Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

RSFQ-based D/A converter for AC voltage standard

Hajime SASAKI, Shogo Kiryu, Fuminori Hirayama, Tsuneo Kikuchi, Masaaki Maezawa, Alexandre Shoji, Stanislav V. Polonsky

Published Jun 1, 1999• 46 citations
Publisher

Abstract

Digital to analog converters based on the Josephson effect are promising for voltage standards, because they produce voltage steps with ultimate precision and stability. In this paper, we describe a project to develop a Josephson D/A converter designed for synthesizing a sinusoidal waveform with metrological accuracy. The D/A converter is based on RSFQ (Rapid Single Flux Quantum) logic circuits, and consists of a frequency multiplier (FM), a pulse distributor (PD), and a number of voltage multipliers (VMs). Each VM circuit, corresponding to the n-th bit digital code, multiplies the number of SFQ pulses by a factor of 2/sup n/. By gating the input SFQ pulses from the FM to the VMs using the PD circuits, a programmable output voltage is obtained. Possible sources of uncertainties in the measurement of the rms value of the synthesized sine wave are discussed.

DOI
10.1109/77.783799

Related papers

Characteristics of a voltage multiplier for a RSFQ digital-to-analog converter

Fuminori Hirayama, Masaaki Maezawa, Shogo Kiryu +2 more

We are developing a digital-to-analog (D/A) converter based on rapid single flux quantum (RSFQ) logic circuits. Since the RSFQ D/A converter operates according to the Josephson frequency–voltage relationship, arbitrary waveforms can be synthesized with an accuracy equivalent to that of the Josephson dc voltage standard. We have examined the characteristics of magnetically coupled voltage multipliers (VMs). The VM is a key component in the RSFQ D/A converter for use in metrological applications.

Superconductor Science and Technology•Feb 19, 2002•7 citations

Voltage Doubler Cell for Rapid Single Flux Quantum Digital-to-Analog Converter

Yoko Namatame, Masaaki Maezawa, Masataka Moriya +3 more

Digital-to-analog converters based on rapid single flux quantum circuits (RSFQ-D/A converters) are candidates for the next generation of ac voltage standard. We re-optimized the device parameters of a voltage multiplier (VM) cell, one of the important components in the RSFQ-D/A converter, to implement a new voltage doubler (VD) cell. The output voltage of the VD cell was twice as high as that of the conventional VM cell. We fabricated VD cells using a Nb technology. We confirmed correct operation of the VD cells at input frequencies up to 30 GHz.

Japanese Journal of Applied Physics•Apr 27, 2007•3 citations

Design and Operation of 1000-fold Voltage Multiplier based on Double-flux-quantum Amplifier

Yusuke Sato, Masataka Moriya, Hiroshi Shimada +2 more

Rapid-single-flux-quantum digital-to-analogue converters (RSFQ-DACs) are now under development for ac voltage standard applications. The voltage multiplier (VM), which precisely amplifies the input voltage, is a key component for RSFQ-DACs. Because the amount of bias current for a conventional VM increases in proportion to its multiplication factor, we have been looking for a VM device which is operated on a different principle. In this paper, we report our design of a 1000-fold VM comprising double flux quantum amplifiers (DFQAs) of which the amount of bias current is independent of its multiplication factor. Test circuits were fabricated using a 2.5 kA/cm2 Nb process. We confirm that the experimental results demonstrate the 1000-fold operation up to 13.2 GHz input SFQ pulse repetition frequency.

Physics Procedia•Jan 1, 2013•14 citations

Superconducting bipolar digital-to-analog converter equipped with dual double-flux-quantum amplifier

Yoshinao Mizugaki, Tomoki Watanabe, Hiroshi Shimada

Precise voltage generation is a unique feature of superconducting single-flux-quantum (SFQ) circuits, and hence, several SFQ-based digital-to-analog converters (DACs) have been designed for metrological applications. In this letter, we propose a dual double-flux-quantum amplifier (dual-DFQA) that extends DAC output voltage from unipolar to bipolar. An SFQ-based DAC comprising a 4-bit variable pulse number multiplier and a ±20-fold dual-DFQA is fabricated using a niobium integration technology. A 1-kHz, ±0.29-mV sinusoidal voltage waveform is successfully synthesized.

IEICE Electronics Express•Jan 1, 2016•5 citations

Analog-to-digital conversion for low-frequency waveforms based on the Josephson voltage standard

Mun-Seog Kim, Kyu‐Tae Kim, Wan-Seop Kim +2 more

A waveform synthesizer adopting a superconductor–normal metal–superconductor junction array has been developed, which can generate arbitrary stepwise waveforms with a number of quantum-voltage steps up to 1 V level amplitude. As an application of the synthesizer, we have built a sampling voltmeter that measures the differential voltages between a sinusoidal waveform produced by a semiconductor-based ac source and the Josephson waveforms. We carried out extensive sampling measurements for a 50 Hz sine wave with 1 V amplitude, applying sampling apertures in the range of 55 µs ⩽ t a ⩽ 130 µs and using Josephson waveforms with 32, 60, 80 and 100 quantum steps. From the measurements, the amplitude of the ac waveform was determined with a type A uncertainty ( k = 2) of 0.15 µV. Also, we elucidated how the phase jitter in the ac waveform is reflected in the overall uncertainty for the measurements. The type B uncertainty due to the jitter is at least one order of magnitude smaller than the type A uncertainty.

