Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Broadband Near-Infrared Superconducting Nanowire Single-Photon Detector with Efficiency over 50%

Yong Wang, Hao Li, Lixing You, Chaolin Lv, Jia Huang, Weijun Zhang, Lu Zhang, Xiaoyu Liu, Zhen Wang, Xiaoming Xie

Published Jan 1, 2016• 10 citations
Publisher

Abstract

We report a broadband superconducting nanowire single-photon detector for the near-infrared waveband. The optical absorptance in this band is enhanced by utilizing a reflective aluminum mirror and a SiO2layer as an optical cavity. A broadband system detection efficiency (SDE) over 50% from 950 to 1600 nm with a low dark count rate of 10 Hz is realized by coupling a HI 1060 FLEX single-mode fiber. The SDEs reaches 78.3%, 70.9%, and 57.7% at the wavelengths of 1064, 1310, and 1550 nm, respectively. A system timing resolution (jitter) of 83 ps at 1550 nm is obtained. The detector may be useful for broadband applications such as earth observation, environment monitoring, and biomedicine.

DOI
10.1109/tasc.2016.2642903

Related papers

50 µm diameter superconducting nanowire single-photon detector with sub-17 ps timing jitter and high efficiency for visible wavelengths (Conference Presentation)

Jin Chang, Iman Esmaeil Zadeh

Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.

Quantum Optics and Photon Counting•May 13, 2019•0 citations

Superconducting nanowire single-photon detectors at a wavelength of 940 nm

W. J. Zhang, Hao Li, Lixing You +9 more

We develop single-photon detectors comprising single-mode fiber-coupled superconducting nanowires, with high system detection efficiencies at a wavelength of 940 nm. The detector comprises a 6.5-nm-thick, 110-nm-wide NbN nanowire meander fabricated onto a Si substrate with a distributed Bragg reflector for enhancing the optical absorptance. We demonstrate that, via the design of a low filling factor (1/3) and active area (Φ = 10 μm), the system reaches a detection efficiency of ∼60% with a dark count rate of 10 Hz, a recovery time <12 ns, and a timing jitter of ∼50 ps.

arXiv:1506.07921•AIP Advances•Jun 1, 2015•7 citations

Multimode fiber-coupled superconducting nanowire single-photon detector with 70% system efficiency at visible wavelength

Dengkuan Liu, Shigehito Miki, Taro Yamashita +3 more

We report the development of the multimode fiber-coupled superconducting nanowire single-photon detector with high system detection efficiency at visible wavelength. The detector consists of a 10.5-nm-thick and 150-nm-wide NbN nanowire meander fabricated on a Si substrate with a multilayer dielectric mirror and a quarter wavelength cavity for obtaining high optical absorptance. The meander area was 35 µm in diameter and coupled with the GRIN-lensed multimode optical fiber with a core diameter of 50 µm. The system reached detection efficiency of 70% with dark count rate of 100 Hz at the wavelength of 635 nm, 3 dB roll-off response counting rate of 8.5 Mcps, and timing jitter of 76 ps.

Optics Express•Aug 25, 2014•37 citations

Ultra-broadband microfiber-coupled superconducting single-photon detector

Xintong Hou, Ni Yao, Lixing You +9 more

Broadband photon detectors are a key enabling technology for various applications such as spectrometers, light detection and ranging. In this work, we report on an ultra-broadband single-photon detector based on a microfiber (MF)-coupled superconducting nanowires structure operating in the spectral range from visible to near-infrared light. The MF-coupled superconducting nanowire single-photon detector (SNSPD) is formed by placing an MF on top of superconducting niobium nitride (NbN) nanowires, allowing ultra-broadband photon detection due to their nearly lossless transmission/absorption and nearly unity internal efficiency for ultra-broad waveband. The simulation results indicate that with optimal device structure, the optical absorption with efficiency > 90% can be realized over a wavelength range of 350 nm to 2150 nm. The fabricated MF-coupled SNSPD shows unparalleled broadband system detection efficiencies (SDEs) of more than 50% from 630 nm to 1500 nm. The SDEs reach 66% at 785 nm and 45% at 1550 nm. These results pave the way for ultra-broadband weak light detection with quantum-limit sensitivity.

