Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Optics Express

Plasmonic superconducting nanowire single photon detector

Amin Eftekharian, Haig A. Atikian, A. Hamed Majedi

Published Jan 31, 2013• 28 citations
Publisher

Abstract

A theoretical analysis to enhance the quantum efficiency of a meander-line superconducting single photon detector without increasing the length or thickness of the active element is proposed. The general idea is to utilize the plasmonic nature of a superconducting layer to increase the surface absorption of the input optical signal. To satisfy both optical guiding and photon detection considerations of the design, a coefficient is introduced as a measure to maintain the device sensitivity while crossing over from the current crowding to vortex-based detection mechanisms.

DOI
10.1364/oe.21.003043

Related papers

Plasmonic Superconducting Single Photon Detector

Amin Eftekharian

A theoretical model with experimental verification is presented to enhance the quantum efficiency of a superconducting single-photon detector without increasing the length or thickness of the active element. The basic enhancement framework is based on: (1) Utilizing the plasmonic nature of a superconducting layer to increase the surface absorption of the input optical signal. (2) Enhancing the critical current of the nanowires by reducing the current crowding at the bend areas through optimally rounded-bend implementation. The experimental system quantum efficiency and fluctuation rates per second are assessed and compared to the proposed theoretical model. The model originated from an accurate description of the different liberation mechanisms of the nano-patterned superconducting films (vortex hopping and vortex-antivortex pairing). It is built complimentary to the existing, well-established models by considering the effects of quantum confinement on the singularities' energy states. The proposed model explains the dynamics of singularities for a wide range of temperatures and widths and describe an accurate count rate behavior for the structure. Furthermore, it explains the abnormal behaviors of the measured fluctuation rates occurring in wide nano-patterned superconducting structures below the critical temperature. In accordance to this model, it has been shown that for a typical strip width, not only is the vortex-antivortex liberation higher than the predicted rate, but also quantum tunneling is significant in certain conditions, and cannot be neglected as it has been in previous models. Also it is concluded that to satisfy both optical guiding and photon detection considerations of the design, the width and the thickness of the superconducting wires should be carefully determined in order to maintain the device sensitivity while crossing over from the current crowding to vortex-based detection mechanisms.

•Sep 26, 2013•1 citation

High quantum efficiency and low dark count rate in multi-layer superconducting nanowire single-photon detectors

Amir Jafari Salim, Amin Eftekharian, A. Hamed Majedi

In this paper, we theoretically show that a multi-layer superconducting nanowire single-photon detector (SNSPD) is capable of approaching characteristics of an ideal SNSPD in terms of the quantum efficiency, dark count, and band-width. A multi-layer structure improves the performance in two ways. First, the potential barrier for thermally activated vortex crossing, which is the major source of dark counts and the reduction of the critical current in SNSPDs is elevated. In a multi-layer SNSPD, a vortex is made of 2D-pancake vortices that form a stack. It will be shown that the stack of pancake vortices effectively experiences a larger potential barrier compared to a vortex in a single-layer SNSPD. This leads to an increase in the experimental critical current as well as significant decrease in the dark count rate. In consequence, an increase in the quantum efficiency for photons of the same energy or an increase in the sensitivity to photons of lower energy is achieved. Second, a multi-layer structure improves the efficiency of single-photon absorption by increasing the effective optical thickness without compromising the single-photon sensitivity.

Journal of Applied Physics•Feb 7, 2014•15 citations

Superconducting nanowire single-photon detectors integrated with optical nano-antennae

Xiaolong Hu, Eric A. Dauler, R. J. Molnar +1 more

Optical nano-antennae have been integrated with semiconductor lasers to intensify light at the nanoscale and photodiodes to enhance photocurrent. In quantum optics, plasmonic metal structures have been used to enhance nonclassical light emission from single quantum dots. Absorption and detection of single photons from free space could also be enhanced by nanometallic antennae, but this has not previously been demonstrated. Here, we use nano-optical transmission effects in a one-dimensional gold structure, combined with optical cavity resonance, to form optical nano-antennae, which are further used to couple single photons from free space into a 80-nm-wide superconducting nanowire. This antenna-assisted coupling enables a superconducting nanowire single-photon detector with 47% device efficiency at the wavelength of 1550 nm and 9-μm-by-9-μm active area while maintaining a reset time of only 5 ns. We demonstrate nanoscale antenna-like structures to achieve exceptional efficiency and speed in single-photon detection.

Optics Express•Dec 20, 2010•80 citations

Design of efficient superconducting nanowire single photon detectors for near-infrared wavelengths

M. J. A. de Dood

Superconducting single photon detectors consist of a narrow and thin wire of superconductor and can detect single photons with high efficiency and high speed. Simultaneous optimization of the detection efficiency and detector response time is difficult because the response time is set by the dimensions of the wire (cross section and length) while the detection efficiency is determined by both the internal detection mechanism and the dimensions of the wire. Wider and shorter wires are easier to fabricate, are more robust and lead to shorter detector reset time, but are generally less efficient. Experiments employing detector tomography provide important insights into the photon detection mechanism and indicate a detection mechanism where the edges of the wire are more efficient. This leads to a position dependent local detection efficiency that can be explained in the context of a photon-assisted-vortex-entry model and predicts an optimum wire width ~70 nm. A 50 nm wide silicon nanowire deposited on top of a 150 nm wide NbN nanowire directs light at 1550 nm wavelength to the edges and improves both the total absorption efficiency and the internal detection efficiency of the wire. The total absorption efficiency can be enhanced by 30% while the internal detection efficiency is increased by 70%. Assuming that the wire covers a similar area the detector response time is reduced 4-fold compared to the standard design using a 70 nm wide wire.

