Quantum technology has made great strides in the last two decades with trapped ions demonstrating all the necessary building blocks for a quantum computer. While these proof of principle experiments have been demonstrated, it still remains a challenging task to scale these experiments down to smaller systems. In this thesis I describe the development of technology towards scalable cryogenic ion trapping and quantum hybrid systems. I first discuss the fundamentals of ion trapping along with the demonstration of ion trapping on a novel surface electrode ion trap with a ring shaped architecture. I then present the development of a cryogenic vacuum system for ion trapping at ~4 K, which utilizes a closed cycle Gifford McMahon cryocooler with a helium gas buffered ultra-low vibration interface to mechanically decouple a ultra-high vacuum system. Ancillary technologies are also presented, including a novel in-vacuum superconducting rf resonator, low power dissipation ceramic based atomic source oven and an adaptable in-vacuum permanent magnet system for long-wavelength based quantum logic. The design and fabrication of microfabricated surface ion traps toward quantum hybrid technologies are then presented. A superconducting ion trap with an integrated high quality factor microwave cavity and vertical ion shuttling capabilities is described. The experimental demonstration of the cavity is also presented with quality factors of Q6~6000 and Q~15000 for superconducting niobium nitride and gold based cavities respectively, which are the highest demonstrated for microwave cavities integrated within ion trapping electrode architectures. An ion trap with a multipole electrode geometry is then presented, which is capable of trapping a large number of ions simultaneously. The homogeneity of five individual linear trapping regions are optimized and the design for the principle axis rotation of each linear region is presented. An overview of microfabrication techniques used for fabricating surface electrode ion traps is then presented. This includes the detailed microfabrication procedure for ion traps designed within this thesis. A scheme for the integration of ion trapping and superconducting qubit systems as a step towards the realization of a quantum hybrid system is then presented. This scheme addresses two key diffculties in realizing such a system; a combined microfabricated ion trap and superconducting qubit architecture, and the experimental infrastructure to facilitate both technologies. Solutions that can be immediately implemented using current technology are presented. Finally, as a step towards scalability and hybrid quantum systems, the interaction between a single ion and a microwaves field produced from an on chip microwave cavity is explored. The interaction is described for the high-Q microwave cavity designed in this thesis and a 171Yb+ion. A description of the observable transmission from the cavity is described and it is shown that the presence of a single ion can indeed be observed in the emission spectrum of high-Q microwave cavity even in the weak coupling regime.
Quantum technology has made great strides in the last two decades with trapped ions demonstrating all the necessary building blocks for a quantum computer. While these proof of principle experiments have been demonstrated, it still remains a challenging task to scale these experiments down to smaller systems. In this thesis I describe the development of technology towards scalable cryogenic ion trapping and quantum hybrid systems. I first discuss the fundamentals of ion trapping along with the demonstration of ion trapping on a novel surface electrode ion trap with a ring shaped architecture. I then present the development of a cryogenic vacuum system for ion trapping at 4 K, which utilizes a closed cycle Gifford McMahon cryocooler with a helium gas buffered ultra-low vibration interface to mechanically decouple a ultra-high vacuum system. Ancillary technologies are also presented, including a novel in-vacuum superconducting rf resonator, low power dissipation ceramic based atomic source oven and an adaptable in-vacuum permanent magnet system for long-wavelength based quantum logic. The design and fabrication of microfabricated surface ion traps toward quantum hybrid technologies are then presented. A superconducting ion trap with an integrated high quality factor microwave cavity and vertical ion shuttling capabilities is described. The experimental demonstration of the cavity is also presented with quality factors of Q66000 and Q~15000 for superconducting niobium nitride and gold based cavities respectively, which are the highest demonstrated for microwave cavities integrated within ion trapping electrode architectures. An ion trap with a multipole electrode geometry is then presented, which is capable of trapping a large number of ions simultaneously. The homogeneity of five individual linear trapping regions are optimized and the design for the principle axis rotation of each linear region is presented. An overview of microfabrication techniques used for fabricating surface electrode ion traps is then presented. This includes the detailed microfabrication procedure for ion traps designed within this thesis. A scheme for the integration of ion trapping and superconducting qubit systems as a step towards the realization of a quantum hybrid system is then presented. This scheme addresses two key diffculties in realizing such a system; a combined microfabricated ion trap and superconducting qubit architecture, and the experimental infrastructure to facilitate both technologies. Solutions that can be immediately implemented using current technology are presented. Finally, as a step towards scalability and hybrid quantum systems, the interaction between a single ion and a microwaves field produced from an on chip microwave cavity is explored. The interaction is described for the high-Q microwave cavity designed in this thesis and a 171Yb+ion. A description of the observable transmission from the cavity is described and it is shown that the presence of a single ion can indeed be observed in the emission spectrum of high-Q microwave cavity even in the weak coupling regime.
