Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

New design of single-bit all-digital RSFQ autocorrelator

Alexander V. Rylyakov

Published Jun 1, 1997• 42 citations
Publisher

Abstract

We present a new design of a Rapid Single-Flux-Quantum (RSFQ) all-digital one-bit autocorrelator for submillimeter spectrometry applications, featuring 4 GHz input signal bandwidth, double oversampling quantizer, and 16 Mbps-per-channel output rate. The delay line of the autocorrelator is based on a circular shift register with XOR gates performing multiplication of the delayed and undelayed single-bit signals at every stage. The multiplication results are accumulated by room-temperature electronics after being prescaled in on-chip binary counters consisting of 10 T flip-flops per stage. We report results of experimental testing of a 16-stage autocorrelator delay line with multiplication and for a linear array of 8 low-power T flip-flop binary counters, all fabricated in HYPRES' standard 3.5 /spl mu/m 1000 A/cm/sup 2/ Nb-trilayer process. We also discuss physical and technical limits of the minimal power dissipation in RSFQ circuits.

DOI
10.1109/77.621797

Related papers

All-digital 1-bit RSFQ autocorrelator for radioastronomy applications: design and experimental results

Alexander V. Rylyakov, Stanislav V. Polonsky

We present the design of a rapid single-flux-quantum all-digital 1-bit autocorrelator for submillimeter spectrometry applications, featuring 4-GHz input signal bandwidth, double oversampling quantizer, and 16-Mb/s-per-channel output rate. The correlator consists of a digital delay line with multiplication and an array of accumulators with parallel readout. We report experimental results for a three-stage delay line (294 Josephson junctions) and a 4/spl times/4 array of accumulators (288 Josephson junctions) fabricated in HYPRES' standard 3.5-/spl mu/m 1000-A/cm/sup 2/ Nb-trilayer process.

IEEE Transactions on Applied Superconductivity•Mar 1, 1998•17 citations

A fully integrated 16-channel RSFQ autocorrelator operating at 11 GHz

Alexander V. Rylyakov, D.F. Schneider, Yu. A. Polyakov

We present the results of low- and high-speed testing of a fully integrated all-digital one-bit RSFQ autocorrelator for short-millimeter and submillimeter wave spectrometry applications. The 16-channel device, complete with a 16/spl times/9 array of binary counters, on-chip double-oversampling quantizer and on-chip clock was operational at clock speeds of up to 11 GHz. The total number of Josephson junctions in the design was 1672, while the estimated total power dissipation was less than 0.1 mW. For high-speed testing of the device we have developed a specialized 16-channel room-temperature interface capable of real-time data acquisition at a 16 Mbps-per-channel output rate. Extensive high-speed on-chip testing of the autocorrelator has also been performed, both in analog and digital modes, in the latter mode with an additional on-chip clock controller. All chips were fabricated in HYPRES' standard 3.5 /spl mu/m-10 /spl mu/A//spl mu/m/sup 2/ Nb-trilayer process. We also present a new concept of a 128-channel autocorrelator system built on 8 independent identical chips with approximately 2,500 Josephson junctions per chip, i.e. within the reach of the present-day fabrication technology.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•15 citations

Single flux quantum digital devices

V. P. Koshelets

A new generation of the Josephson digital circuits-rapid single flux quantum (RSFQ) devices-based on overdamped externally shunted high quality Nb-AlO x -Nb tunnel junctions have been designed, fabricated and experimentally investigated. All-refractory material 11-layer 5 mu m integrated technology has been successfully employed for the preparation of the RSFQ microcircuits. The T flip-flop has been demonstrated to operate properly up to clock frequencies of 100 GHz at 25% margins. The proper operation of the buffer stage for a one-directional SFQ pulse transmission at clock frequencies up to 125 GHz has been achieved. The possibilities to convert the information from the usual DC form to SFQ and vice versa have been demonstrated. An output signal in an SFQ/DC converter as high as 220 mu V has been measured. A new counter type A/D converter which includes a comparator and reversible binary counter with DC outputs has been fabricated and tested. The proposed ADC seems to be very promising for high-accuracy measurement of medium-bandwidth signals. The possibilities of creating a number of SFQ devices with outstanding parameters are discussed.