Measurement Science and Technology•Sep 24, 2010•38 citations

Superconductor digital-to-analog converter based on processing of SFQ pulses

Vasili K. Semenov, P.N. Shevchenko, Yu. A. Polyakov

Recently we designed and successfully tested a prototype of a superconducting digital-to-analog converter (DAC) based on processing single flux quantum (SFQ) pulses. Two unique features make the device very attractive for metrology applications: (i) The generation of output voltage is based on the fundamentally accurate Josephson frequency-to-voltage relationship. (ii) The device does not require any external signals with frequencies higher than 100 MHz. It is expected that the DAC will be used as a key component of novel standards and calibrators of ac voltage with frequency up to 1 MHz. The implemented prototype has low magnitude of output voltage (about 10 mV) which is far lower than the 1 to 10 V target magnitude.

Conference on Precision Electromagnetic Measurements•Nov 27, 2002•9 citations
Digital to analog converters based on the Josephson effect are promising for voltage standards, because they produce voltage steps with ultimate precision and stability. In this paper, we describe a project to develop a Josephson D/A converter designed for synthesizing a sinusoidal waveform with metrological accuracy. The D/A converter is based on RSFQ (Rapid Single Flux Quantum) logic circuits, and consists of a frequency multiplier (FM), a pulse distributor (PD), and a number of voltage multipliers (VMs). Each VM circuit, corresponding to the n-th bit digital code, multiplies the number of SFQ pulses by a factor of 2/sup n/. By gating the input SFQ pulses from the FM to the VMs using the PD circuits, a programmable output voltage is obtained. Possible sources of uncertainties in the measurement of the rms value of the synthesized sine wave are discussed.
We are developing a digital-to-analog (D/A) converter based on rapid single flux quantum (RSFQ) logic circuits. Since the RSFQ D/A converter operates according to the Josephson frequency–voltage relationship, arbitrary waveforms can be synthesized with an accuracy equivalent to that of the Josephson dc voltage standard. We have examined the characteristics of magnetically coupled voltage multipliers (VMs). The VM is a key component in the RSFQ D/A converter for use in metrological applications.
Digital-to-analog converters based on rapid single flux quantum circuits (RSFQ-D/A converters) are candidates for the next generation of ac voltage standard. We re-optimized the device parameters of a voltage multiplier (VM) cell, one of the important components in the RSFQ-D/A converter, to implement a new voltage doubler (VD) cell. The output voltage of the VD cell was twice as high as that of the conventional VM cell. We fabricated VD cells using a Nb technology. We confirmed correct operation of the VD cells at input frequencies up to 30 GHz.
Rapid-single-flux-quantum digital-to-analogue converters (RSFQ-DACs) are now under development for ac voltage standard applications. The voltage multiplier (VM), which precisely amplifies the input voltage, is a key component for RSFQ-DACs. Because the amount of bias current for a conventional VM increases in proportion to its multiplication factor, we have been looking for a VM device which is operated on a different principle. In this paper, we report our design of a 1000-fold VM comprising double flux quantum amplifiers (DFQAs) of which the amount of bias current is independent of its multiplication factor. Test circuits were fabricated using a 2.5 kA/cm2 Nb process. We confirm that the experimental results demonstrate the 1000-fold operation up to 13.2 GHz input SFQ pulse repetition frequency.
Precise voltage generation is a unique feature of superconducting single-flux-quantum (SFQ) circuits, and hence, several SFQ-based digital-to-analog converters (DACs) have been designed for metrological applications. In this letter, we propose a dual double-flux-quantum amplifier (dual-DFQA) that extends DAC output voltage from unipolar to bipolar. An SFQ-based DAC comprising a 4-bit variable pulse number multiplier and a ±20-fold dual-DFQA is fabricated using a niobium integration technology. A 1-kHz, ±0.29-mV sinusoidal voltage waveform is successfully synthesized.
A waveform synthesizer adopting a superconductor–normal metal–superconductor junction array has been developed, which can generate arbitrary stepwise waveforms with a number of quantum-voltage steps up to 1 V level amplitude. As an application of the synthesizer, we have built a sampling voltmeter that measures the differential voltages between a sinusoidal waveform produced by a semiconductor-based ac source and the Josephson waveforms. We carried out extensive sampling measurements for a 50 Hz sine wave with 1 V amplitude, applying sampling apertures in the range of 55 µs ⩽ t a ⩽ 130 µs and using Josephson waveforms with 32, 60, 80 and 100 quantum steps. From the measurements, the amplitude of the ac waveform was determined with a type A uncertainty ( k = 2) of 0.15 µV. Also, we elucidated how the phase jitter in the ac waveform is reflected in the overall uncertainty for the measurements. The type B uncertainty due to the jitter is at least one order of magnitude smaller than the type A uncertainty.
Recently we designed and successfully tested a prototype of a superconducting digital-to-analog converter (DAC) based on processing single flux quantum (SFQ) pulses. Two unique features make the device very attractive for metrology applications: (i) The generation of output voltage is based on the fundamentally accurate Josephson frequency-to-voltage relationship. (ii) The device does not require any external signals with frequencies higher than 100 MHz. It is expected that the DAC will be used as a key component of novel standards and calibrators of ac voltage with frequency up to 1 MHz. The implemented prototype has low magnitude of output voltage (about 10 mV) which is far lower than the 1 to 10 V target magnitude.