Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE International Superconductive Electronics Conference (ISEC)

Influence of external magnetic fields on the inductive properties of rapid single-flux-quantum digital circuits

Romain Collot, Pascal Febvre, Jean-Luc Issler, Thierry Robert, Coenrad Johann Fourie, J. Kunert, Ronny Stolz, Hans‐Georg Meyer

Published Jul 1, 2013• 3 citations
Publisher

Abstract

A method has been developped to take into account the presence of a local external magnetic field in Superconducting Quantum Interference Devices (SQUIDs) loops composing Rapid Single-Flux-Quantum (RSFQ) circuits, through modifications of circuit inductances. A good agreement is observed between analytical formulas and simulations performed by time-domain softwares. The agreement with the first experiments is still only qualitative at this stage.

DOI
10.1109/isec.2013.6604269

Related papers

Operation of Low-$T_{c}$ Circuits in a Magnetic Environment

Romain Collot, Pascal Febvre, J. Kunert +1 more

Low-Tcrapid single flux quantum (RSFQ) digital circuits without magnetic shielding fabricated with the FLUXONICS Foundry have been studied in the presence of external magnetic fields. Magnetic fields parallel to the plane of the chip are shown to influence more drastically the nominal behavior of the circuits above 5 μT, while perpendicular magnetic fields can reach 15 μT without affecting significantly their operation. This is confirmed by experimental SQUID interference patterns.

IEEE Transactions on Applied Superconductivity•Dec 10, 2012•15 citations

Experimental evaluation of some rapid single flux quantum cells

Ying Ki Kwong, V. Nandakumar

Some basic cells in the rapid single-flux quantum (RSFQ) family of superconductive logic circuits were studied. An input stage, a buffer, and an OR gate were simulated and laid out for a standard niobium-based fabrication process. The resulting circuits perform properly for clock speeds up to 1 GHz. For the simpler circuits tested, the measured margins are wide, consistent with simulations, and not very dependent on clock speed. However, margin decreases with increased circuit complexity. The input stage converts a rising edge into an SFQ pulse, which has a small amplitude and narrow width in time. On the present circuits, these pulses are about 200 mu V in amplitude and 10 ps in width. To facilitate measurement, the authors have chosen as the output an asymmetrical superconducting quantum interference device (SQUID) consisting of two Josephson junctions. It converts SFQ pulses into 2.5 mV latching output levels on chip. By inductively coupling SFQ pulses into the SQUID loop, DC current isolation between the RSFQ circuit-under-test and the output stage is provided. The SQUID was optimized for 2 GHz operations.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•7 citations

Influence of the Superconducting Ground Plane on the Performance of RSFQ Cells

Ruben van Staden, Kyle Jackman, Coenrad Johann Fourie +1 more

Single-flux-quantum (SFQ) digital circuits are mostly based on cells that rely on reliable foundry processes that make use of a superconducting ground plane as a reference for the active elements and the microstrip line interconnects. The quantum of magnetic flux h/2e, associated with the binary information, corresponds to a magnetic field energy density that needs to be localized in space to limit interactions between adjacent cells. In other words, mutual inductances can harm the proper behaviour of circuits unless they are taken carefully into account during the design phase. We studied extensively the Josephson transmission line cell with different geometrical configurations of the ground plane and bias pads. We found with the use of InductEx that the return current sometimes follows paths that are far from what intuition tells, which can lead to nonoptimized designs. In this paper, we emphasize the limitations due to the presence of external or internal magnetic fields. Then, we compare obtained performances with the ones with optimized geometries for which the presence of the magnetic field is taken into account from the design phase.

IEEE Transactions on Applied Superconductivity•Jan 17, 2017•5 citations

[INVITED] Digital magnetometers based on the Single-Flux-Quantum technique

Pascal Febvre, Stolz, Ronny, Meyer, Hans-Georg +5 more

Superconducting Quantum Interference Devices (SQUIDs) are known to be the most sensitive magnetometers. We present a new type of low-Tc digital SQUID that is based on Rapid-Single-Flux-Quantum (RSFQ) Logic. It allows the on-chip conversion of the detected magnetic field into a digital form, suitable for noiseless processing, very high dynamic range and high slew rate. The sensitivity, limited to one magnetic single flux quantum, and a dynamic range of 76 dB, that corresponds to an upper limit of the magnetic field amplitude higher than 5 μT, have been measured along with overnight stability. First signatures of magnetic fields have been observed simultaneously with the ones of analogue SQUIDs in the ultra low noise environment of the Laboratoire Souterrain à Bas Bruit (LSBB) located in Rustrel, Provence, France.