Microfabricated ion traps are an important tool in the development of scalable quantum systems. Tremendous advancements towards an ion quantum computer were made in the past decade and most requirements for a quantum computer have been fulfilled in individual experiments. Incorporating all essential capabilities in a fully scalable system will require the further advancement of established quantum information technologies and development of new trap fabrication techniques. In my thesis I will discuss the theoretical background and experimental setup required for the operation of ion traps. Measurement of the important ion trap heating rate was performed in the setup and I will discuss the results in more detail. I will give a review of microfabrication processes used for the fabrication of traps, outlining advantages, disadvantages and issues inherent to the processes. Following the review I will present my work on a concept for a scalable ion trap quantum system based on microwave quantum gates and shuttling through X-junctions. Many of the required building blocks, including ion trap structures with current-carrying wires intended to create strong magnetic field gradients for microwave gates were investigated further. A novel fabrication process was developed to combine current-carrying wires with advanced multilayered ion trap structures. Several trap designs intended for proof of principle experiments of high fidelity microwave gates, advanced detection techniques and shuttling between electrically disconnected ion traps will be presented. Also the electrode geometry of an optimized X-junction design with strongly suppressed rf barrier height will be presented. Further, I developed several modifications for the experimental setup to extend the existing capabilities. A plasma source capable of performing in-situ cleans of the trap electrode surfaces, which has been demonstrated to dramatically reduce the heating rate in ion traps, was incorporated. I will also present a vacuum system modification designed to cool ion traps with current-carrying wires and transport the generated heat out of the vacuum system. In addition a novel low-noise, high-speed, multichannel voltage control system was developed by me. The device can be used in future experiments to precisely shuttle ions from one trapping zone to another and also to shuttle ions through ion trap junctions. Lastly I will outline the process optimization and microfabrication of my ion trap designs. A novel fabrication process which makes use of the extremely high thermal conductivity of diamond substrates and combines it with thick copper tracks embedded in the substrate was developed. Large currents will be passed through the wires creating a strong and controllable magnetic field gradient. Ion trap designs with isolated electrodes connected via buried wires can be placed on top of the current-carrying wires, allowing the most advanced electrode designs to be fabricated with current-carrying wires.
We present a design for the experimental integration of ion trapping and superconducting qubit systems as a step towards the realization of a quantum hybrid system. The scheme addresses two key difficulties in realizing such a system; a combined microfabricated ion trap and superconducting qubit architecture, and the experimental infrastructure to facilitate both technologies. Developing upon work by Kielpinski et al. [1] we describe the design, simulation and fabrication process for a microfabricated ion trap capable of coupling an ion to a superconducting microwave LC circuit with a coupling strength in the tens of kHz. We also describe existing difficulties in combining the experimental infrastructure of an ion trapping setup into a dilution fridge with superconducting qubits and present solutions that can be immediately implemented using current technology.
We present a design for the experimental integration of ion trapping and superconducting qubit systems as a step towards the realization of a quantum hybrid system. The scheme addresses two key difficulties in realizing such a system: a combined microfabricated ion trap and superconducting qubit architecture, and the experimental infrastructure to facilitate both technologies. Developing upon work by Kielpinski et al. (Phys Rev Lett 108(13):130504, 2012. doi: 10.1103/PhysRevLett.108.130504 ), we describe the design, simulation and fabrication process for a microfabricated ion trap capable of coupling an ion to a superconducting microwave LC circuit with a coupling strength in the tens of kHz. We also describe existing difficulties in combining the experimental infrastructure of an ion trapping set-up into a dilution refrigerator with superconducting qubits and present solutions that can be immediately implemented using current technology.
Trapped ions within Paul traps have shown to be a promising architecture in the realisation of a quantum information processor together with the ability of providing quantum simulations. Linear Paul traps have demonstrated long coherence times with ions being well isolated from the environment, single and multi-qubit gates and the high fidelity detection of states. The scalability to large number of qubits, incorporating all the previous achievements requires an array of linear ion traps. Microfabrication techniques allow for fabrication and micron level accuracy of the trap electrode dimensions through photolithography techniques. The first part of this thesis presents the experiential setup and trapping of Yb+ ions needed to test large ion trap arrays. This include vacuum systems that can host advanced symmetric and asymmetric ion traps with up to 90 static voltage control electrodes. Demonstration of a single trapped Yb+ ion within a two-layer macroscopic ion trap is presented. with an ion-electrode distance of 310(10) µm. The anomalous heating rate and spectral noise density of the trap was measured, a main form of decoherence within ion traps. The second half of this thesis presents the design and fabrication of multi-layer asymmetric ion traps. This allows for isolated electrodes that cannot be accessed via surface pathways, allowing for higher density of electrodes as well as creating novel trap designs that allow for the potential of quantum simulations to be demonstrated. These include two-dimensional lattices and ring trap designs in which the isolated electrodes provide more control in the ion position. For the microfabrication of these traps I present a novel high-aspect ratio electroplated electrode design that provides shielding of the dielectric layer. This provides a means to mitigate stray electric field due to charge build up on the dielectric surfaces. Electrical testing of the trap structures was performed to test bulk breakdown and surface flashover of the ion trap architectures. Results showed sufficient isolation between electrodes for both radio frequency and static breakdown. Surface flashover voltage measurements over the dielectric layer showed an improvement of more than double over previous results using a new fabrication technique. This will allow for more powerful ion trap chips needed for the next generation of microfabricated ion trap arrays for scalable quantum technologies.
