Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE

Coherent detection of weak signals with superconducting nanowire single photon detector at the telecommunication wavelength

Michael Shcherbatenko, Y. Lobanov, Alexander V. Semenov, Vadim V. Kovalyuk, Alexander A. Korneev, Roman V. Ozhegov, N. Kaurova, B. Voronov, Gregory N Gol'tsman

Published May 15, 2017• 0 citations
Publisher

Abstract

Achievement of the ultimate sensitivity along with a high spectral resolution is one of the frequently addressed problems, as the complication of the applied and fundamental scientific tasks being explored is growing up gradually. In our work, we have investigated performance of a superconducting nanowire photon-counting detector operating in the coherent mode for detection of weak signals at the telecommunication wavelength. Quantum-noise limited sensitivity of the detector was ensured by the nature of the photon-counting detection and restricted by the quantum efficiency of the detector only. Spectral resolution given by the heterodyne technique and was defined by the linewidth and stability of the Local Oscillator (LO). Response bandwidth was found to coincide with the detector’s pulse width, which, in turn, could be controlled by the nanowire length. In addition, the system noise bandwidth was shown to be governed by the electronics/lab equipment, and the detector noise bandwidth is predicted to depend on its jitter. As have been demonstrated, a very small amount of the LO power (of the order of a few picowatts down to hundreds of femtowatts) was required for sufficient detection of the test signal, and eventual optimization could lead to further reduction of the LO power required, which would perfectly suit for the foreseen development of receiver matrices and the need for detection of ultra-low signals at a level of less-than-one-photon per second.

DOI
10.1117/12.2267724

Related papers

Superconducting Nanowire Single Photon Detector for Coherent Detection of Weak Signals

Yury Lobanov, Michael Shcherbatenko, Alexander V. Semenov +9 more

Traditional photon detectors are operated in the direct detection mode, counting incident photons with a known quantum efficiency. Here, we have investigated a superconducting nanowire single photon detector (SNSPD) operated as a photon counting mixer at telecommunication wavelength around 1.5 μm. This regime of operation combines excellent sensitivity of a photon counting detector with excellent spectral resolution given by the heterodyne technique. Advantageously, we have found that low local oscillator (LO) power of the order of hundreds of femtowatts to a few picowatts is sufficient for clear observation of the incident test signal with the sensitivity approaching the quantum limit. With further optimization, the required LO power could be significantly reduced, which is promising for many practical applications, such as the development of receiver matrices or recording ultralow signals at a level of less-than-one-photon per second. In addition to a traditional NbN-based SNSPD operated with normal incidence coupling, we also use detectors with a travelling wave geometry, where a NbN nanowire is placed on the top of a Si3N4nanophotonic waveguide. This approach is fully scalable and a large number of devices could be integrated on a single chip.

IEEE Transactions on Applied Superconductivity•Dec 26, 2016•6 citations

On-chip coherent detection with quantum limited sensitivity

Vadim V. Kovalyuk, Simone Ferrari, Oliver Kahl +9 more

Abstract While single photon detectors provide superior intensity sensitivity, spectral resolution is usually lost after the detection event. Yet for applications in low signal infrared spectroscopy recovering information about the photon’s frequency contributions is essential. Here we use highly efficient waveguide integrated superconducting single-photon detectors for on-chip coherent detection. In a single nanophotonic device, we demonstrate both single-photon counting with up to 86% on-chip detection efficiency, as well as heterodyne coherent detection with spectral resolution f/∆f exceeding 1011. By mixing a local oscillator with the single photon signal field, we observe frequency modulation at the intermediate frequency with ultra-low local oscillator power in the femto-Watt range. By optimizing the nanowire geometry and the working parameters of the detection scheme, we reach quantum-limited sensitivity. Our approach enables to realize matrix integrated heterodyne nanophotonic devices in the C-band wavelength range, for classical and quantum optics applications where single-photon counting as well as high spectral resolution are required simultaneously.

Scientific Reports•Jun 30, 2017•19 citations

Towards linear optical detection with single photon sensitivity at telecom wavelengths

Saeedeh Jahanmirinejad, Andrea Fiore

Standard linear optical detectors have a maximum sensitivity in the few hundreds of photons range, limited by amplifier noise. On the other hand, single photon detectors, which are the most sensitive detectors, are strongly nonlinear: One or more photons result in the same output signal. Photon number resolving (PNR) detectors, which have the ability to discriminate the number of photons in a weak optical pulse, are of great importance in the field of quantum information processing and quantum cryptography. Moreover, a PNR detector with large dynamic range can cover the gap between these two detection modes. Such detectors are greatly desirable not only in quantum information science and technology, but also in any application dealing with low light levels. In this work, we propose a novel approach to photon number resolving detectors based on spatial multiplexing of nanowire superconducting single-photon detectors. In the proposed approach, N superconducting nanowires, each connected in parallel to an integrated resistor, are connected in series. Photon absorption in a nanowire switches its bias current to the parallel resistor, forming a voltage pulse across it. The sum of these voltages, proportional to the number of absorbed photons, is measured at the output. The use of a cryogenic preamplifier with high input impedance for the read-out increases the linearity, the signal to noise ratio, and the speed. With this combination, we expect to be able to count up to few tens of photons with high fidelity, excellent timing resolution, and very high sensitivity in the telecommunication wavelength range.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 21, 2012•2 citations

