Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Measurement of jitter in a long Josephson junction soliton oscillator clock source

Jonathan L. Habif, C.A. Mancini, Mark F. Bocko

Published Mar 1, 2001• 5 citations
Publisher

Abstract

Stability of Josephson junction clock sources can be a limiting factor in the operation of RSFQ digital and mixed signal circuits. We have developed techniques for the characterization of the short-term stability, i.e., the jitter, of Josephson junction clock sources, and in this paper we present measurements of the jitter for a long Josephson junction soliton oscillator clock. The output frequency of the soliton oscillator was prescaled by using a chain of T flip-flops and using a current bias feedback the oscillator was phase locked to a stable room temperature RP source. Phase noise spectra of the clock signal were measured at the successive stages of the T flip-flop chain and interpreted to infer the cycle-to-cycle jitter of the soliton oscillator. The jitter at the output of the soliton oscillator was measured to be 60 fs at a frequency of 26 GHz, or 0.16% of the period of the clock.

DOI
10.1109/77.919536

Related papers

Short-term frequency stability of clock generators for multigigahertz rapid-single-flux quantum digital circuits

C.A. Mancini, Mark F. Bocko

Superconducting digital systems based on Josephson junctions have generally used a synchronous timing strategy. A master clock signal is used to delimit a data window during which the system changes state and data is transferred from one block to the next. The temporal stability of the clock signal has a profound effect on the performance of rapid single flux quantum (RSFQ) digital systems. In particular, short-term clock fluctuations, or clock jitter, can degrade system performance due to the hazard of timing constraint violations. The successful development of large-scale RSFQ digital systems will require highly stable multigigahertz on-chip clock sources. To meet this need, methods for characterizing and measuring the short-term stability of such sources are required. We identify the relevant figure of merit to characterize and compare various clocks: the cycle-to-cycle standard deviation of the clock periods. We present experimental techniques for the measurement of this figure of merit and apply them to the measurement of jitter in a clock generator used often in RSFQ systems, the ring oscillator. High-frequency phase noise measurements found the jitter of a 9.6-GHz clock to be in the range from 0.6% to 0.36% of the clock period. The measured values of clock jitter fell within the 95% confidence interval of our stochastic circuit simulations. This was sufficient evidence to conclude that thermal noise from the resistors in the circuit may be the dominant source of jitter in the ring oscillator.

IEEE Transactions on Applied Superconductivity•Mar 1, 2003•8 citations

Short-term frequency stability of RSFQ ring oscillators

C.A. Mancini, Mark F. Bocko

The temporal stability of the clock signal has a profound effect on the performance of synchronous RSFQ digital systems. Short-term clock fluctuations, or clock jitter, can severely degrade system performance due to the hazard of timing constraint violations. Successful large-scale RSFQ digital systems will require highly stable multi-Gigahertz on-chip clock sources. To meet this need, methods for characterizing and measuring the short-term stability of such sources are required. In this paper we identify the relevant figure of merit to characterize and compare various clocks: the cycle-to-cycle standard deviation of the clock periods. We have developed experimental techniques for the measurement of this figure of merit and applied it to the characterization of an RSFQ ring oscillator. The experimental results are compared with results from a stochastic circuit simulator. We determined the value of jitter to be 1.52% at 10 GHz.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•9 citations

Phase-locked operation of RSFQ ring oscillators

Cesar A. Mancini, Mark F. Bocko

Ring oscillators are the traditional on-chip clock source for RSFQ mixed-signal and digital circuits. Their long-term frequency stability is essential for certain signal processing applications such as the sampling clock for an A/D converter or the output clock of a D/A converter. However conventional bias schemes lead to excessive drift in the frequency. Embedding the ring oscillator in a phase-locked loop (PLL) circuit allows it to inherit the frequency stability of an external reference source. An RSFQ circuit comprised of a ring oscillator, a divide-by-2 20 prescaler and a resynchronizer D flip-flop was fabricated using the standard 1 kA cm -2 niobium foundry service from Hypres. The circuit was stabilized using a low-frequency PLL with a bandwidth of 6 Hz. The output of the phase detector in the PLL was used to produce a feedback current that stabilized the frequency of the ring oscillator at around 8 GHz. The frequency spectrum of the RSFQ scaled oscillator output was measured in open- and closed-loop configurations. Compared to the open-loop phase noise spectrum the closed-loop spectrum showed a decrease of 30 dB of the oscillator phase noise at an offset of 1 Hz from the divided-down carrier frequency of 4.1 kHz. This agreed with the classical phase-locked loop model for the system. The long-term frequency drift of the RSFQ clock was determined by the stability of the oven-controlled quartz oscillator used as the reference in the PLL.