Superconductor Science and Technology•Nov 1, 1991•5 citations

Design of SFQ-counting analog-to-digital converter

J.C. Lin, Vasili K. Semenov, Konstantin K. Likharev

We describe the design of an oversampling single-flux-counting analog-to-digital converter with the estimated bandwidth of a few tens of MHz, based on Rapid Single-Flux-Quantum (RSFQ) devices. It consists of an input analog circuit, high-speed quantizer with an original analog/digital negative feedback loop, decimation (comb) filter, and supporting subsystems including clock distribution circuits, quantization signal conditioner, and output drivers. We have applied a new approach, the 'symmetrizing' negative feedback, to free the quantizer from the intrinsic hysteresis without dynamic range sacrifice. The 16-bit version of the system comprises about 1,500 Josephson junctions and consumes 1.2 mW of DC power, when implemented using Nb-trilayer technology with 1 kA/cm/sup 2/, 3.5 /spl mu/m Josephson junctions. All subsystems of the converter have been successfully tested and testing of the system as a whole is in progress.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•51 citations

Superconductive single-flux quantum technology

Oleg A. Mukhanov

Key digital circuits for signal processing with tens of gigahertz speed and a few microwatts power dissipation have been recently demonstrated using a simple, 2 /spl mu/m linewidth process. These are the fastest digital circuits reported to date. These circuits use novel rapid single flux quantum (RSFQ) technology that takes advantage of the fundamental properties of superconductivity. In this technology, data and clock are picosecond-long quantized voltage pulses corresponding to the transfer of single magnetic flux quanta, /spl Phisub 0/=h/2e=2 mVps. These SFQ pulses are regenerated at each gate and are processed by circuits comprised of overdamped Josephson junctions interconnected via microstrip inductances. The inherent internal memory of all RSFQ gates (primarily flip-flops), combined with high switching speed, makes serial, bit-pipelined circuit design advantageous. This paper presents experiments in RSFQ digital circuits, including an N/spl times/8b serial multiplier, and on-chip test systems based on RSFQ shift registers and on SFQ samplers. They enable test and study of RSFQ circuits at full GHz speed while communicating with semiconductor electronics at low speed.>

Digest of technical papers/Digest of technical papers - IEEE International Solid-State Circuits Conference•Dec 17, 2002•8 citations

