IEEE Transactions on Applied Superconductivity

High-Temperature Operation of Oxide SFQ-Circuit-Elements

Koji Tsubone, H. Wakana, Yoshihiro Ishimaru, Seiji Adachi, Ken‐ichi Nakayama, Y. Tarutani, K. Tanabe

Published Dec 1, 2005• 16 citations

Abstract

Single flux quantum (SFQ) circuit components such as an SFQ-dc converter and a confluence buffer have been fabricated by using an YBa/sub 2/Cu/sub 3/O/sub 7-/spl delta// ramp-edge junction technology and their logic operations at temperatures up to near 60 K were investigated. The SFQ-dc converter was correctly operated in a wide temperature range from 4.2 K to 56 K and found to be useful for detecting output signals from other SFQ circuit components at any operating temperatures. The basic function that a signal from either of two input Josephson transmission lines (JTLs) was transmitted to an output JTL was confirmed for the confluence buffer and finite operating margins were obtained at temperatures from 42 K to 61 K. The narrowest margin of dc supply current obtained at temperatures from 55 K to 60 K was /spl plusmn/20% and was consistent with the simulation. Margin reduction due to thermal noise was also evaluated. According to the analytical calculation, the operating margin to keep the bit-error rate less than 10/sup -5/ was as large as /spl plusmn/20% even at 50 K when the value of junction critical-current I/sub c/ was kept near 0.4 mA.

DOI: 10.1109/tasc.2005.859045

Related papers

Fabrication and Logic Operation of Oxide SFQ-Circuit-Components

Y. Tarutani, Yoshihiro Ishimaru, H. Wakana +6 more

Basic SFQ circuit components, such as SFQ-dc converter, set-reset flip-flop (RS-FF), confluence buffer and splitter, have been fabricated by the YBa/sub 2/Cu/sub 3/O/sub 7-x/-ramp-edge-junction technology and their logic operations were investigated. Circuit parameters were optimized in order to widen the margins of these oxide SFQ circuit components. The SFQ-dc converter that comprised double SQUIDs connected in series showed the output voltage as much as 0.3 mV at 22 K owing to high I/sub c/R/sub n/ value of the ramp-edge junction. Logic operations of the RS-FF, the confluence buffer and the splitter were correctly performed by using the SFQ-dc converter. Finite operating margins were obtainable for these circuits up to the temperature near 30 K.

IEEE Transactions on Applied SuperconductivityJun 1, 200521 citations

Design and Operation of HTS SFQ Circuit Elements

Koji Tsubone, H. Wakana, Y. Tarutani +3 more

Single flux quantum (SFQ) circuit elements have been designed and fabricated using the YBa 2 Cu 3 O 7-δ ramp-edge junction technology. Logic operations of SFQ circuit elements, such as a toggle flip-flop (T-FF), a set-reset flip-flop (RS-FF), and a 96-junction Josephson transmission line (JTL), were successfully demonstrated, and dc supply current margins were confirmed up to temperatures higher than 30 K. The circuit layout was improved in order to suppress the critical current (I c ) spread that appears during the junction fabrication procedure. By employing the new circuit layout rule, correct operations at temperatures from 27 K to 34 K with dc supply current margins wider than ±7% were confirmed for the T-FF with a single output. Moreover, the maximum operating frequencies of T-FFs were measured to be 360GHz at 4.2K and 210GHz at 41K, which are substantially higher than the values for the circuits with the conventional layout. According to the simulation result, the maximum operating frequency at 40 K was expected to be approximately 50% of the characteristic frequency at a bit error rate (BER) less than 10 -6 .

IEICE Transactions on ElectronicsMar 1, 20074 citations

Logic Operation of SFQ Circuit Elements Made of YBCO Junctions

Y. Tarutani, Koji Tsubone, H. Wakana +6 more

YBa2Cu3O7-x(YBCO) ramp-edge junction technologies have been developed for fabricating high-operating-temperature SFQ(Single Flux Quantum) circuits. The Ic(critical current) spread that is the key parameter for integrating junctions could be decreased to 8% for a 1000-junction array that was formed on a groundplane. The background technologies that enabled this uniform junction characteristic are precise control of the counter-electrode deposition-conditions and deposition of the extremely smooth multiplayer that showed the roughness as small as 2 nm. Based upon these ramp-edge junction technologies, oxide SFQ-circuit-elements were fabricated and their logic operations were investigated. SFQ circuit elements such as a confluence buffer, a set-reset flipflop, and a toggle flipflop have been fabricated and their logic operations were measured by using an SFQ-dc converter. Both toggle flipflops that have one output and two outputs have been fabricated. These circuits could be operated up to the temperature of near 60 K under finite operating margins. These experimental results enable us to further develop fuctional and much more integrated SFQ circuits.