A superconducting nanowire single-photon detector system for single-photon source characterization

Catherine R. M. Fitzpatrick, Chandra M. Natarajan, Ryan E. Warburton +8 more

Single-photon sources and detectors are key enabling technologies for photonics in quantum information science and technology (QIST). QIST applications place high-level demands on the performance of sources and detectors; it is therefore essential that their properties can be characterized accurately. Superconducting nanowire single-photon detectors (SNSPDs) have spectral sensitivity from visible to beyond 2 μm in wavelength, picosecond timing resolution (Jitter <100 ps FWHM) and the capacity to operate ungated with low dark counts (<1 kHz). This facilitates data acquisition at high rates with an excellent signal-to-noise ratio. We report on the construction and characterization of a two-channel SNSPD system. The detectors are mounted in a closed-cycle refrigerator, which eliminates reliance on liquid cryogens. Our specification was to deliver a system with 1% efficiency in both channels at a wavelength of 1310 nm with 1 kHz dark count rate. A full width at half maximum timing jitter of less than 90 ps is achieved in both channels. The system will be used to detect individual photons generated by quantum-optical sources at telecom wavelengths. Examples include single-photon sources based on quantum dots (emitting at 1310 nm). The SNSPD system's spectral sensitivity and timing resolution make it suited to characterization of such sources, and to wider QIST applications.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 20, 2010•0 citations

Heterodyne spectroscopy with superconducting single-photon detector

Yu. V. Lobanov, Michael Shcherbatenko, Alexander V. Semenov +3 more

We demonstrate successful operation of a Superconducting Single Photon Detector (SSPD) as the core element in a heterodyne receiver. Irradiating the SSPD by both a local oscillator power and signal power simultaneously, we observed beat signal at the intermediate frequency of a few MHz. Gain bandwidth was found to coincide with the detector single pulse width, where the latter depends on the detector kinetic inductance, determined by the superconducting nanowire length.

EPJ Web of Conferences•Dec 13, 2016•0 citations

Waveguide integrated low noise NbTiN nanowire single-photon detectors with milli-Hz dark count rate

Carsten Schuck, Wolfram H. P. Pernice, Hong X. Tang

Superconducting nanowire single-photon detectors are an ideal match for integrated quantum photonic circuits due to their high detection efficiency for telecom wavelength photons. Quantum optical technology also requires single-photon detection with low dark count rate and high timing accuracy. Here we present very low noise superconducting nanowire single-photon detectors based on NbTiN thin films patterned directly on top of Si3N4 waveguides. We systematically investigate a large variety of detector designs and characterize their detection noise performance. Milli-Hz dark count rates are demonstrated over the entire operating range of the nanowire detectors which also feature low timing jitter. The ultra-low dark count rate, in combination with the high detection efficiency inherent to our travelling wave detector geometry, gives rise to a measured noise equivalent power at the 10(-20) W/Hz(1/2) level.

