Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Electromagnetic waves

MICROWAVE RESONATORS FOR WEAK LIGHT DETECTION AT TELECOM WAVELENGTH

Pin-Jia Zhou, Yiwen Wang, Qiang Wei, Lian-Fu Wei

Published Jan 1, 2014• 0 citations
Publisher

Abstract

We report the experimental measurements of weak light signal at 1550 nm wavelength with a high-quality factor microwave coplanar waveguide (CPW) resonators.The quality factor of this niobium λ/4 CPW resonator is measured as Q = 7.4 × 10 5 at ultra-low temperature (20 mK).With this device, we developed a technique to implement the proper fiber-resonator coupling, and realized the desirable weak light detection at telecommunication wavelength with 35 pW resolution by probing the shift of resonance frequency (f 0 ).We found that the resonator shift increases with the increasing light power (from 11.7 pW to 9.77 nW), similar to the effects of increasing the system temperature (from 20 mK to 800 mK).The observed blue shifts of f 0 (with the increasing of either the temperature and the applied light powers) are thoroughly deviated from the usual Mattis-Bardeen theory prediction, and could be explained by the effects relating to the two-level system existed on surface of the CPW device.

DOI
10.2528/pier14050308

Related papers

Experimental demonstrations of high-Q superconducting coplanar waveguide resonators

HaiJie Li, YiWen Wang, LianFu Wei +6 more

We successfully designed and fabricated an absorption-type of superconducting coplanar waveguide (CPW) resonators. The resonators are made from a niobium film (about 160 nm thick) on a high-resistance Si substrate, and each resonator is fabricated as a meandered quarter-wavelength transmission line (one end is short to the ground and another end is capacitively coupled to a through feedline). With a vector network analyzer we measured the transmissions of the applied microwave through the resonators at ultra-low temperature. The obtained loaded quality factors are significantly high, i.e. up to ∼10 6 . When the temperature increases slowly from the base temperature (20 mK), the resonance frequencies of the resonators are blue shifted and the quality factors are lowered slightly. In principle, this type of device can integrate a series of CPW resonators with a common feedline, making it a promising candidate as the data bus for coupling distant solid-state qubits and the sensitive detector of single photons.

arXiv:1304.3254•Chinese Science Bulletin•Jul 1, 2013•29 citations

Anomalous Temperature Dependence of the Quality Factor in a Superconducting Coplanar Waveguide Resonator

Pin-Jia Zhou, Yiwen Wang, Lian-Fu Wei

We present the measurements of the temperature dependence of the internal quality factor ( Q i ) of a microwave resonator, well below the superconducting transition temperature. The device is a quarter-wavelength niobium ( T c = 9.2 K) coplanar waveguide resonator. The measured | S 21 | parameter shows typically the skewed Lorentzian distributions, from which the fitted quality factor monotonically decreases with the temperature increasing from 30 mK to 900 mK. It is observed that for the lower temperature range (i.e., at T < 700 mK) the temperature dependence of the fitted Q i deviates significantly from the predictions of the usual Mattis—Bardeen theory. The measured 3 dB internal quality factor Q ′ i also verifies such an anomalous temperature dependence. Physically, this phenomenon could be attributed dominantly to the effects of the two-level systems in the device, rather than the usual temperature-dependent complex conductance.

Chinese Physics Letters•Jun 1, 2014•2 citations

Power-dependence measurement of the quality factor of superconducting microwave resonators at mK temperature

Seon Hoo Kim, Dong-Gwang Ha, Gwan Yeol Park +7 more

We report our setup and measurement results of the quality factor Q of superconducting microwave resonators at mK temperature in a dilution refrigerator. The power dependence of the superconducting resonators' Q was measured down to the single photon level. Measurements were performed on two types of microwave resonators. First, a half-wavelength coplanar waveguide (CPW) resonator made of niobium film on an oxidized high-resistivity silicon substrate was measured. Then a rectangular box resonator made of machined superconducting aluminum alloy was measured. While the CPW chip resonator's Q value showed noticeable decrease at low microwave power, the box resonator's Q showed little power dependence. This setup is intended to perform characterization of various microwave resonators, which will serve as key components in superconducting qubit in circuit QED architecture.

