Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

A Single Flux Quantum cross-bar switch and demultiplexer

A. Hodge Worsham, John X. Przybysz, Joonhee Kang, Donald L. Miller

Published Jun 1, 1995• 19 citations
Publisher

Abstract

A Single Flux Quantum (SFQ) demultiplexer and a cross-bar switch for a high speed data switch are described. Both circuits were error-free in simulation to 15 Gbps. The cross-bar switch was two input, two output (2/spl times/2) and used /spl sim/400 /spl mu/A control signals to set the data path. The switch has been demonstrated at over 15 Gbps/line using average voltage measurements. The correct routing of a bit stream was demonstrated at 2.488 Gbps.>

DOI
10.1109/77.403222

Related papers

Single flux quantum circuits for 2.5 Gbps data switching

A. Hodge Worsham, A. H. Miklich, Donald L. Miller +2 more

We have designed and measured single flux quantum (SFQ) circuits for data switching at 2.5 Gbps. A fully functional 2/spl times/2 switching node is presented. The node can be used to form a larger switching fabric (4/spl times/4, 8/spl times/8, etc.). The node accepts data streams at either or both inputs, routing the data based on address bits present in the data stream. This approach allows the data to be self-routing and the switch to be self-synchronous. In addition, the switch can route data correctly on an active input line if the other is idle.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•15 citations

High-Speed Demonstration of Single-Flux-Quantum Cross–Bar Switch up to 50 GHz

Y. Kameda, Shinichi Yorozu, Y. Hashimoto +3 more

We have been developing a single-flux-quantum (SFQ) cross-bar switch, which is a main component of a network packet switch. We think that a network switch is an application in which the high speed of SFQ technology would be advantageous. Anticipating general and large-scale SFQ logic circuit design, we used the cell-based design method and the CONNECT standard SFQ cell library. The two-input and two-output cross-bar switch, a core switch component, consists of 13 logic cells connected by Josephson-transmission-line (JTL) cells. Because of the large size of JTL cells and the large delay in them, timing adjustment becomes more difficult as the operating speed and circuit size increase. After using a commercially available automatic router to find appropriate routes efficiently, we used a static timing analyzer for fine timing adjustment. Timing violations were fixed by changing JTL path delays using the tools we developed. The target operating frequency of the switch was 40 GHz, which corresponds to a clock period of 25 ps. Careful timing adjustment was necessary to ensure correct operations at such a high speed. The test chip was fabricated by using an NEC standard Nb process. The circuit, including on-chip test circuitry, was composed of about 1500 Josephson junctions. We confirmed its correct operations up to 50 GHz with a bias margin of /spl plusmn/20%.

IEEE Transactions on Applied Superconductivity•Mar 1, 2005•15 citations

Quantitative Evaluation of the Single-Flux- Quantum Cross/Bar Switch

Takahiro Yamada, Masato Yoshida, T. Hanai +6 more

We demonstrated the 4 /spl times/ 4-cross/bar-40 Gbps/ch switch which is functionally compatible with a commercial semiconductor one in order to evaluate the current SFQ circuit technology quantitatively in both a operating speed and power consumption. According to our numerical simulations, the SFQ switch has one or two orders of magnitude higher throughput per a single channel than that of the semiconductor, and has much smaller exchanging times between routing paths. In an actual test based on the NEC Nb-2.5 kA/cm/sup 2/ junction technology, correct operation using an on-chip test system made up of 4700 Josephson junctions was confirmed up to 37 Gbps/ch which is about 14 times faster than the semiconductor of 2.7 Gbps/ch speed. We also confirmed that SFQ circuits consumed 1/800 power compared with those of semiconductor. The reason why data rates obtained experimentally did not reach the designed speed of 40 Gbps/ch is due to both the timing error and the influence of magnetic fields caused by large bias currents exceeding 500 mA. These results of quantitative evaluation show that the SFQ technology has much greater potentials than the semiconductor one in both the operating speed and the power consumption, which means it is very effective to apply the SFQ technology to digital applications.