4-bit rapid single-flux-quantum decoder

Alex F. Kirichenko, Vasili K. Semenov, Ying Ki Kwong +1 more

We describe the design of a fast single-flux-quantum decoder which can be used, e.g., in fast RAMs, general-purpose microprocessors, and communication channel switches. The core of the circuit is a tree of the single-bit SFQ demultiplexer with toggle (rather than the reset-set) control. Three new RSFQ cells: the demultiplexer, D flip-flop with complementary outputs, and serial XOR with large parameter tolerances (dc bias margins of /spl plusmn/25%, /spl plusmn/26%, and /spl plusmn/27%, respectively) have been developed for the decoder project. We have designed the first 16-bit prototype of the decoder for 1-kA/cm/sup 2/ niobium-trilayer technology and tested it at low frequencies. The circuit was completely operable except for 3 (of 16) output SFQ/DC converters. Simulations show that the circuit should allow data rate in excess of 60 Gbit/s and channel switching time below 20 ps.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•28 citations
We present a new design of a Rapid Single-Flux-Quantum (RSFQ) all-digital one-bit autocorrelator for submillimeter spectrometry applications, featuring 4 GHz input signal bandwidth, double oversampling quantizer, and 16 Mbps-per-channel output rate. The delay line of the autocorrelator is based on a circular shift register with XOR gates performing multiplication of the delayed and undelayed single-bit signals at every stage. The multiplication results are accumulated by room-temperature electronics after being prescaled in on-chip binary counters consisting of 10 T flip-flops per stage. We report results of experimental testing of a 16-stage autocorrelator delay line with multiplication and for a linear array of 8 low-power T flip-flop binary counters, all fabricated in HYPRES' standard 3.5 /spl mu/m 1000 A/cm/sup 2/ Nb-trilayer process. We also discuss physical and technical limits of the minimal power dissipation in RSFQ circuits.
We present the design of a rapid single-flux-quantum all-digital 1-bit autocorrelator for submillimeter spectrometry applications, featuring 4-GHz input signal bandwidth, double oversampling quantizer, and 16-Mb/s-per-channel output rate. The correlator consists of a digital delay line with multiplication and an array of accumulators with parallel readout. We report experimental results for a three-stage delay line (294 Josephson junctions) and a 4/spl times/4 array of accumulators (288 Josephson junctions) fabricated in HYPRES' standard 3.5-/spl mu/m 1000-A/cm/sup 2/ Nb-trilayer process.
We present the results of low- and high-speed testing of a fully integrated all-digital one-bit RSFQ autocorrelator for short-millimeter and submillimeter wave spectrometry applications. The 16-channel device, complete with a 16/spl times/9 array of binary counters, on-chip double-oversampling quantizer and on-chip clock was operational at clock speeds of up to 11 GHz. The total number of Josephson junctions in the design was 1672, while the estimated total power dissipation was less than 0.1 mW. For high-speed testing of the device we have developed a specialized 16-channel room-temperature interface capable of real-time data acquisition at a 16 Mbps-per-channel output rate. Extensive high-speed on-chip testing of the autocorrelator has also been performed, both in analog and digital modes, in the latter mode with an additional on-chip clock controller. All chips were fabricated in HYPRES' standard 3.5 /spl mu/m-10 /spl mu/A//spl mu/m/sup 2/ Nb-trilayer process. We also present a new concept of a 128-channel autocorrelator system built on 8 independent identical chips with approximately 2,500 Josephson junctions per chip, i.e. within the reach of the present-day fabrication technology.
A new generation of the Josephson digital circuits-rapid single flux quantum (RSFQ) devices-based on overdamped externally shunted high quality Nb-AlO x -Nb tunnel junctions have been designed, fabricated and experimentally investigated. All-refractory material 11-layer 5 mu m integrated technology has been successfully employed for the preparation of the RSFQ microcircuits. The T flip-flop has been demonstrated to operate properly up to clock frequencies of 100 GHz at 25% margins. The proper operation of the buffer stage for a one-directional SFQ pulse transmission at clock frequencies up to 125 GHz has been achieved. The possibilities to convert the information from the usual DC form to SFQ and vice versa have been demonstrated. An output signal in an SFQ/DC converter as high as 220 mu V has been measured. A new counter type A/D converter which includes a comparator and reversible binary counter with DC outputs has been fabricated and tested. The proposed ADC seems to be very promising for high-accuracy measurement of medium-bandwidth signals. The possibilities of creating a number of SFQ devices with outstanding parameters are discussed.
We describe the design of an oversampling single-flux-counting analog-to-digital converter with the estimated bandwidth of a few tens of MHz, based on Rapid Single-Flux-Quantum (RSFQ) devices. It consists of an input analog circuit, high-speed quantizer with an original analog/digital negative feedback loop, decimation (comb) filter, and supporting subsystems including clock distribution circuits, quantization signal conditioner, and output drivers. We have applied a new approach, the 'symmetrizing' negative feedback, to free the quantizer from the intrinsic hysteresis without dynamic range sacrifice. The 16-bit version of the system comprises about 1,500 Josephson junctions and consumes 1.2 mW of DC power, when implemented using Nb-trilayer technology with 1 kA/cm/sup 2/, 3.5 /spl mu/m Josephson junctions. All subsystems of the converter have been successfully tested and testing of the system as a whole is in progress.>
Key digital circuits for signal processing with tens of gigahertz speed and a few microwatts power dissipation have been recently demonstrated using a simple, 2 /spl mu/m linewidth process. These are the fastest digital circuits reported to date. These circuits use novel rapid single flux quantum (RSFQ) technology that takes advantage of the fundamental properties of superconductivity. In this technology, data and clock are picosecond-long quantized voltage pulses corresponding to the transfer of single magnetic flux quanta, /spl Phisub 0/=h/2e=2 mVps. These SFQ pulses are regenerated at each gate and are processed by circuits comprised of overdamped Josephson junctions interconnected via microstrip inductances. The inherent internal memory of all RSFQ gates (primarily flip-flops), combined with high switching speed, makes serial, bit-pipelined circuit design advantageous. This paper presents experiments in RSFQ digital circuits, including an N/spl times/8b serial multiplier, and on-chip test systems based on RSFQ shift registers and on SFQ samplers. They enable test and study of RSFQ circuits at full GHz speed while communicating with semiconductor electronics at low speed.>
We describe the design of a fast single-flux-quantum decoder which can be used, e.g., in fast RAMs, general-purpose microprocessors, and communication channel switches. The core of the circuit is a tree of the single-bit SFQ demultiplexer with toggle (rather than the reset-set) control. Three new RSFQ cells: the demultiplexer, D flip-flop with complementary outputs, and serial XOR with large parameter tolerances (dc bias margins of /spl plusmn/25%, /spl plusmn/26%, and /spl plusmn/27%, respectively) have been developed for the decoder project. We have designed the first 16-bit prototype of the decoder for 1-kA/cm/sup 2/ niobium-trilayer technology and tested it at low frequencies. The circuit was completely operable except for 3 (of 16) output SFQ/DC converters. Simulations show that the circuit should allow data rate in excess of 60 Gbit/s and channel switching time below 20 ps.>