Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

A quasioptical SIS receiver with normal metal tuning for the 800-900 GHz band

Frank Schafer, P. van der Wal, E. Kreysa, K. H. Gundlach

Published Jan 1, 1997• 4 citations
OpenAlex

Abstract

The receiver employs the well established design of using a diffraction limited substrate-lens made of crystalline quartz fed by a double-slot antenna to couple to the incoming radiation [1]-[3]. In contrast to the design variant using silicon as lens material [4], our antenna configuration includes a moveable reflecting backplane to avoid losses due to the backward radiation into the vacuum side. Without backplane these losses would be higher as compared to silicon due to the lower refractive index of the quartz dielectric; on the other hand for the silicon lens an antireflection coating usually has to be applied to reduce the higher reflection loss of the silicon lens. Currently we use no antireflection coating on the quartz lens. A schematic drawing of our optical setup is shown in Fig. 1. It was designed using a theoretical method developed by Prof. V. Hansen and his group [5], which gives the antenna's impedance and its radiation characteristic into a dielectric half space. Results from the calculation of the double-slot input impedance versus reflector distance are shown in Fig. 2. The extended hyperhemispherical lens was shown to provide good quality amplitude and phase patterns by scaled measurements at microwave frequencies [6].

Related papers

Antireflection—Coated Silicon Lenses for Low—Noise 400 — 1040 GHz Quasioptical SIS Mixers

Mei Bin, Michael C. Gaidis, Henry George LeDuc +2 more

A significant improvement in the optical efficiency of quasioptical SIS mixers can be obtained by using a substrate lens made with a high dielectric constant material such as silicon (€ 11.5), along with a suitable antireflection coating. The large dielectric constant of the substrate lens increases the forward coupling efficiency of the integrated antenna, to around 90% for a twin-slot on silicon. However, an antireflection coating is needed to avoid a 30% reflection loss at the lens surface. This coating must satisfy several important constraints: (1) The coating material must have the correct dielectric constant (e 3.4); (2) The material must adhere well to the lens and be cryogenically recyclable; and (3) The coating thickness should be controlled to an accuracy of a few microns. Ugras, Zmuidzinas, and LeDuc (1994) showed that suitable coatings could be made using alumina-loaded epoxy that is diamond-machined to the correct thickness, and demonstrated results in the 500-600 GHz band. Since then, we have employed this technique with all-niobium SIS mixers in the 400-850 GHz band (Gaidis et al. 1996), and with a 1042 Gliz SIS mixer using niobium junctions and an aluminum tuning circuit (Bin et al. 1996). We will describe measurements of the frequency response, nase temperature, and antenna pattern and polarization. In our experience, the coatings are very rugged and reliable. These mixers have been used over the past two years for astronomical observations aboard NASA's Kuiper Airborne Observatory.