Conference on Precision Electromagnetic Measurements•Aug 1, 2014•2 citations

Characterizing Niobium Nitride-Based Superconducting Coplanar Waveguide Resonators for Microwave Hybrid Circuit Quantum Electrodynamics

Paniz Foshat, Paul Baity, Sergey Danilin +8 more

The high critical magnetic field and relatively high critical temperature of niobium nitride (NbN) make it a promising material for applications in superconducting quantum technology. However, NbN-based superconducting circuits are sensitive to decoherence sources such as two-level system (TLS) defects. Here, we numerically and experimentally investigate NbN superconducting microwave coplanar waveguide resonator arrays with a 100 nm thickness, capacitively coupled to a common coplanar waveguide on a silicon chip. We observe that the resonators' internal quality factor ($Q_{i}$) decreases from$Q_{i}\sim 1.07\times 10^{6}$in a high power regime to$Q_{i}\sim 1.36\times 10^{5}$in the single photon regime. Data from this study is consistent with the TLS theory, which describes the TLS interactions in resonator substrates and interfaces. Moreover, we study the temperature ($T$) dependence of$Q_{i}$and resonance frequency$f_{r}$of coplanar waveguide resonators to characterize the quasiparticle density. We observe that the increase in kinetic inductance at higher temperatures is the main reason for the frequency shift. Finally, we measure$f_{r}$and$Q_{i}$in response to in-plane magnetic fields ($B_{||}$). We verify that$Q_{i}$stays well above$10^{4}$up to$B_{||}$= 240 mT in the photon number$< \! n_{ph} \! >$= 1.8 at$T$= 100 mK. Our results could enable the development of robust microwave superconducting circuits for circuit quantum electrodynamics at high magnetic fields required for hybrid superconducting-semiconducting quantum circuits.

arXiv:2306.02356•IEEE Transactions on Applied Superconductivity•Jan 22, 2025•18 citations

Low-loss single-photon NbN microwave resonators on Si

Faustin W. Carter, Trupti Khaire, C. L. Chang +1 more

We present coplanar waveguide (CPW) microwave resonators with exceptionally low loss produced from NbN sputtered on Si. The NbN films are deposited with a modest RF substrate bias during reactive DC magnetron sputtering at a substrate temperature of 250 °C and can achieve a critical temperature as high as 15 K depending on the N2 flow rate. We measure the internal quality factors (Qi) of two such resonators at high-powers near saturation and report high-power quality factors in excess of 1.2 × 106 at 200 mK and 3.5 × 105 at 2 K. We also measure the temperature-dependent frequency shift at high power levels and the quality factor at single-photon power levels. From these measurements, we find a low-power (average photon number less than one) Qi value of 4.2 × 105 at 200 mK, which is consistent with a system limited by two-level-system loss.

Applied Physics Letters•Aug 26, 2019•38 citations

Low-loss superconducting aluminum microwave coplanar waveguide resonators on sapphires for the qubit readouts

Qing He, P. H. Ouyang, Haiyan Gao +7 more

Abstract The coplanar waveguide (CPW) microwave resonators have been widely applied for solid-state quantum computation and single-photon detection. Based on the physical analysis for the high fidelity readouts of the qubit(s), in this paper we design and then fabricate accordingly the desired aluminum (Al) film quarter-wavelength resonators on sapphire substrates. The ultra-low temperature measurement results show that the linearity of the internal quality factor under the proper driving power is satisfied well for the high fidelity readouts of the qubit(s); and the phase- and amplitude fractional frequency noises are significantly less for avoiding the potential information false alarms of the detected qubit during the readouts. With the demonstrated qubit-resonator experimental parameters, we argue that the designed and fabricated quarter-wavelength CPW resonators, with optimized parameters, can be used to implement the desired weakly perturbing readout measurements of the solid-state qubits on-chip.

