Atoms form the basis of precise measurement for many quantities (time, acceleration, rotation, magnetic field, etc.). Measurements of microwave frequency electric fields by traditional methods (i.e. engineered antennas) have limited sensitivity and can be difficult to calibrate properly. Highly-excited (Rydberg) neutral atoms have very large electric-dipole moments and many dipole allowed transitions in the range of 1 - 500 GHz. It is possible to sensitively probe the electric field in this range using the combination of two quantum interference phenomena: electromagnetically induced transparency and the Autler-Townes effect. This technique allows for very sensitive field amplitude, polarization, and sub-wavelength imaging measurements. These quantities can be extracted by measuring properties of a probe laser beam as it passes through a warm rubidium vapor cell. Thus far, Rydberg microwave electrometry has relied upon the absorption of the probe laser. We report on our use of polarization rotation, which corresponds to the real part of the susceptibility, for measuring the properties of microwave frequency electric fields. Our simulations show that when a magnetic field is present and directed along the optical propagation direction a polarization rotation signal exists and can be used for microwave electrometry. One central advantage in using the polarization rotation signal rather than the absorption signal is that common mode laser noise is naturally eliminated leading to a potentially dramatic increase in signal-to-noise ratio.
Atoms form the basis of precise measurement for many quantities (time, acceleration, rotation, magnetic field, etc.). Measurements of microwave frequency electric fields by traditional methods (i.e. engineered antennas) have limited sensitivity and can be difficult to calibrate properly. Highly-excited (Rydberg) neutral atoms have very large electric-dipole moments and many dipole allowed transitions in the range of 1 - 500 GHz. It is possible to sensitively probe the electric field in this range using the combination of two quantum interference phenomena: electromagnetically induced transparency and the Autler-Townes effect. This technique allows for very sensitive field amplitude, polarization, and sub-wavelength imaging measurements. These quantities can be extracted by measuring properties of a probe laser beam as it passes through a warm rubidium vapor cell. Thus far, Rydberg microwave electrometry has relied upon the absorption of the probe laser. We report on our use of polarization rotation, which corresponds to the real part of the susceptibility, for measuring the properties of microwave frequency electric fields. Our simulations show that when a magnetic field is present and directed along the optical propagation direction a polarization rotation signal exists and can be used for microwave electrometry. One central advantage in using the polarization rotation signal rather than the absorption signal is that common mode laser noise is naturally eliminated leading to a potentially dramatic increase in signal-to-noise ratio.
Significant progress has been made in atom-based measurements of length, time, gravity and electromagnetic fields in recently years. Rydberg atom-based microwave electric field measurement, using electromagnetically induced transparency (EIT) in room temperature alkali-metal vapors, has been extensively investigated and aroused the broad interest. This approach may establish a new standard for the measurements of microwave (MW) and radio frequency (RF) electric fields.In this review, we describe the work on a new method of measuring electric fields based on quantum interference by using either cesium or rubidium atoms contained in a dielectric vapor cell. Rydberg atoms with principal quantum number n >>1 have large direct current (DC) polarizabilities and microwave transition dipole moments, thereby making them extremely sensitive to external electric fields. Using the Rydberg three-level EIT to detect the level splitting and shift that is induced by the external field, we can realize a rapid and robust self-calibration method of measuring the electric field in a frequency range from 0.01 GHz to 1000 GHz. For the MW electric field (frequency range > 1 GHz), the MW field causes the Rydberg states to split, known as an Autler-Townes splitting (A-T) effect when the applied microwave can resonate with adjacent Rydberg states. The MW coupled A-T splitting is proportional to the applied electric field strength, from which the field strength is measured. Using the EIT window, a high sensitivity of 3 μV·cm-1·Hz-1/2 and small electric field of 1 μV/cm are expected to be achieved with a modest setup, and the limitations of the sensitivity are also addressed in the review. For the RF field at frequency mj EIT lines, and avoided crossings formed with the fine-structure levels of equal mj and different J's, which is used to calibrate and measure the RF field amplitude. On the other hand, the dependence of the EIT-line strength on the RF field polarization provides a fast and robust polarization measurement of RF fields based on matching experimental data with a theoretical simulation. The measurements of minimum strengths and sensitivity of RF fields based on Rydberg atoms are one order magnitude below the values obtained by traditional antenna methods. The atom-based field measurement paves the way for determining fields through calibration-free, invariable atomic properties and miniaturization. We also propose its various potential applications in the future.
Atom in Rydberg state has large polarizability, large electric dipole and low ionization threshold field. It is very sensitive to electric field, therefore it can be used to measure the amplitude of electric field, especially the microwave electric field. The new developed scheme is based on quantum interference effects (electromagnetically induced transparency and Autler-Townes splitting) in Rydberg atoms. Instead of the direct amplitude measurement, this method tests the Rabi frequency value of the transmission spectrum which is determined by the microwave electric field strength and the corresponding atom nature. The minimum measured strengths of microwave electric fields are far below the standard values obtained by traditional antenna methods. Compared with the traditional methods, this new scheme has several advantages, such as self-calibration, non-perturbation to the measured field and independence of the probe length. Besides, this scheme can also be used to measure the polarization direction of microwave electric field and realize sub-wavelength imaging. Through adjusting the wavelength of coupling laser, a broadband 1-500 GHz microwave electric field measurement can be achieved. This new scheme is benefitial to conducting the continue electric field measurement and the miniaturization of the test equipment. In this paper, the researches about using Rydberg atom to measure electric field with high precision are reviewed. The basic theory and experimental techniques are introduced. Finally, we discuss a promising method of using Rydberg atom interferometer to detect the accumulated phase in the process of interaction between electric field and Rydberg atoms. This method converts amplitude measurement into phase test, which may improve the precision and sensitivity.