Superconductor Science and Technology•Nov 1, 1999•3 citations

High Quality On-Chip Long Annular Josephson Junction Clock Source for Digital Superconducting Electronics

Dmitri E. Kirichenko, I. V. Vernik

We have developed clock sources for rapid single flux quantum (RSFQ) digital circuits using high-quality long Josephson junction (LJJ) resonant oscillators of annular geometry. Being a topologically closed system and unperturbed by reflections from boundaries and collisions among the fluxons (flux quanta), the annular LJJ oscillator has demonstrated a high quality factor. The novel design of an annular junction clock that allows easier interface with RSFQ circuitry has been realized. Magnetic fluxons are inserted into an annular LJJ by local injection of current into the control line of the junction. This technique resolves the long-standing problem of achieving superior stability of the fluxon state for application as a clock source. The linewidth of the phase-locked clock source is measured as low as 24 Hz relative to a reference oscillator at 40 GHz. The cycle-to-cycle jitter was measured to be 9 fs at a frequency of 36 GHz, or 0.04% of the clock period which is in good agreement with theoretical estimation.

IEEE Transactions on Applied Superconductivity•Jun 1, 2005•14 citations

Linewidth measurements and phase locking of Josephson oscillators using RSFQ circuits

Noshir Dubash, Yongming Zhang, Uttam Ghoshal +1 more

We present a technique for linewidth measurement and phase-locking of Josephson oscillators using digital rapid single-flux-quantum (RSFQ) circuits. The oscillator consists of a resistively shunted 6 /spl mu/m/spl times/6 /spl mu/m Nb/AlO/sub x//Nb Josephson tunnel junction that is integrated with RSFQ input and output circuits. A cascade of RSFQ T flip-flops is used to directly monitor the output of the Josephson oscillator. Spectral characteristics have been measured directly for oscillator frequencies ranging from 10-50 GHz. The linewidth can be reduced by over 100 times by phase-locking the oscillator to an RSFQ pulse train generated by an external sinusoidal signal. These Josephson oscillators can be used as on-chip stable high frequency clocks for RSFQ circuits.