Softwaretechnik-Trends•Mar 1, 1996•0 citations

Slot antenna SIS mixers for submillimeter wavelengths

Jonas Stasys Zmuidzinas, Henry George LeDuc, Jeff A. Stern

We are developing improved versions of a slot antenna SIS mixer which we have previously described. The initial work demonstrated a double sideband noise temperature of 420 K for a 500 GHz quasi-optical SIS mixer employing a twin-slot antenna on a quartz dielectric substrate. A quartz hyperhemispherical lens is used to focus the incoming radiation onto the twin-slot antenna. The advantages of a twin-slot antenna include a low impedance (35 omega) and a clean, symmetric beam pattern into the dielectric with a 70 percent efficiency. In our original mixer, the radiation was coupled from the two slot antennas onto superconducting microstrip lines which fed the SIS junction. By performing an impedance transformation using tapered lines and by feeding the radiation from the two slots to the junction in parallel, the effective (real) impedance seen by the junction was reduced to just 4 omega. This very low impedance allowed a junction area of 2.3 sq micron to be used at 500 GHz, which was manufactured using optical lithography. However, no attempt was made to tune out the junction capacitance. We estimate that this capacitance reduces the impedance coupling efficiency to eta(sub Z) approx. equals 0.23, for our junction with omega R(sub N) C = 5.3 at 500 GHz. The recent development of techniques using electron-beam lithography to manufacture junctions with very small areas (approx. equals 0.1 sq microns) now allows considerably more flexibility in the design of SIS mixer circuits. We have redesigned the slot-antenna mixer to take advantage of this possibility. In particular, we have included a novel circuit which allows the junction capacitance to be tune out over a broad bandwidth. For instance, mixers designed for 800 GHz using NbN/MgO/NbN junctions with realistic parameters achieve a 3 dB impedance bandwidth of nearly 400 GHz. Furthermore, our circuit uses only short lengths of microstrip and should be less sensitive to RF losses than other designs. The improved impedance match should give a large reduction in noise temperature as compared to our previous mixer. The new devices are currently under fabrication. Further details of the design and any available experimental results are discussed.

Softwaretechnik-Trends•Jan 1, 1992•4 citations

Design and Characterization of a Quasi-Optical SIS Receiver for the 1 THz Band

M. Bin, Michael C. Gaidis, Daniel Miller +3 more

91101. Abstract—We report on the design and characterization of broadband quasi-optical SIS receirvers for the 1 THz frequency band. The mixer design utilizes a twin-slot antenna, an antirefiection-coated silicon hyperhemispherical lens, Nb/Al-oxide/Nb tunnel junctions, and an aluminum normal-metal tuning circuit in a two-junction configuration. The fre- quency response of the device was measured using a Fourier transform spectrometer and agrees reasonably well with the theoretical prediction. Heterodyne tests were carried out from 822-1042 GHz and low receiver noise temperatures of about 770 K were obtained after correcting the losses from the LO/signal beamsplitter.

Softwaretechnik-Trends•Mar 1, 1996•3 citations

Quasi-optical SIS mixers with normal metal tuning structures

Mei Bin, Michael C. Gaidis, Jonas Stasys Zmuidzinas +2 more

We recently reported (1996) a quasi-optical SIS mixer which used Nb/Al-oxide/Nb tunnel junctions and a normal-metal (Al) tuning circuit to achieve an uncorrected receiver noise temperature of 840 K (DSB) at 1042 GHz. Here we present results on several different device designs, which together cover the 300-1200 GHz frequency range. The mixers utilize an antireflection-coated silicon hyper-hemispherical lens, a twin-slot antenna, and a two-junction tuning circuit. The broad-band frequency response was measured using Fourier transform spectrometry (FTS), and is in good agreement with model calculations. Heterodyne tests were carried out from 400 GHz up to 1040 GHz, and these measurements agree well with the FTS results and with calculations based on Tucker's theory (1985).

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•23 citations

Low-noise slot antenna SIS mixers

Jonas Stasys Zmuidzinas, N. G. Ugras, D. Miller +3 more

We describe quasi-optical SIS mixers operating in the submillimeter band (500-750 GHz) which have very low noise, around 5 h/spl nu//k/sub B/ for the double-sideband receiver noise temperature. The mixers use a twin-slot antenna, Nb/Al-Oxide/Nb tunnel junctions fabricated with optical lithography, a two-junction tuning circuit, and a silicon hyperhemispherical lens with a novel antireflection coating to optimize the optical efficiency. We have flown a submillimeter receiver using these mixers on the Kuiper Airborne Observatory, and have detected a transition of H/sub 2//sup 18/O at 745 GHz. This directly confirms that SIS junctions are capable of low-noise mixing above the gap frequency.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•55 citations