Advances in science and technologyOct 1, 20061 citation

SFQ-to-level logic conversion by HTS Josephson drivers for output interface

Tsunehiro Hato, Yoshihiro Ishimaru, N. Harada +5 more

Latching-type driver circuits integrated with high-temperature superconductivity (HTS) junctions and two types of resistor were fabricated. These circuits could successfully perform latching operation by means of a single-flux-quantum (SFQ) signal input. Ramp-edge-type HTS junctions were fabricated by interface engineering and showed a hysteretic current-voltage characteristics under a temperature of 50 K. The critical current (I/sub c/) of these 5-micron-wide junctions was about 0.2 mA and the I/sub c/R/sub n/ product was about 1.7 mV at 4.2 K. The circuits included two types of resistors, which were made of RF-magnetron-sputtered indium-tin-oxide (ITO) and Au films. A driver with a parallel 2-junction-stack could convert an SFQ pulse, which was transformed through several Josephson transmission lines (JTL's) from a DC/SFQ circuit, to a 2.3-mV level signal.

IEEE Transactions on Applied SuperconductivityJun 1, 20038 citations

A high-temperature superconductor latching driver operated at 30 K for a single-flux-quantum/semiconductor interface

Tsunehiro Hato, Masahiro Horibe, Naoki Harada +5 more

We report on a latching-type driver operated at 30 K for the output interface of single-flux-quantum (SFQ) circuits. Ramp-edge-type high-temperature superconductor (HTS) junctions showed only small inherent hysteresis in current–voltage characteristics at a temperature of 30 K. To have hysteresis large enough for latching operation, we chose La-doped YbBaCuO as a counter electrode of an interface modified junction, and used amorphous LaSrAlTaO to form an additional barrier to the interface modified barrier. The junction shunted with optimized capacitance showed sufficiently large hysteresis of 33%, which is as large as that of a non-shunted junction at 4.2 K. We employed 20 kA cm−2 as the critical current density (Jc) of the junction to fabricate dc/SFQ, Josephson transmission lines (JTLs) and the latching driver on the same chip. It is smaller than the optimum current density that gives the smallest punchthrough probability of the junction, which was calculated to be 10−12 for a 30 Gbps ac bias by using the junction parameters at 30 K. However, the probability for Jc of 20 kA cm−2 is still smaller than that of low-temperature semiconductor junctions because of the larger Jc of the HTS junctions. The fabricated latching driver successfully converted the SFQ pulse, which passed through several JTLs from the dc/SFQ circuit, to a 1 mV level signal at 30 K.

Superconductor Science and TechnologyNov 7, 20033 citations

Operation of HTS Toggle-Flip-Flop Circuit With Improved Layout Design

Koji Tsubone, H. Wakana, Yoshinobu Tarutani +4 more

Toggle-flip-flop (T-FF) is one of the most important high-Tcsuperconducting single-flux quantum (HTS SFQ) circuit components and has been designed and fabricated by using YBa2Cu3O7-deltaramp-edge junction technology. The circuit layout of the T-FF was improved to suppress the junction critical current (Ic) spread in the circuit. Test circuits, which include a T-FF with a single output for evaluating the logic operation and measuring the operating frequency, were fabricated and their operation characteristics were investigated. The T-FF circuit with a single output was successfully operated and finite direct current (dc) supply current margins were obtained at temperatures from 27 to 34 K. Moreover, the maximum operating frequency of the T-FF was estimated to be 360 GHz at 4.2 K and 114 GHz at 41 K. In addition, reduction of dc supply current margins due to thermal noise was also investigated. According to the numerical simulation in which parasitic inductances were taken into account, the narrowest margin in the T-FF circuit wider than plusmn10% was maintained with a bit-error rate (BER) of 10-6up to 40 K

IEEE Transactions on Applied SuperconductivityDec 1, 200615 citations