In recent years, the amount of digital data which is stored and transmitted for private and public usage has increased considerably. To allow a save transmission and storage of data despite of error-prone transmission media, error correcting codes are used. A large variety of codes has been developed, and in the past decade low-density parity-check (LDPC) codes which have an excellent error correction performance became more and more popular. Today, low-density parity-check codes have been adopted for several standards, and efficient decoder hardware architectures are known for the chosen structured codes. However, the existing decoder designs lack flexibility as only few structured codes can be decoded with one decoder chip. In consequence, different codes require a redesign of the decoder, and few solutions exist for decoding of codes which are not quasi-cyclic or which are unstructured. In this thesis, three different approaches are presented for the implementation of fully programmable LDPC decoders which can decode arbitrary LDPC codes. As a design study, the first programmable decoder which uses a heuristic mapping algorithm is realized on a field-programmable gate array (FPGA), and error correction curves are measured to verify the correct functionality. The main contribution of this thesis lies in the development of the second and the third architecture and an appropriate mapping algorithm. The proposed fully programmable decoder architectures use one-phase message passing and layered decoding and can decode arbitrary LDPC codes using an optimum mapping and scheduling algorithm. The presented programmable architectures are in fact generalized decoder architectures from which the known decoder architectures for structured LDPC codes can be derived.
In recent years, the amount of digital data which is stored and transmitted for private and public usage has increased considerably. To allow a save transmission and storage of data despite of error-prone transmission media, error correcting codes are used. A large variety of codes has been developed, and in the past decade low-density parity-check (LDPC) codes which have an excellent error correction performance became more and more popular. Today, low-density parity-check codes have been adopted for several standards, and efficient decoder hardware architectures are known for the chosen structured codes. However, the existing decoder designs lack flexibility as only few structured codes can be decoded with one decoder chip. In consequence, different codes require a redesign of the decoder, and few solutions exist for decoding of codes which are not quasi-cyclic or which are unstructured. In this thesis, three different approaches are presented for the implementation of fully programmable LDPC decoders which can decode arbitrary LDPC codes. As a design study, the first programmable decoder which uses a heuristic mapping algorithm is realized on a field-programmable gate array (FPGA), and error correction curves are measured to verify the correct functionality. The main contribution of this thesis lies in the development of the second and the third architecture and an appropriate mapping algorithm. The proposed fully programmable decoder architectures use one-phase message passing and layered decoding and can decode arbitrary LDPC codes using an optimum mapping and scheduling algorithm. The presented programmable architectures are in fact generalized decoder architectures from which the known decoder architectures for structured LDPC codes can be derived.
Low-Density Parity-Check (LDPC) codes have recaptured the attention of the scientific community a few years after Turbo codes were invented in the early nineties. Originally proposed in the 1960s at MIT by R. Gallager, LDPC codes represent powerful error correcting codes that allow working very close to the Shannon limit and achieve excellent Bit Error Rate (BER) due to computationally intensive algorithms on the decoder side of the system. Advances in microelectronics introduced small process technologies that allowed developing complex designs incorporating a high number of transistors in Very Large Scale Integration (VLSI) systems. Recently, these processes have been used to develop architectures able of performing LDPC decoding in real-time and delivering considerably high throughputs. Mainly for these reasons and naturally because the patent has expired, they have been adopted by modern communication standards which triggered their popularity, showing how actual they are. Due to the increase of transistor density in VLSI systems, and also to the fact that recently processing speed has risen faster than bandwidth, power and memory walls have created a new paradigm in computer architectures: rather than just increasing the frequency of operation supported by smaller process designs, the introduction of multiple cores on a single chip has become the new trend to provide augmented computational power. This thesis proposes new approaches for these computationally intensive algorithms, by performing parallel LDPC decoding based on ubiquitous multi-core architectures and achieves efficient throughputs that compare well with dedicated VLSI systems. We extensively address the challenges faced in the investigation and development of these programmable solutions, with focus mainly given on flexibility and scalability of the proposed algorithms, throughput and BER performance, and general efficiency of the programmable solutions here presented, that also achieve results more than an order of magnitude superior to those obtained with conventional CPUs. Furthermore, the investigation herein described follows a methodology that analyzes in detail the computational complexity of these decoding algorithms in order to propose strategies to accelerate their processingwhich, if conveniently transposed to other areas of computer science, can demonstrate that in this new multi-core era we may be in the presence of valid alternatives to non-reprogrammable dedicated VLSI hardware that requires non-recurring engineering.