While quantum information processing offers a tantalizing possibility of a significant speedup in execution of certain algorithms, as well as enabling previously unmanageable simulations of large quantum systems, it remains extremely difficult to realize experimentally. Recently, fundamental building blocks of a quantum computer, including one and two qubit gates, teleportation and error correction, were demonstrated using trapped atomic ions. Scaling to a larger number of qubits requires miniaturization of the ion traps, currently limited by the sharply increasing motional state decoherence at sub-100 μm ion-electrode distances. This thesis explores the source and suppression of this decoherence at cryogenic temperatures, and demonstrates fundamental logic gates in a surface electrode ion trap.
Construction of the apparatus requires the development of a number of experimental techniques. Design, numerical simulation and implementation of a surface electrode ion trap is presented. Cryogenic cooling of the trap to near 4 K is accomplished by contact with a bath cryostat. Ions are loaded by ablation or photoionization, both of which are characterized in terms of generated stray fields and heat load.
The bulk of new experimental results deals with measurements of electric field noise at the ion's position. Upon cooling to 6 K, the measured rates are suppressed by up to 7 orders of magnitude, more than two orders of magnitude below previously published data for similarly sized traps operated at room temperature. The observed noise depends strongly on fabrication process, which suggests further improvements are possible. The measured dependence of the electric field noise on temperature is inconsistent with published models, and can be explained using a continuous spectrum of activated fluctuators.
The fabricated surface electrode traps are used to demonstrate coherent operations and the classical control required for trapped ion quantum computation. The necessary spectral properties of coherent light sources are achieved with a novel design using optical feedback to a triangular, medium finesse, cavity, followed by electronic feedback to an ultra-high finesse reference cavity. Single and two qubit operations on a single ion are demonstrated with classical fidelity in excess of 95%. Magnetic field gradient coils built into the trap allow for individual addressing of ions, a prerequisite to scaling to multiple qubits. (Copies available exclusively from MIT Libraries, Rm. 14-0551, Cambridge, MA 02139-4307. Ph. 617-253-5668; Fax 617-253-1690.)
There has been a great deal of effort and progress made towards building a fully scalable quantum computer but there are still significant engineering challenges to overcome. Trapped ions currently represent the best fundamental technology towards achieving this goal and so they form the basis for the work in this thesis. In this thesis I describe the work towards creating a closed cycle cryogenic vacuum system driven by a Gifford McMahon cryogenic cooler. I will show the equipment required to trap a Ytterbium 174/171 ion on a cryogenic surface ion trap. The primary goal is to create a fast turn-around system for ion trap research. Room temperature systems suffer from long baking times and as such ion traps are rarely changed, this means that there is little room for testing and comparing of trap designs and predicting optimum trapping parameters as each trap is usually not changed unless there is a fault. In the cryogenic system, every effort is made to make the system generic enough to allow for any trap design to be tested and to be replaced within 24 hours. To create reliable trapping parameters we require a toolkit that can numerically simulate the required RF and DC voltages used to trap the ions above the surface of the ion trap. There are many numerical methods that can be used (FEM, FVM, BEM, FTDI, etc) and in this thesis I describe multiple methods and what their relative benefits are. Since we want to create a full toolkit to allow for chip design and optimisation, most commercial programs suffer from inadequate API interfaces or they dictate which programming languages you can interface with. This would limit our abilities to develop and optimise trapping parameters, especially in a cryogenic system where the goal is rapid deployment. To this end I created a new toolkit based on the Scuff BEM solver engine that allows us to go from AutoCAD layout to field solver and gives us accurate field potentials that match micromotion compensated voltages to within 1%. I describe a novel cryogenic resonator built out of superconducting wire based on an auto-transformer topology, I compare its strengths and weaknesses compared to other technologies already in use for trapped ion research. I also describe a novel DSUB design with integrated modular filtering which allows for 50 connections per DSUB. This DSUB is used to connect two sets of 50 wires to a PCB for wirebonding to the surface trap. This allows me to save space within the 4k shield where other PCB designs would not fit. Also it is modular in design which allows for different cutoff frequencies to be swapped out as desired. I also describe different chip mounting technologies including epoxy based, physical clamping and indium foil based. After extensive testing the indium foil diebonded approach is deemed as being the most reliable and fastest non-destructive method. I also describe a novel cryogenic coil design for generating 12T m-1 field gradients for microwave based ion gates with Ytterbium 171. I then describe the creation of a combined RF and microwave antenna for delivering coherent RF and 12.6GHz microwave radiation inside the cryogenic environment. This design is much smaller than typical waveguide typologies used. I finish by showing the first trapped ions in a cryogenic surface ion trap in the UK and heating rate tests performed on two different linear surface traps. The first trap was a sapphire based, 150µm ion height linear trap with a measured heating rate of Se(1MHz) = 5.93(10) * 10-14(V /m)2. The second ion trap is a 50k Silicon based, 100µm ion height linear trap with a measured heating rate of Se(1MHz) = 2.45(10)*10-13(V /m)2