Quasi-optical log-periodic antenna SIS mixers for the 100 GHz band

Yoshinori Uzawa, Taiichiro Noguchi, Akira Kawakami +1 more

We designed and tested a quasi-optical SIS mixer that incorporates a substrate lens for the 100 GHz band. The mixer uses a planar self-complementary log-periodic antenna with an integrated tuning circuit. The antenna has a frequency independent impedance of around over several octaves. The tuning circuit consists of two SIS junctions connected in parallel through a superconducting stripline inductor for tuning out the junction capacitances and a impedance transformer for matching the junction resistance to the antenna impedance. The SIS junctions are and have an area of and a current density of . The IF output from the mixer is brought out in a balanced way at each edge of the antenna, and is coupled to a cooled low-noise amplifier through a balun transformer by using a hybrid coupler. A double-sideband receiver noise temperature less than 130 K was measured from 85 to 110 GHz. The best noise temperature was 90 K at 101 GHz, which is the same as for waveguide receivers.

Superconductor Science and Technology•Apr 1, 1996•5 citations
The receiver employs the well established design of using a diffraction limited substrate-lens made of crystalline quartz fed by a double-slot antenna to couple to the incoming radiation [1]-[3]. In contrast to the design variant using silicon as lens material [4], our antenna configuration includes a moveable reflecting backplane to avoid losses due to the backward radiation into the vacuum side. Without backplane these losses would be higher as compared to silicon due to the lower refractive index of the quartz dielectric; on the other hand for the silicon lens an antireflection coating usually has to be applied to reduce the higher reflection loss of the silicon lens. Currently we use no antireflection coating on the quartz lens. A schematic drawing of our optical setup is shown in Fig. 1. It was designed using a theoretical method developed by Prof. V. Hansen and his group [5], which gives the antenna's impedance and its radiation characteristic into a dielectric half space. Results from the calculation of the double-slot input impedance versus reflector distance are shown in Fig. 2. The extended hyperhemispherical lens was shown to provide good quality amplitude and phase patterns by scaled measurements at microwave frequencies [6].
A significant improvement in the optical efficiency of quasioptical SIS mixers can be obtained by using a substrate lens made with a high dielectric constant material such as silicon (€ 11.5), along with a suitable antireflection coating. The large dielectric constant of the substrate lens increases the forward coupling efficiency of the integrated antenna, to around 90% for a twin-slot on silicon. However, an antireflection coating is needed to avoid a 30% reflection loss at the lens surface. This coating must satisfy several important constraints: (1) The coating material must have the correct dielectric constant (e 3.4); (2) The material must adhere well to the lens and be cryogenically recyclable; and (3) The coating thickness should be controlled to an accuracy of a few microns. Ugras, Zmuidzinas, and LeDuc (1994) showed that suitable coatings could be made using alumina-loaded epoxy that is diamond-machined to the correct thickness, and demonstrated results in the 500-600 GHz band. Since then, we have employed this technique with all-niobium SIS mixers in the 400-850 GHz band (Gaidis et al. 1996), and with a 1042 Gliz SIS mixer using niobium junctions and an aluminum tuning circuit (Bin et al. 1996). We will describe measurements of the frequency response, nase temperature, and antenna pattern and polarization. In our experience, the coatings are very rugged and reliable. These mixers have been used over the past two years for astronomical observations aboard NASA's Kuiper Airborne Observatory.
We are developing improved versions of a slot antenna SIS mixer which we have previously described. The initial work demonstrated a double sideband noise temperature of 420 K for a 500 GHz quasi-optical SIS mixer employing a twin-slot antenna on a quartz dielectric substrate. A quartz hyperhemispherical lens is used to focus the incoming radiation onto the twin-slot antenna. The advantages of a twin-slot antenna include a low impedance (35 omega) and a clean, symmetric beam pattern into the dielectric with a 70 percent efficiency. In our original mixer, the radiation was coupled from the two slot antennas onto superconducting microstrip lines which fed the SIS junction. By performing an impedance