We have shown that Rydberg states can be used for high-sensitivity, absolute sensing of microwave (MW) electric fields. We achieved a sensitivity of 3 μVcm-1Hz-1/2 for two read-out strategies. Depending on the spectral resolution of the read-out, either the MW induced transmission line frequency splitting, the Autler-Townes regime, or a change in the on-resonant absorption, the amplitude regime, can be used to determine the MW electric field. Results using a Mach-Zehnder interferometer and frequency modulated spectroscopy both achieve similar photon shot noise limited sensitivity. In addition, we have also explored amplitude modulation and the displacement of a probe laser beam due to index of refraction changes in a prism shaped vapor cell. These latter methods were not able to achieve photon shot noise limited performance. Fundamental limits to the sensitivity of the Rydberg atom-based MW electric field sensing have been addressed, but it is important to clarify the differences between noise in different parts or subsystems of the sensor. Shot noise in the probe laser usually dominates the projection noise of the atoms participating in the measurement of the MW electric field because of the desire to operate at low effective Rydberg atom densities in order to avoid collisional dephasing and ionization.
Rydberg atoms are neutral atoms excited to high principal quantum number states, which endows them with exaggerated properties such as large electric dipole moments, long lifetimes, and extreme sensitivity to external electromagnetic fields. These characteristics form the foundation of Rydberg atom-based sensors, an emerging class of quantum devices capable of optically detecting electric fields across frequencies from DC to the terahertz regime. Rydberg-based electrometry operates through both Autler–Townes (AT) splitting of resonant Rydberg transitions and Stark-shift measurements for high-frequency or far-detuned fields, enabling broadband field sensing from DC to the THz regime. Using ladder-type electromagnetically induced transparency (EIT) and AT splitting, these sensors enable non-invasive, SI-traceable measurements of field amplitude, frequency, phase, and polarization. Recent developments have demonstrated broadband electric field probes, voltage calibration standards, and compact RF receivers based on thermal vapor cells and integrated photonic architectures. Furthermore, innovations in multi-photon EIT, superheterodyne readout, and multi wave mixing have expanded the dynamic range and bandwidth of Rydberg-based electrometry. Despite challenges related to environmental perturbations, linewidth broadening, and laser stabilization, ongoing advances in atomic control, hybrid photonic integration, and EIT-based readout promise scalable, chip-compatible sensors. This review summarizes the physical principles, experimental progress, and emerging applications of Rydberg atom-based sensing, emphasizing their potential for next generation quantum metrology, wireless communication, and precision field mapping.
A highly excited Rydberg atom via electromagnetically induced transparency with two color cascading lasers has extreme sensitivity to electric fields of microwave ranging from 100 MHz to over 1 THz. It can be used as susceptible atom-based microwave communication antennas where the carrier wave usually works exactly resonant to the transition between a pair of adjacent Rydberg states with large electric dipole moment. A technique of superheterodyne with a strong on-resonant local microwave oscillator is employed to induce considerable Autler-Townes splitting where the antennas has a highest dynamic response to another weak target signal microwave carrier. To further improve the sensitivity of atomic antenna in communication, we detune the carrier microwave frequency off resonance forming an asymmetrically optical splitting and fix the coupling laser frequency at the shoulder of the stronger one, and optimize the local field strength simultaneously. It gives a sensitivity of 12.50(04) nVcm−1⋅Hz−1/2. Its enhancement mechanism of sensitivity is also proved by a theoretical simulation.
Quantum systems obeying well-defined laws of physics are very attractive metrological sensors. In principle, they are intrinsically calibrated and allow direct traceability to the SI system. Several fundamental and derived units are nowadays already based on the properties of quantum systems. Neutral atoms are e.g. used for the realization of the second. Leveraging the advantageous properties of such systems to other derived units and establishing traceability still represents a significant challenge, as real-life macroscopic scales must be linked with the microscopic quantum world. In this work, we investigate the use of a vapor of neutral atoms as a highly sensitive probe for electric fields in the microwave domain. By optically exciting the atoms to high-energy states—known as Rydberg states—the atoms become extremely sensitive to electric fields due to their large electric dipole moment. Through optical readout of the atomic state, this enhanced sensitivity can be exploited to turn the atoms into precise sensors for electric fields. In contrast to classical methods of measuring electric fields using metallic probes or antennas, a dilute atomic vapor has the distinct advantage of exerting only minimal influence on the fields being measured. In this study, we aim to leverage these benefits in an experiment designed to measure microwave electric field distributions above a coplanar waveguide structure with high precision and spatial resolution. In order to translate the high accuracy of the atomic sensors to accurate measurements of electrical parameters of the coplanar structure like power, voltage standing wave ratio or S-parameters, we plan to integrate the coplanar waveguide structure into a large atomic vapor cell where it is directly surrounded by the atomic gas. In this case the fields are only minimally disturbed by the vapor cell itself and allow for simple models to translate field measurements into electrical measurements. The methods we are developing in this project are not only aiming to provide traceable measurements for high frequency electrometry but also have the potential to be extended to higher frequency in the terahertz regime or to high resolution imaging of electric field distributions.