Optics Express•Aug 22, 2019•8 citations

Performances of NbTiN superconducting nanowire single photon detector

Shigehito Miki, Taro Yamashita, Hirotaka Terai +1 more

We present high performance fiber-coupled niobium titanium nitride superconducting nanowire single photon detectors fabricated on thermally oxidized silicon substrates. By applying a double sided cavity structure, simulated absorptance in the nanowire meander reached 97% at 1550 nm wavelength. The fabricated device showed a system detection efficiency (DE) of 74% at 1550 nm, dark count rate of 100 c/s, and a full width at half maximum timing jitter of 68 ps under a bias current of 18.0 μA with a practical Gifford-McMahon cryocooler system.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2013•1 citation

Next generation superconducting nanowire single-photon detectors

Kleanthis Erotokritou

Single photon detection advanced rapidly in the last decade. The superconducting nanowire single-photon detector (SNSPD) is an emerging technology, which offers low dark count rates, broadband sensitivity from visible to mid-infrared wavelengths and very high quantum efficiency. All these features are appealing for future emerging applications in remote gas sensing, quantum key distribution and quantum information processing. By enclosing the detector in an optical cavity, tuned to the operating wavelength, the total system detection of the SNSPD is improved. Based on the cavity design, the detector absorption is boosted at the desired experimental wavelength. Devices have been fabricated and tested, in this thesis, with enhanced detection efficiency at near-infrared, infrared and mid-infrared wavelengths. NbTiN detectors fabricated on Ta2O5 / SiO2 distributed Bragg reflectors (DBR) for front-side coupling exhibit a system detection efficiency of ≈ 90% at λ = 940 nm for the best device measured. SNSPDs were also fabricated in NbTiN on metallic mirrors for back-side coupling for 1550 and 2333 nm experimental wavelengths. The first design exhibited a system detection efficiency of ≈ 84.5%, at λ = 1550 nm for the best device measured. The second exhibited low system detection efficiency since the device suffered from unexpectedly high dark count rate mainly due to blackbody radiation at 2.2 K. However, it was possible to measure the timing jitter of this device at 350 mK indicating a FWHM of 84 ps. Another technique to improve the total system detection efficiency of the SNSPD, is by fabricating a hairpin-shaped nanowire atop a single mode waveguide. In this design, photons travel through the waveguide and via evanescent coupling are absorbed in the nanowire. These SNSPD devices have been designed to thread along single mode Si ridge waveguides using a hairpin-shaped nanowire structure, which offers enhanced coupling and absorption efficiency via evanescent coupling. These ultra-thin superconducting MoSi detectors are precisely patterned on top of a single mode Si waveguide (600 nm) with alignment error less than 40 nm. Low temperature electrical and nano-optical characterization was carried out using a two-stage pulse tube (PT) coldhead, using an additional 4He / 3He sorption pump, low vibration characterization of SNSPD devices at 350 mK was carried out. Characterised devices exhibit low dark count rate <5 counts per second and timing jitter of ≈ 83 ps full width half maximum (FWHM) at wavelength (λ) = 1550 nm and at critical current ≈ 30 µA.