IEEE Transactions on Applied Superconductivity•Jun 1, 2005•11 citations

4-bit rapid single-flux-quantum decoder

Alex F. Kirichenko, Vasili K. Semenov, Ying Ki Kwong +1 more

We describe the design of a fast single-flux-quantum decoder which can be used, e.g., in fast RAMs, general-purpose microprocessors, and communication channel switches. The core of the circuit is a tree of the single-bit SFQ demultiplexer with toggle (rather than the reset-set) control. Three new RSFQ cells: the demultiplexer, D flip-flop with complementary outputs, and serial XOR with large parameter tolerances (dc bias margins of /spl plusmn/25%, /spl plusmn/26%, and /spl plusmn/27%, respectively) have been developed for the decoder project. We have designed the first 16-bit prototype of the decoder for 1-kA/cm/sup 2/ niobium-trilayer technology and tested it at low frequencies. The circuit was completely operable except for 3 (of 16) output SFQ/DC converters. Simulations show that the circuit should allow data rate in excess of 60 Gbit/s and channel switching time below 20 ps.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•28 citations

High-Speed Operation of a Single-Flux-Quantum (SFQ) Cross/Bar Switch up to 35 GHz

義男 亀田, Shinichi Yorozu, Hirotaka Terai +1 more

Single-flux-quantum (SFQ) technology is a novel technology where binary information is represented by a single flux. It enables us to realize high-speed, low-power SFQ logic circuits, surpassing conventional complementary metal-oxide-silicon (CMOS) technology. We proposed an SFQ packet switch to avoid the bottlenecks in broadband networks of the future. To demonstrate high-speed operation of an SFQ logic circuit and its application to our switch architecture, we designed a cross/bar switch. It consists of 13 logic gates and 581 Josephson junctions were used in the layout. We confirmed correct operations up to 33 GHz in simulation. We placed the switch circuit in an on-chip test system for high-speed (over 10 GHz) test. Including I/O circuits, the system as a whole consists of 1236 Josephson junctions. The chip was fabricated by using NEC's standard Nb process. We carried out an on-chip test and found correct operations up to 35 GHz.