IEEE Transactions on Applied Superconductivity•Jan 1, 1997•4 citations

Two-phase 50 GHz on-chip long Josephson junction clock source

I. V. Vernik, Deepnarayan Gupta

On-chip, high-frequency clock sources are essential for the future development of superconductor digital circuits and systems. We have developed clock sources for rapid single flux quantum (RSFQ) digital circuits using high-quality long Josephson junction (LJJ) resonant oscillators that offer extremely low jitter. To meet the requirement for time-interleaved clock signals of complementary phase, two-phase 30 and 50 GHz clock sources using LJJ's have been developed with both linear and annular geometry. Unperturbed by reflections from boundaries and collisions among the fluxons (flux quanta), the annular LJJ oscillator has demonstrated superior stability and higher quality factor (>10/sup 6/) than the linear LJJ oscillator. The LJJ oscillator with linear geometry is easier to interface with RSFQ circuitry since it has well-defined boundaries at either end, facilitating a two-phase clock source. On the other hand, multiple clock phases may be derived from an annular LJJ oscillator by connecting interface circuitry at various points around the circular junction, if the interface circuitry does not interfere with the fluxon(s) in the annular junction. Experimental results for two-phase RSFQ clock sources based on linear and annular LJJ oscillators are presented.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•11 citations
Stability of Josephson junction clock sources can be a limiting factor in the operation of RSFQ digital and mixed signal circuits. We have developed techniques for the characterization of the short-term stability, i.e., the jitter, of Josephson junction clock sources, and in this paper we present measurements of the jitter for a long Josephson junction soliton oscillator clock. The output frequency of the soliton oscillator was prescaled by using a chain of T flip-flops and using a current bias feedback the oscillator was phase locked to a stable room temperature RP source. Phase noise spectra of the clock signal were measured at the successive stages of the T flip-flop chain and interpreted to infer the cycle-to-cycle jitter of the soliton oscillator. The jitter at the output of the soliton oscillator was measured to be 60 fs at a frequency of 26 GHz, or 0.16% of the period of the clock.
Superconducting digital systems based on Josephson junctions have generally used a synchronous timing strategy. A master clock signal is used to delimit a data window during which the system changes state and data is transferred from one block to the next. The temporal stability of the clock signal has a profound effect on the performance of rapid single flux quantum (RSFQ) digital systems. In particular, short-term clock fluctuations, or clock jitter, can degrade system performance due to the hazard of timing constraint violations. The successful development of large-scale RSFQ digital systems will require highly stable multigigahertz on-chip clock sources. To meet this need, methods for characterizing and measuring the short-term stability of such sources are required. We identify the relevant figure of merit to characterize and compare various clocks: the cycle-to-cycle standard deviation of the clock periods. We present experimental techniques for the measurement of this figure of merit and apply them to the measurement of jitter in a clock generator used often in RSFQ systems, the ring oscillator. High-frequency phase noise measurements found the jitter of a 9.6-GHz clock to be in the range from 0.6% to 0.36% of the clock period. The measured values of clock jitter fell within the 95% confidence interval of our stochastic circuit simulations. This was sufficient evidence to conclude that thermal noise from the resistors in the circuit may be the dominant source of jitter in the ring oscillator.
The temporal stability of the clock signal has a profound effect on the performance of synchronous RSFQ digital systems. Short-term clock fluctuations, or clock jitter, can severely degrade system performance due to the hazard of timing constraint violations. Successful large-scale RSFQ digital systems will require highly stable multi-Gigahertz on-chip clock sources. To meet this need, methods for characterizing and measuring the short-term stability of such sources are required. In this paper we identify the relevant figure of merit to characterize and compare various clocks: the cycle-to-cycle standard deviation of the clock periods. We have developed experimental techniques for the measurement of this figure of merit and applied it to the characterization of an RSFQ ring oscillator. The experimental results are compared with results from a stochastic circuit simulator. We determined the value of jitter to be 1.52% at 10 GHz.
Ring oscillators are the traditional on-chip clock source for RSFQ mixed-signal and digital circuits. Their long-term frequency stability is essential for certain signal processing applications such as the sampling clock for an A/D converter or the output clock of a D/A converter. However conventional bias schemes lead to excessive drift in the frequency. Embedding the ring oscillator in a phase-locked loop (PLL) circuit allows it to inherit the frequency stability of an external reference source. An RSFQ circuit comprised of a ring oscillator, a divide-by-2 20 prescaler and a resynchronizer D flip-flop was fabricated using the standard 1 kA cm -2 niobium foundry service from Hypres. The circuit was stabilized using a low-frequency PLL with a bandwidth of 6 Hz. The output of the phase detector in the PLL was used to produce a feedback current that stabilized the frequency of the ring oscillator at around 8 GHz. The frequency spectrum of the RSFQ scaled oscillator output was measured in open- and closed-loop configurations. Compared to the open-loop phase noise spectrum the closed-loop spectrum showed a decrease of 30 dB of the oscillator phase noise at an offset of 1 Hz from the divided-down carrier frequency of 4.1 kHz. This agreed with the classical phase-locked loop model for the system. The long-term frequency drift of the RSFQ clock was determined by the stability of the oven-controlled quartz oscillator used as the reference in the PLL.
We have developed clock sources for rapid single flux quantum (RSFQ) digital circuits using high-quality long Josephson junction (LJJ) resonant oscillators of annular geometry. Being a topologically closed system and unperturbed by reflections from boundaries and collisions among the fluxons (flux quanta), the annular LJJ oscillator has demonstrated a high quality factor. The novel design of an annular junction clock that allows easier interface with RSFQ circuitry has been realized. Magnetic fluxons are inserted into an annular LJJ by local injection of current into the control line of the junction. This technique resolves the long-standing problem of achieving superior stability of the fluxon state for application as a clock source. The linewidth of the phase-locked clock source is measured as low as 24 Hz relative to a reference oscillator at 40 GHz. The cycle-to-cycle jitter was measured to be 9 fs at a frequency of 36 GHz, or 0.04% of the clock period which is in good agreement with theoretical estimation.
We present a technique for linewidth measurement and phase-locking of Josephson oscillators using digital rapid single-flux-quantum (RSFQ) circuits. The oscillator consists of a resistively shunted 6 /spl mu/m/spl times/6 /spl mu/m Nb/AlO/sub x//Nb Josephson tunnel junction that is integrated with RSFQ input and output circuits. A cascade of RSFQ T flip-flops is used to directly monitor the output of the Josephson oscillator. Spectral characteristics have been measured directly for oscillator frequencies ranging from 10-50 GHz. The linewidth can be reduced by over 100 times by phase-locking the oscillator to an RSFQ pulse train generated by an external sinusoidal signal. These Josephson oscillators can be used as on-chip stable high frequency clocks for RSFQ circuits.
On-chip, high-frequency clock sources are essential for the future development of superconductor digital circuits and systems. We have developed clock sources for rapid single flux quantum (RSFQ) digital circuits using high-quality long Josephson junction (LJJ) resonant oscillators that offer extremely low jitter. To meet the requirement for time-interleaved clock signals of complementary phase, two-phase 30 and 50 GHz clock sources using LJJ's have been developed with both linear and annular geometry. Unperturbed by reflections from boundaries and collisions among the fluxons (flux quanta), the annular LJJ oscillator has demonstrated superior stability and higher quality factor (>10/sup 6/) than the linear LJJ oscillator. The LJJ oscillator with linear geometry is easier to interface with RSFQ circuitry since it has well-defined boundaries at either end, facilitating a two-phase clock source. On the other hand, multiple clock phases may be derived from an annular LJJ oscillator by connecting interface circuitry at various points around the circular junction, if the interface circuitry does not interfere with the fluxon(s) in the annular junction. Experimental results for two-phase RSFQ clock sources based on linear and annular LJJ oscillators are presented.