transformation using tapered lines and by feeding the radiation from the two slots to the junction in parallel, the effective (real) impedance seen by the junction was reduced to just 4 omega. This very low impedance allowed a junction area of 2.3 sq micron to be used at 500 GHz, which was manufactured using optical lithography. However, no attempt was made to tune out the junction capacitance. We estimate that this capacitance reduces the impedance coupling efficiency to eta(sub Z) approx. equals 0.23, for our junction with omega R(sub N) C = 5.3 at 500 GHz. The recent development of techniques using electron-beam lithography to manufacture junctions with very small areas (approx. equals 0.1 sq microns) now allows considerably more flexibility in the design of SIS mixer circuits. We have redesigned the slot-antenna mixer to take advantage of this possibility. In particular, we have included a novel circuit which allows the junction capacitance to be tune out over a broad bandwidth. For instance, mixers designed for 800 GHz using NbN/MgO/NbN junctions with realistic parameters achieve a 3 dB impedance bandwidth of nearly 400 GHz. Furthermore, our circuit uses only short lengths of microstrip and should be less sensitive to RF losses than other designs. The improved impedance match should give a large reduction in noise temperature as compared to our previous mixer. The new devices are currently under fabrication. Further details of the design and any available experimental results are discussed.
91101. Abstract—We report on the design and characterization of broadband quasi-optical SIS receirvers for the 1 THz frequency band. The mixer design utilizes a twin-slot antenna, an antirefiection-coated silicon hyperhemispherical lens, Nb/Al-oxide/Nb tunnel junctions, and an aluminum normal-metal tuning circuit in a two-junction configuration. The fre- quency response of the device was measured using a Fourier transform spectrometer and agrees reasonably well with the theoretical prediction. Heterodyne tests were carried out from 822-1042 GHz and low receiver noise temperatures of about 770 K were obtained after correcting the losses from the LO/signal beamsplitter.
We recently reported (1996) a quasi-optical SIS mixer which used Nb/Al-oxide/Nb tunnel junctions and a normal-metal (Al) tuning circuit to achieve an uncorrected receiver noise temperature of 840 K (DSB) at 1042 GHz. Here we present results on several different device designs, which together cover the 300-1200 GHz frequency range. The mixers utilize an antireflection-coated silicon hyper-hemispherical lens, a twin-slot antenna, and a two-junction tuning circuit. The broad-band frequency response was measured using Fourier transform spectrometry (FTS), and is in good agreement with model calculations. Heterodyne tests were carried out from 400 GHz up to 1040 GHz, and these measurements agree well with the FTS results and with calculations based on Tucker's theory (1985).
We describe quasi-optical SIS mixers operating in the submillimeter band (500-750 GHz) which have very low noise, around 5 h/spl nu//k/sub B/ for the double-sideband receiver noise temperature. The mixers use a twin-slot antenna, Nb/Al-Oxide/Nb tunnel junctions fabricated with optical lithography, a two-junction tuning circuit, and a silicon hyperhemispherical lens with a novel antireflection coating to optimize the optical efficiency. We have flown a submillimeter receiver using these mixers on the Kuiper Airborne Observatory, and have detected a transition of H/sub 2//sup 18/O at 745 GHz. This directly confirms that SIS junctions are capable of low-noise mixing above the gap frequency.>
We designed and tested a quasi-optical SIS mixer that incorporates a substrate lens for the 100 GHz band. The mixer uses a planar self-complementary log-periodic antenna with an integrated tuning circuit. The antenna has a frequency independent impedance of around over several octaves. The tuning circuit consists of two SIS junctions connected in parallel through a superconducting stripline inductor for tuning out the junction capacitances and a impedance transformer for matching the junction resistance to the antenna impedance. The SIS junctions are and have an area of and a current density of . The IF output from the mixer is brought out in a balanced way at each edge of the antenna, and is coupled to a cooled low-noise amplifier through a balun transformer by using a hybrid coupler. A double-sideband receiver noise temperature less than 130 K was measured from 85 to 110 GHz. The best noise temperature was 90 K at 101 GHz, which is the same as for waveguide receivers.