Future technologies such as cognitive radio require flexible and reliable hardware architectures that can be easily configured and adapted to varying coding parameters.The objective of this work is to develop a flexible hardware encoder and decoder for low-density parity-check (LDPC) codes.The design methodologies used for the implementation of a LDPC encoder and decoder are flexible in terms of parity-check matrix, code rate and code length.All these designs are implemented on a programmable chip and tested.Encoder implementations of LDPC codes are optimized for area due to their high complexity.Such designs usually have relatively low data rate.Two new encoder designs are developed that achieve much higher data rates of up to 844 Mbps while requiring more area for implementation.Using structured LDPC codes decreases the encoding complexity and provides design flexibility.The architecture for an encoder is presented that adheres to the structured LDPC codes defined in the IEEE 802.16e standard.A single encoder design is also developed that accommodates different code lengths and code rates and does not require re-synthesis of the design in order to change the encoding parameters.The flexible encoder design for structured LDPC codes is also implemented on a custom chip.The maximum coded data rate of the structured encoder is up to 844 Mbps and for a given code rate its value is independent of the code length.An LDPC decoder is designed and its design methodology is generic.It is applicable to both structured and any randomly generated LDPC codes.The coded data rate of the decoder increases with the increase in the code length.The number of decoding iterations used for the decoding process plays an important role in determining the decoder performance and latency.This design validates the estimated codeword after every iteration and stops the decoding process when the correct codeword is estimated which saves power consumption.For a given paritycheck matrix and signal-to-noise ratio, a procedure to find an optimum value of the maximum number of decoding iterations is presented that considers the affects of power, delay, and error performance.
Low-density parity-check (LDPC) codes have been shown to have good error correcting performance approaching Shannon’s limit. Good error correcting performance enables efficient and reliable communication. However, a LDPC code decoding algorithm needs to be executed efficiently to meet cost, time, power and bandwidth requirements of target applications. The constructed codes should also meet error rate performance requirements of those applications. Since their rediscovery, there has been much research work on LDPC code construction and implementation. LDPC codes can be designed over a wide space with parameters such as girth, rate and length. There is no unique method of constructing LDPC codes. Existing construction methods are limited in some way in producing good error correcting performing and easily implementable codes for a given rate and length. There is a need to develop methods of constructing codes over a wide range of rates and lengths with good performance and ease of hardware implementability. LDPC code hardware design and implementation depend on the structure of target LDPC code and is also as varied as LDPC matrix designs and constructions. There are several factors to be considered including decoding algorithm computations,processing nodes interconnection network, number of processing nodes, amount of memory, number of quantization bits and decoding delay. All of these issues can be handled in several different ways. \nThis thesis is about construction of LDPC codes and their hardware implementation. LDPC code construction and implementation issues mentioned above are too many to be addressed in one thesis. The main contribution of this thesis is the development of LDPC code construction methods for some classes of structured LDPC codes and techniques for reducing decoding time. We introduce two main methods for constructing structured codes. In the first method, column-weight two LDPC codes are derived from distance graphs. A wide range of girths, rates and lengths are obtained compared to existing methods. The performance and implementation complexity of obtained codes depends on the structure of their corresponding distance graphs. In the second method, a search algorithm based on bit-filing and progressive-edge growth algorithms is introduced for constructing quasi-cyclic LDPC codes. The algorithm can be used to form a distance or Tanner graph of a code. This method could also obtain codes over a wide range of parameters. Cycles of length four are avoided by observing the row-column constraint. \nRow-column connections observing this condition are searched sequentially or randomly. Although the girth conditions are not sufficient beyond six, larger girths codes were easily obtained especially at low rates. The advantage of this algorithm compared to other methods is its flexibility. It could be used to construct codes for a given rate and length with girths of at least six for any sub-matrix configuration or rearrangement. The code size is also easily varied by increasing or decreasing sub-matrix size. Codes obtained using a sequential search criteria show poor performance at low girths (6 and 8) while random searches result in good performing codes. \nQuasi-cyclic codes could be implemented in a variety of decoder architectures. One of the many options is the choice of processing nodes interconnect. We show how quasi-cyclic codes processing could be scheduled through a multistage network. Although these net-works have more delay than other modes of communication, they offer more flexibility at a reasonable cost. Banyan and Benes networks are suggested as the most suitable networks. \nDecoding delay is also one of several issues considered in decoder design and implementation. In this thesis, we overlap check and variable node computations to reduce decoding time. Three techniques are discussed, two of which are introduced in this thesis. The techniques are code matrix permutation, matrix space restriction