of subharmonic pumping with single sideband gain and low noise.
We present measurements and simulations of mixer performance around 660 GHz and around 800 GHz. We use Nb-Al/sub 2/O/sub 3/-Nb tunnel junctions with areas of 0.9 /spl mu/m/sup 2/ and 0.7 /spl mu/m/sup 2/, and RA-products of 14.5 /spl Omega/(/spl mu/m)/sup 2/ and 13 /spl Omega/(/spl mu/m)/sup 2/ for 660 GHz and 800 GHz. Both junctions have an integrated tuning structure made of niobium that consists of a series resonant stub and a quarter lambda transformer. The waveguide mixerblock has no additional adjustable tuning elements. It contains just a waveguide cavity and a substrate channel across it. A horn is carefully adjusted to the cavity and flanged to the block. The measured receiver noise temperatures from 630-690 GHz are below 190 K with a best value of 120 K at 655 GHz. From 780-820 GHz they are below 950 K with a best value of 780 K at 792 GHz. When the operating temperature is reduced from 4.2 K to 2.5 K, a reduction in noise temperature from 830 K to 660 K is observed at 810 GHz. The mixer performance is simulated using the quantum theory of mixing. The simulated performance shows a fairly good agreement with the measured one.