•Jun 15, 2009•0 citations

Influence of external magnetic fields on the inductive properties of rapid single-flux-quantum digital circuits

Pascal Febvre, Romain Collot, J-L. Issler +4 more

•Jul 7, 2013•0 citations

Rapid single-flux quantum control of the energy potential in a double SQUID qubit circuit

Maria Gabriella Castellano, F. Chiarello, Roberto Leoni +6 more

We report on the development and test of an integrated system composed of a flux qubit and a rapid single-flux quantum (RSFQ) circuit that allows qubit manipulation. The goal is to demonstrate the feasibility of control electronics integrated on the same chip as the qubit, in view of the application in quantum computation with superconducting devices. RSFQ logic relies on the storage and transmission of magnetic flux quanta and can be profitably used with superconducting qubits because of the speed, scalability, compatibility with the qubit fabrication process and low temperature environment. While standard RSFQ circuitry is well assessed, the application to quantum computing requires a complete rescaling of parameter values, in order to preserve the qubit coherence and reduce the power dissipation. In the system presented in this paper, the qubit role is played by a superconducting loop interrupted by a small dc SQUID, usually called a double SQUID, which behaves as a tunable rf-SQUID. Its energy potential has the shape of a double well, with the barrier between the wells controlled by magnetic flux applied to the inner dc SQUID. Here for the first time we report measurements at a base temperature of 370 mK in which flux control pulses with desired characteristics were supplied by a RSFQ circuit fabricated using non-standard parameters in the same chip as the qubit.

Superconductor Science and Technology•May 3, 2007•16 citations
A method has been developped to take into account the presence of a local external magnetic field in Superconducting Quantum Interference Devices (SQUIDs) loops composing Rapid Single-Flux-Quantum (RSFQ) circuits, through modifications of circuit inductances. A good agreement is observed between analytical formulas and simulations performed by time-domain softwares. The agreement with the first experiments is still only qualitative at this stage.
Operation of Low-TcT_{c}Tc​ Circuits in a Magnetic Environment
Some basic cells in the rapid single-flux quantum (RSFQ) family of superconductive logic circuits were studied. An input stage, a buffer, and an OR gate were simulated and laid out for a standard niobium-based fabrication process. The resulting circuits perform properly for clock speeds up to 1 GHz. For the simpler circuits tested, the measured margins are wide, consistent with simulations, and not very dependent on clock speed. However, margin decreases with increased circuit complexity. The input stage converts a rising edge into an SFQ pulse, which has a small amplitude and narrow width in time. On the present circuits, these pulses are about 200 mu V in amplitude and 10 ps in width. To facilitate measurement, the authors have chosen as the output an asymmetrical superconducting quantum interference device (SQUID) consisting of two Josephson junctions. It converts SFQ pulses into 2.5 mV latching output levels on chip. By inductively coupling SFQ pulses into the SQUID loop, DC current isolation between the RSFQ circuit-under-test and the output stage is provided. The SQUID was optimized for 2 GHz operations.>
Single-flux-quantum (SFQ) digital circuits are mostly based on cells that rely on reliable foundry processes that make use of a superconducting ground plane as a reference for the active elements and the microstrip line interconnects. The quantum of magnetic flux h/2e, associated with the binary information, corresponds to a magnetic field energy density that needs to be localized in space to limit interactions between adjacent cells. In other words, mutual inductances can harm the proper behaviour of circuits unless they are taken carefully into account during the design phase. We studied extensively the Josephson transmission line cell with different geometrical configurations of the ground plane and bias pads. We found with the use of InductEx that the return current sometimes follows paths that are far from what intuition tells, which can lead to nonoptimized designs. In this paper, we emphasize the limitations due to the presence of external or internal magnetic fields. Then, we compare obtained performances with the ones with optimized geometries for which the presence of the magnetic field is taken into account from the design phase.
Superconducting Quantum Interference Devices (SQUIDs) are known to be the most sensitive magnetometers. We present a new type of low-Tc digital SQUID that is based on Rapid-Single-Flux-Quantum (RSFQ) Logic. It allows the on-chip conversion of the detected magnetic field into a digital form, suitable for noiseless processing, very high dynamic range and high slew rate. The sensitivity, limited to one magnetic single flux quantum, and a dynamic range of 76 dB, that corresponds to an upper limit of the magnetic field amplitude higher than 5 μT, have been measured along with overnight stability. First signatures of magnetic fields have been observed simultaneously with the ones of analogue SQUIDs in the ultra low noise environment of the Laboratoire Souterrain à Bas Bruit (LSBB) located in Rustrel, Provence, France.
We report on the development and test of an integrated system composed of a flux qubit and a rapid single-flux quantum (RSFQ) circuit that allows qubit manipulation. The goal is to demonstrate the feasibility of control electronics integrated on the same chip as the qubit, in view of the application in quantum computation with superconducting devices. RSFQ logic relies on the storage and transmission of magnetic flux quanta and can be profitably used with superconducting qubits because of the speed, scalability, compatibility with the qubit fabrication process and low temperature environment. While standard RSFQ circuitry is well assessed, the application to quantum computing requires a complete rescaling of parameter values, in order to preserve the qubit coherence and reduce the power dissipation. In the system presented in this paper, the qubit role is played by a superconducting loop interrupted by a small dc SQUID, usually called a double SQUID, which behaves as a tunable rf-SQUID. Its energy potential has the shape of a double well, with the barrier between the wells controlled by magnetic flux applied to the inner dc SQUID. Here for the first time we report measurements at a base temperature of 370 mK in which flux control pulses with desired characteristics were supplied by a RSFQ circuit fabricated using non-standard parameters in the same chip as the qubit.