and sub-matrix row-column scheduling. Matrix permutation rearranges the parity-check matrix such that rows and columns that do not have connections in common are separated. This techniques can be applied to any matrix. Its effectiveness largely depends on the structure of the code. We show that its success also depends on the size of row and column weights. Matrix space restriction is another technique that can be applied to any code and has fixed reduction in time or amount of overlap. Its success depends on the amount of restriction and may be traded with performance loss. The third technique already suggested in literature relies on the internal cyclic structure of sub-matrices to achieve overlapping. The technique is limited to LDPC code matrices in which the number of sub-matrices is equal to row and column weights. We show that it can be applied to other codes with a lager number of sub-matrices than code weights. However, in this case maximum overlap is not guaranteed. We calculate the lower bound on the amount of overlapping. Overlapping could be applied to any sub-matrix configuration of quasi-cyclic codes by arbitrarily choosing \nthe starting rows for processing. Overlapping decoding time depends on inter-iteration waiting times. We show that there are upper bounds on waiting times which depend on the code weights. Waiting times could be further reduced by restricting shifts in identity sub-matrices or using smaller sub-matrices. This overlapping technique can reduce the decoding time by up to 50% compared to conventional message and computation scheduling. \nTechniques of matrix permutation and space restriction results in decoder architectures that are flexible in LDPC code design in terms of code weights and size. This is due to the fact that with these techniques, rows and columns are processed in sequential order to achieve overlapping. However, in the existing technique, all sub-matrices have to be processed in parallel to achieve overlapping. Parallel processing of all code sub-matrices requires the architecture to have the number of processing units at least equal to the number sub-matrices. Processing units and memory space should therefore be distributed among the sub-matrices according to the sub-matrices arrangement. This leads to high complexity or inflexibility in the decoder architecture. We propose a simple, programmable and high throughput decoder architecture based on matrix permutation and space restriction techniques.
Low-density parity-check (LDPC) codes have been widely considered as error-correcting codes for next generation communication systems. A good LDPC decoder design requires both implementation friendly LDPC codes and efficient decoder architectures. The quality of LDPC code is crucial in determining the coding gain and implementation complexity of LDPC hardware decoders. This paper presented a genetic algorithm (GA) based LDPC code search algorithm with hardware considerations. Regular quasi-cyclic LDPC codes are used due to its friendliness to hardware implementation. Our hardware architecture design schedules pipeline LDPC decoding operation to boost the hardware utilization efficiency (HUE) of LDPC decoder. A LDPC decoder with a block size of 12288 is implemented in FPGA to validate our code and architecture design.
This paper studies low-complexity high-speed decoder architectures for quasi-cyclic low density parity check (QC-LDPC) codes. Algorithmic transformation and architectural level optimization are incorporated to reduce the critical path. Enhanced partially parallel decoding architectures are proposed to linearly increase the throughput of conventional partially parallel decoders through introducing a small percentage of extra hardware. Based on the proposed architectures, a (8176, 7154) Euclidian geometry-based QC-LDPC code decoder is implemented on Xilinx field programmable gate array (FPGA) Virtex-II 6000, where an efficient nonuniform quantization scheme is employed to reduce the size of memories storing soft messages. FPGA implementation results show that the proposed decoder can achieve a maximum (source data) decoding throughput of 172 Mb/s at 15 iterations
The Low-Density Parity-Check codes are among the most powerful forward error correcting codes, since they enable to get as close as a fraction of a dB from the Shannon limit.This astonishing performance combined with their relatively simple decoding algorithmmake these codes very attractive for the next digital transmission system generations. Itis already the case for the next digital satellite broadcasting standard (DVB-S2), where an irregular LDPC code has been chosen to protect the downlink information. In this thesis, we focused our research on the iterative decoding algorithms and their hardware implementations. We proposed first a suboptimal algorithm named the λ-min algorithm. It reduces significantly the complexity of the decoder without any significant performance loss, as compared to the belief propagation (BP) algorithm. Then we studied and designed a generic architecture of an LDPC decoder, which has been implemented on a FPGA based platform. This hardware decoder enables to accelerate the simulations more than 500 times as compared to software simulations. Moreover, based on an all-tunable design, our decoder features many facilities: It is possible to configure it for a very wide code family, so that the research for good codes is processed faster ; thanks to the genericity of the processing components, it is also possible to optimize the internal coding format, and even to compare various decoding algorithms and various processing schedules. Finally, our experience in the area of LDPC decoders led us to propose a formal framework for analysing the architectures of LDPC decoders. This framework encompassesboth the datapath (parallelism, node processors architectures) and the control mode associated to the several decoding schedules. Thus within this framework, a classification of the different state-of-the-art LDPC decoders is proposed. Moreover, some synthesis of efficient and unpublished architectures have been also proposed.