•Jan 1, 2019•0 citations
We report a broadband superconducting nanowire single-photon detector for the near-infrared waveband. The optical absorptance in this band is enhanced by utilizing a reflective aluminum mirror and a SiO2layer as an optical cavity. A broadband system detection efficiency (SDE) over 50% from 950 to 1600 nm with a low dark count rate of 10 Hz is realized by coupling a HI 1060 FLEX single-mode fiber. The SDEs reaches 78.3%, 70.9%, and 57.7% at the wavelengths of 1064, 1310, and 1550 nm, respectively. A system timing resolution (jitter) of 83 ps at 1550 nm is obtained. The detector may be useful for broadband applications such as earth observation, environment monitoring, and biomedicine.
Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.
We develop single-photon detectors comprising single-mode fiber-coupled superconducting nanowires, with high system detection efficiencies at a wavelength of 940 nm. The detector comprises a 6.5-nm-thick, 110-nm-wide NbN nanowire meander fabricated onto a Si substrate with a distributed Bragg reflector for enhancing the optical absorptance. We demonstrate that, via the design of a low filling factor (1/3) and active area (Φ = 10 μm), the system reaches a detection efficiency of ∼60% with a dark count rate of 10 Hz, a recovery time <12 ns, and a timing jitter of ∼50 ps.
We report the development of the multimode fiber-coupled superconducting nanowire single-photon detector with high system detection efficiency at visible wavelength. The detector consists of a 10.5-nm-thick and 150-nm-wide NbN nanowire meander fabricated on a Si substrate with a multilayer dielectric mirror and a quarter wavelength cavity for obtaining high optical absorptance. The meander area was 35 µm in diameter and coupled with the GRIN-lensed multimode optical fiber with a core diameter of 50 µm. The system reached detection efficiency of 70% with dark count rate of 100 Hz at the wavelength of 635 nm, 3 dB roll-off response counting rate of 8.5 Mcps, and timing jitter of 76 ps.
Broadband photon detectors are a key enabling technology for various applications such as spectrometers, light detection and ranging. In this work, we report on an ultra-broadband single-photon detector based on a microfiber (MF)-coupled superconducting nanowires structure operating in the spectral range from visible to near-infrared light. The MF-coupled superconducting nanowire single-photon detector (SNSPD) is formed by placing an MF on top of superconducting niobium nitride (NbN) nanowires, allowing ultra-broadband photon detection due to their nearly lossless transmission/absorption and nearly unity internal efficiency for ultra-broad waveband. The simulation results indicate that with optimal device structure, the optical absorption with efficiency > 90% can be realized over a wavelength range of 350 nm to 2150 nm. The fabricated MF-coupled SNSPD shows unparalleled broadband system detection efficiencies (SDEs) of more than 50% from 630 nm to 1500 nm. The SDEs reach 66% at 785 nm and 45% at 1550 nm. These results pave the way for ultra-broadband weak light detection with quantum-limit sensitivity.
We present high performance fiber-coupled niobium titanium nitride superconducting nanowire single photon detectors fabricated on thermally oxidized silicon substrates. By applying a double sided cavity structure, simulated absorptance in the nanowire meander reached 97% at 1550 nm wavelength. The fabricated device showed a system detection efficiency (DE) of 74% at 1550 nm, dark count rate of 100 c/s, and a full width at half maximum timing jitter of 68 ps under a bias current of 18.0 μA with a practical Gifford-McMahon cryocooler system.
Single photon detection advanced rapidly in the last decade. The superconducting nanowire single-photon detector (SNSPD) is an emerging technology, which offers low dark count rates, broadband sensitivity from visible to mid-infrared wavelengths and very high quantum efficiency. All these features are appealing for future emerging applications in remote gas sensing, quantum key distribution and quantum information processing. By enclosing the detector in an optical cavity, tuned to the operating wavelength, the total system detection of the SNSPD is improved. Based on the cavity design, the detector absorption is boosted at the desired experimental wavelength. Devices have been fabricated and tested, in this thesis, with enhanced detection efficiency at near-infrared, infrared and mid-infrared wavelengths. NbTiN detectors fabricated on Ta2O5 / SiO2 distributed Bragg reflectors (DBR) for front-side coupling exhibit a system detection efficiency of ≈ 90% at λ = 940 nm for the best device measured. SNSPDs were also fabricated in NbTiN on metallic mirrors for back-side coupling for 1550 and 2333 nm experimental wavelengths. The first design exhibited a system detection efficiency of ≈ 84.5%, at λ = 1550 nm for the best device measured. The second exhibited low system detection efficiency since the device suffered from unexpectedly high dark count rate mainly due to blackbody radiation at 2.2 K. However, it was possible to measure the timing jitter of this device at 350 mK indicating a FWHM of 84 ps. Another technique to improve the total system detection efficiency of the SNSPD, is by fabricating a hairpin-shaped nanowire atop a single mode waveguide. In this design, photons travel through the waveguide and via evanescent coupling are absorbed in the nanowire. These SNSPD devices have been designed to thread along single mode Si ridge waveguides using a hairpin-shaped nanowire structure, which offers enhanced coupling and absorption efficiency via evanescent coupling. These ultra-thin superconducting MoSi detectors are precisely patterned on top of a single mode Si waveguide (600 nm) with alignment error less than 40 nm. Low temperature electrical and nano-optical characterization was carried out using a two-stage pulse tube (PT) coldhead, using an additional 4He / 3He sorption pump, low vibration characterization of SNSPD devices at 350 mK was carried out. Characterised devices exhibit low dark count rate <5 counts per second and timing jitter of ≈ 83 ps full width half maximum (FWHM) at wavelength (λ) = 1550 nm and at critical current ≈ 30 µA.