arXiv:1306.0164•Scientific Reports•May 29, 2013•148 citations
Achievement of the ultimate sensitivity along with a high spectral resolution is one of the frequently addressed problems, as the complication of the applied and fundamental scientific tasks being explored is growing up gradually. In our work, we have investigated performance of a superconducting nanowire photon-counting detector operating in the coherent mode for detection of weak signals at the telecommunication wavelength. Quantum-noise limited sensitivity of the detector was ensured by the nature of the photon-counting detection and restricted by the quantum efficiency of the detector only. Spectral resolution given by the heterodyne technique and was defined by the linewidth and stability of the Local Oscillator (LO). Response bandwidth was found to coincide with the detector’s pulse width, which, in turn, could be controlled by the nanowire length. In addition, the system noise bandwidth was shown to be governed by the electronics/lab equipment, and the detector noise bandwidth is predicted to depend on its jitter. As have been demonstrated, a very small amount of the LO power (of the order of a few picowatts down to hundreds of femtowatts) was required for sufficient detection of the test signal, and eventual optimization could lead to further reduction of the LO power required, which would perfectly suit for the foreseen development of receiver matrices and the need for detection of ultra-low signals at a level of less-than-one-photon per second.
Traditional photon detectors are operated in the direct detection mode, counting incident photons with a known quantum efficiency. Here, we have investigated a superconducting nanowire single photon detector (SNSPD) operated as a photon counting mixer at telecommunication wavelength around 1.5 μm. This regime of operation combines excellent sensitivity of a photon counting detector with excellent spectral resolution given by the heterodyne technique. Advantageously, we have found that low local oscillator (LO) power of the order of hundreds of femtowatts to a few picowatts is sufficient for clear observation of the incident test signal with the sensitivity approaching the quantum limit. With further optimization, the required LO power could be significantly reduced, which is promising for many practical applications, such as the development of receiver matrices or recording ultralow signals at a level of less-than-one-photon per second. In addition to a traditional NbN-based SNSPD operated with normal incidence coupling, we also use detectors with a travelling wave geometry, where a NbN nanowire is placed on the top of a Si3N4nanophotonic waveguide. This approach is fully scalable and a large number of devices could be integrated on a single chip.
Abstract While single photon detectors provide superior intensity sensitivity, spectral resolution is usually lost after the detection event. Yet for applications in low signal infrared spectroscopy recovering information about the photon’s frequency contributions is essential. Here we use highly efficient waveguide integrated superconducting single-photon detectors for on-chip coherent detection. In a single nanophotonic device, we demonstrate both single-photon counting with up to 86% on-chip detection efficiency, as well as heterodyne coherent detection with spectral resolution f/∆f exceeding 1011. By mixing a local oscillator with the single photon signal field, we observe frequency modulation at the intermediate frequency with ultra-low local oscillator power in the femto-Watt range. By optimizing the nanowire geometry and the working parameters of the detection scheme, we reach quantum-limited sensitivity. Our approach enables to realize matrix integrated heterodyne nanophotonic devices in the C-band wavelength range, for classical and quantum optics applications where single-photon counting as well as high spectral resolution are required simultaneously.
Standard linear optical detectors have a maximum sensitivity in the few hundreds of photons range, limited by amplifier noise. On the other hand, single photon detectors, which are the most sensitive detectors, are strongly nonlinear: One or more photons result in the same output signal. Photon number resolving (PNR) detectors, which have the ability to discriminate the number of photons in a weak optical pulse, are of great importance in the field of quantum information processing and quantum cryptography. Moreover, a PNR detector with large dynamic range can cover the gap between these two detection modes. Such detectors are greatly desirable not only in quantum information science and technology, but also in any application dealing with low light levels. In this work, we propose a novel approach to photon number resolving detectors based on spatial multiplexing of nanowire superconducting single-photon detectors. In the proposed approach, N superconducting nanowires, each connected in parallel to an integrated resistor, are connected in series. Photon absorption in a nanowire switches its bias current to the parallel resistor, forming a voltage pulse across it. The sum of these voltages, proportional to the number of absorbed photons, is measured at the output. The use of a cryogenic preamplifier with high input impedance for the read-out increases the linearity, the signal to noise ratio, and the speed. With this combination, we expect to be able to count up to few tens of photons with high fidelity, excellent timing resolution, and very high sensitivity in the telecommunication wavelength range.
Single-photon sources and detectors are key enabling technologies for photonics in quantum information science and technology (QIST). QIST applications place high-level demands on the performance of sources and detectors; it is therefore essential that their properties can be characterized accurately. Superconducting nanowire single-photon detectors (SNSPDs) have spectral sensitivity from visible to beyond 2 μm in wavelength, picosecond timing resolution (Jitter <100 ps FWHM) and the capacity to operate ungated with low dark counts (<1 kHz). This facilitates data acquisition at high rates with an excellent signal-to-noise ratio. We report on the construction and characterization of a two-channel SNSPD system. The detectors are mounted in a closed-cycle refrigerator, which eliminates reliance on liquid cryogens. Our specification was to deliver a system with 1% efficiency in both channels at a wavelength of 1310 nm with 1 kHz dark count rate. A full width at half maximum timing jitter of less than 90 ps is achieved in both channels. The system will be used to detect individual photons generated by quantum-optical sources at telecom wavelengths. Examples include single-photon sources based on quantum dots (emitting at 1310 nm). The SNSPD system's spectral sensitivity and timing resolution make it suited to characterization of such sources, and to wider QIST applications.
Superconducting nanowire single-photon detectors are an ideal match for integrated quantum photonic circuits due to their high detection efficiency for telecom wavelength photons. Quantum optical technology also requires single-photon detection with low dark count rate and high timing accuracy. Here we present very low noise superconducting nanowire single-photon detectors based on NbTiN thin films patterned directly on top of Si3N4 waveguides. We systematically investigate a large variety of detector designs and characterize their detection noise performance. Milli-Hz dark count rates are demonstrated over the entire operating range of the nanowire detectors which also feature low timing jitter. The ultra-low dark count rate, in combination with the high detection efficiency inherent to our travelling wave detector geometry, gives rise to a measured noise equivalent power at the 10(-20) W/Hz(1/2) level.