Japanese Journal of Applied Physics•Apr 30, 2003•8 citations

Single flux quantum crossbar switch

Qing Ke, Bruce J. Dalrymple, D.J. Durand +1 more

A crossbar switch has been designed using Single Flux Quantum (SFQ) gates exclusively for all internal functions. A 4/spl times/4 prototype has been fabricated in our Nb process foundry with J/sub c/ of 2000 A/cm/sup 2/. We report on the design and performance of the switch and of an individual crosspoint element at high data rates (/spl ges/1 Gbps). A novel design of a double-edge-triggered dc/SFQ converter is discussed. The requirements for output amplification and on-chip versus off-chip amplifier issues will be presented.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•13 citations
A Single Flux Quantum (SFQ) demultiplexer and a cross-bar switch for a high speed data switch are described. Both circuits were error-free in simulation to 15 Gbps. The cross-bar switch was two input, two output (2/spl times/2) and used /spl sim/400 /spl mu/A control signals to set the data path. The switch has been demonstrated at over 15 Gbps/line using average voltage measurements. The correct routing of a bit stream was demonstrated at 2.488 Gbps.>
We have designed and measured single flux quantum (SFQ) circuits for data switching at 2.5 Gbps. A fully functional 2/spl times/2 switching node is presented. The node can be used to form a larger switching fabric (4/spl times/4, 8/spl times/8, etc.). The node accepts data streams at either or both inputs, routing the data based on address bits present in the data stream. This approach allows the data to be self-routing and the switch to be self-synchronous. In addition, the switch can route data correctly on an active input line if the other is idle.
We have been developing a single-flux-quantum (SFQ) cross-bar switch, which is a main component of a network packet switch. We think that a network switch is an application in which the high speed of SFQ technology would be advantageous. Anticipating general and large-scale SFQ logic circuit design, we used the cell-based design method and the CONNECT standard SFQ cell library. The two-input and two-output cross-bar switch, a core switch component, consists of 13 logic cells connected by Josephson-transmission-line (JTL) cells. Because of the large size of JTL cells and the large delay in them, timing adjustment becomes more difficult as the operating speed and circuit size increase. After using a commercially available automatic router to find appropriate routes efficiently, we used a static timing analyzer for fine timing adjustment. Timing violations were fixed by changing JTL path delays using the tools we developed. The target operating frequency of the switch was 40 GHz, which corresponds to a clock period of 25 ps. Careful timing adjustment was necessary to ensure correct operations at such a high speed. The test chip was fabricated by using an NEC standard Nb process. The circuit, including on-chip test circuitry, was composed of about 1500 Josephson junctions. We confirmed its correct operations up to 50 GHz with a bias margin of /spl plusmn/20%.
We demonstrated the 4 /spl times/ 4-cross/bar-40 Gbps/ch switch which is functionally compatible with a commercial semiconductor one in order to evaluate the current SFQ circuit technology quantitatively in both a operating speed and power consumption. According to our numerical simulations, the SFQ switch has one or two orders of magnitude higher throughput per a single channel than that of the semiconductor, and has much smaller exchanging times between routing paths. In an actual test based on the NEC Nb-2.5 kA/cm/sup 2/ junction technology, correct operation using an on-chip test system made up of 4700 Josephson junctions was confirmed up to 37 Gbps/ch which is about 14 times faster than the semiconductor of 2.7 Gbps/ch speed. We also confirmed that SFQ circuits consumed 1/800 power compared with those of semiconductor. The reason why data rates obtained experimentally did not reach the designed speed of 40 Gbps/ch is due to both the timing error and the influence of magnetic fields caused by large bias currents exceeding 500 mA. These results of quantitative evaluation show that the SFQ technology has much greater potentials than the semiconductor one in both the operating speed and the power consumption, which means it is very effective to apply the SFQ technology to digital applications.
We describe the design of a fast single-flux-quantum decoder which can be used, e.g., in fast RAMs, general-purpose microprocessors, and communication channel switches. The core of the circuit is a tree of the single-bit SFQ demultiplexer with toggle (rather than the reset-set) control. Three new RSFQ cells: the demultiplexer, D flip-flop with complementary outputs, and serial XOR with large parameter tolerances (dc bias margins of /spl plusmn/25%, /spl plusmn/26%, and /spl plusmn/27%, respectively) have been developed for the decoder project. We have designed the first 16-bit prototype of the decoder for 1-kA/cm/sup 2/ niobium-trilayer technology and tested it at low frequencies. The circuit was completely operable except for 3 (of 16) output SFQ/DC converters. Simulations show that the circuit should allow data rate in excess of 60 Gbit/s and channel switching time below 20 ps.>
Single-flux-quantum (SFQ) technology is a novel technology where binary information is represented by a single flux. It enables us to realize high-speed, low-power SFQ logic circuits, surpassing conventional complementary metal-oxide-silicon (CMOS) technology. We proposed an SFQ packet switch to avoid the bottlenecks in broadband networks of the future. To demonstrate high-speed operation of an SFQ logic circuit and its application to our switch architecture, we designed a cross/bar switch. It consists of 13 logic gates and 581 Josephson junctions were used in the layout. We confirmed correct operations up to 33 GHz in simulation. We placed the switch circuit in an on-chip test system for high-speed (over 10 GHz) test. Including I/O circuits, the system as a whole consists of 1236 Josephson junctions. The chip was fabricated by using NEC's standard Nb process. We carried out an on-chip test and found correct operations up to 35 GHz.
A crossbar switch has been designed using Single Flux Quantum (SFQ) gates exclusively for all internal functions. A 4/spl times/4 prototype has been fabricated in our Nb process foundry with J/sub c/ of 2000 A/cm/sup 2/. We report on the design and performance of the switch and of an individual crosspoint element at high data rates (/spl ges/1 Gbps). A novel design of a double-edge-triggered dc/SFQ converter is discussed. The requirements for output amplification and on-chip versus off-chip amplifier issues will be presented.