Superconductor Science and Technology•Apr 25, 2022•12 citations
We report the experimental measurements of weak light signal at 1550 nm wavelength with a high-quality factor microwave coplanar waveguide (CPW) resonators.The quality factor of this niobium λ/4 CPW resonator is measured as Q = 7.4 × 10 5 at ultra-low temperature (20 mK).With this device, we developed a technique to implement the proper fiber-resonator coupling, and realized the desirable weak light detection at telecommunication wavelength with 35 pW resolution by probing the shift of resonance frequency (f 0 ).We found that the resonator shift increases with the increasing light power (from 11.7 pW to 9.77 nW), similar to the effects of increasing the system temperature (from 20 mK to 800 mK).The observed blue shifts of f 0 (with the increasing of either the temperature and the applied light powers) are thoroughly deviated from the usual Mattis-Bardeen theory prediction, and could be explained by the effects relating to the two-level system existed on surface of the CPW device.
We successfully designed and fabricated an absorption-type of superconducting coplanar waveguide (CPW) resonators. The resonators are made from a niobium film (about 160 nm thick) on a high-resistance Si substrate, and each resonator is fabricated as a meandered quarter-wavelength transmission line (one end is short to the ground and another end is capacitively coupled to a through feedline). With a vector network analyzer we measured the transmissions of the applied microwave through the resonators at ultra-low temperature. The obtained loaded quality factors are significantly high, i.e. up to ∼10 6 . When the temperature increases slowly from the base temperature (20 mK), the resonance frequencies of the resonators are blue shifted and the quality factors are lowered slightly. In principle, this type of device can integrate a series of CPW resonators with a common feedline, making it a promising candidate as the data bus for coupling distant solid-state qubits and the sensitive detector of single photons.
We present the measurements of the temperature dependence of the internal quality factor ( Q i ) of a microwave resonator, well below the superconducting transition temperature. The device is a quarter-wavelength niobium ( T c = 9.2 K) coplanar waveguide resonator. The measured | S 21 | parameter shows typically the skewed Lorentzian distributions, from which the fitted quality factor monotonically decreases with the temperature increasing from 30 mK to 900 mK. It is observed that for the lower temperature range (i.e., at T < 700 mK) the temperature dependence of the fitted Q i deviates significantly from the predictions of the usual Mattis—Bardeen theory. The measured 3 dB internal quality factor Q ′ i also verifies such an anomalous temperature dependence. Physically, this phenomenon could be attributed dominantly to the effects of the two-level systems in the device, rather than the usual temperature-dependent complex conductance.
We report our setup and measurement results of the quality factor Q of superconducting microwave resonators at mK temperature in a dilution refrigerator. The power dependence of the superconducting resonators' Q was measured down to the single photon level. Measurements were performed on two types of microwave resonators. First, a half-wavelength coplanar waveguide (CPW) resonator made of niobium film on an oxidized high-resistivity silicon substrate was measured. Then a rectangular box resonator made of machined superconducting aluminum alloy was measured. While the CPW chip resonator's Q value showed noticeable decrease at low microwave power, the box resonator's Q showed little power dependence. This setup is intended to perform characterization of various microwave resonators, which will serve as key components in superconducting qubit in circuit QED architecture.
The high critical magnetic field and relatively high critical temperature of niobium nitride (NbN) make it a promising material for applications in superconducting quantum technology. However, NbN-based superconducting circuits are sensitive to decoherence sources such as two-level system (TLS) defects. Here, we numerically and experimentally investigate NbN superconducting microwave coplanar waveguide resonator arrays with a 100 nm thickness, capacitively coupled to a common coplanar waveguide on a silicon chip. We observe that the resonators' internal quality factor (QiQ_{i}Qi​) decreases fromQi∼1.07×106Q_{i}\sim 1.07\times 10^{6}Qi​∼1.07×106in a high power regime toQi∼1.36×105Q_{i}\sim 1.36\times 10^{5}Qi​∼1.36×105in the single photon regime. Data from this study is consistent with the TLS theory, which describes the TLS interactions in resonator substrates and interfaces. Moreover, we study the temperature (TTT) dependence ofQiQ_{i}Qi​and resonance frequencyfrf_{r}fr​of coplanar waveguide resonators to characterize the quasiparticle density. We observe that the increase in kinetic inductance at higher temperatures is the main reason for the frequency shift. Finally, we measurefrf_{r}fr​andQiQ_{i}Qi​in response to in-plane magnetic fields (B∣∣B_{||}B∣∣​). We verify thatQiQ_{i}Qi​stays well above10410^{4}104up toB∣∣B_{||}B∣∣​= 240 mT in the photon number< ⁣nph ⁣>< \! n_{ph} \! ><nph​>= 1.8 atTTT= 100 mK. Our results could enable the development of robust microwave superconducting circuits for circuit quantum electrodynamics at high magnetic fields required for hybrid superconducting-semiconducting quantum circuits.
We present coplanar waveguide (CPW) microwave resonators with exceptionally low loss produced from NbN sputtered on Si. The NbN films are deposited with a modest RF substrate bias during reactive DC magnetron sputtering at a substrate temperature of 250 °C and can achieve a critical temperature as high as 15 K depending on the N2 flow rate. We measure the internal quality factors (Qi) of two such resonators at high-powers near saturation and report high-power quality factors in excess of 1.2 × 106 at 200 mK and 3.5 × 105 at 2 K. We also measure the temperature-dependent frequency shift at high power levels and the quality factor at single-photon power levels. From these measurements, we find a low-power (average photon number less than one) Qi value of 4.2 × 105 at 200 mK, which is consistent with a system limited by two-level-system loss.
Abstract The coplanar waveguide (CPW) microwave resonators have been widely applied for solid-state quantum computation and single-photon detection. Based on the physical analysis for the high fidelity readouts of the qubit(s), in this paper we design and then fabricate accordingly the desired aluminum (Al) film quarter-wavelength resonators on sapphire substrates. The ultra-low temperature measurement results show that the linearity of the internal quality factor under the proper driving power is satisfied well for the high fidelity readouts of the qubit(s); and the phase- and amplitude fractional frequency noises are significantly less for avoiding the potential information false alarms of the detected qubit during the readouts. With the demonstrated qubit-resonator experimental parameters, we argue that the designed and fabricated quarter-wavelength CPW resonators, with optimized parameters, can be used to implement the desired weakly perturbing readout measurements of the solid-state qubits on-chip.