Advanced Photon Counting Techniques•May 14, 2018•0 citations

Supercontinuum single-photon detector using multilayer superconducting nanowires

Hao Li, Yong Wang, Lixing You +9 more

High-efficiency superconducting nanowire single-photon detectors (SNSPDs), which have numerous applications in quantum information systems, function by using the optical cavity and the ultrasensitive photon response of their ultra-thin superconducting nanowires. However, the wideband response of superconducting nanowires is limited due to the resonance of the traditional optical cavity. Here, we report on a supercontinuum SNSPD that can efficiently detect single photons over an ultra-broad spectral range from visible to mid-infrared light. Our detection approach relies on using multiple cavities with well-separated absorbed resonances formed by fabricating multilayer superconducting nanowires on metallic mirrors with silica acting as spacer layers. Thus, we are able to extend the absorption spectral bandwidth while maintaining considerable efficiency, as opposed to a conventional single-layer SNSPD. Our calculations show that the proposed supercontinuum SNSPD exhibits an extended absorption bandwidth with increased nanowire layers. Its absorption efficiency is greater than 70% over the entire range from 400 to 2500 nm (or 400 to 3000 nm), when using two-layer (or three-layer) nanowires. As a proof of principle, the SNSPD with bilayer nanowires is fabricated based on the proposed detector architecture with simplified geometrical parameters. The detector achieves broadband detection efficiency over 60% from 950 to 1650 nm. This type of detector may replace multiple narrow band detectors in a system and find uses in the emerging and rapidly advancing field of atomic and molecular broadband spectroscopy.

Photonics Research•Nov 20, 2019•22 citations

Design of NbN superconducting nanowire single photon detectors with enhanced infrared photon detection efficiency

Q. Wang, Jelmer J. Renema, Andreas Engel +1 more

Nanowire superconducting single-photon detectors (SSPDs) consist of a superconducting wire of nanoscale cross-section [1], typically 4×100 nm2. A current close to the device critical current renders the nanowire sensitive to single photons. SSPDs are known for their high efficiency, low jitter, low dark count rate and fast reset time. An important challenge for future application of SSPDs is to extend the useful wavelength range towards the infrared without comprising detector speed or dark count rate. To this end, we explore optical designs with wider nanowires that utilize efficient detection of single photons at the edge of the nanowire. Silicon nanowires on top of a NbN nanowire increase both the calculated total absorption and the internal detection efficiency significantly compared to a standard meandering wire geometry.

arXiv:1612.02840•Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jan 1, 2017•1 citation
A theoretical analysis to enhance the quantum efficiency of a meander-line superconducting single photon detector without increasing the length or thickness of the active element is proposed. The general idea is to utilize the plasmonic nature of a superconducting layer to increase the surface absorption of the input optical signal. To satisfy both optical guiding and photon detection considerations of the design, a coefficient is introduced as a measure to maintain the device sensitivity while crossing over from the current crowding to vortex-based detection mechanisms.
A theoretical model with experimental verification is presented to enhance the quantum efficiency of a superconducting single-photon detector without increasing the length or thickness of the active element. The basic enhancement framework is based on: (1) Utilizing the plasmonic nature of a superconducting layer to increase the surface absorption of the input optical signal. (2) Enhancing the critical current of the nanowires by reducing the current crowding at the bend areas through optimally rounded-bend implementation. The experimental system quantum efficiency and fluctuation rates per second are assessed and compared to the proposed theoretical model. The model originated from an accurate description of the different liberation mechanisms of the nano-patterned superconducting films (vortex hopping and vortex-antivortex pairing). It is built complimentary to the existing, well-established models by considering the effects of quantum confinement on the singularities' energy states. The proposed model explains the dynamics of singularities for a wide range of temperatures and widths and describe an accurate count rate behavior for the structure. Furthermore, it explains the abnormal behaviors of the measured fluctuation rates occurring in wide nano-patterned superconducting structures below the critical temperature. In accordance to this model, it has been shown that for a typical strip width, not only is the vortex-antivortex liberation higher than the predicted rate, but also quantum tunneling is significant in certain conditions, and cannot be neglected as it has been in previous models. Also it is concluded that to satisfy both optical guiding and photon detection considerations of the design, the width and the thickness of the superconducting wires should be carefully determined in order to maintain the device sensitivity while crossing over from the current crowding to vortex-based detection mechanisms.
In this paper, we theoretically show that a multi-layer superconducting nanowire single-photon detector (SNSPD) is capable of approaching characteristics of an ideal SNSPD in terms of the quantum efficiency, dark count, and band-width. A multi-layer structure improves the performance in two ways. First, the potential barrier for thermally activated vortex crossing, which is the major source of dark counts and the reduction of the critical current in SNSPDs is elevated. In a multi-layer SNSPD, a vortex is made of 2D-pancake vortices that form a stack. It will be shown that the stack of pancake vortices effectively experiences a larger potential barrier compared to a vortex in a single-layer SNSPD. This leads to an increase in the experimental critical current as well as significant decrease in the dark count rate. In consequence, an increase in the quantum efficiency for photons of the same energy or an increase in the sensitivity to photons of lower energy is achieved. Second, a multi-layer structure improves the efficiency of single-photon absorption by increasing the effective optical thickness without compromising the single-photon sensitivity.
Optical nano-antennae have been integrated with semiconductor lasers to intensify light at the nanoscale and photodiodes to enhance photocurrent. In quantum optics, plasmonic metal structures have been used to enhance nonclassical light emission from single quantum dots. Absorption and detection of single photons from free space could also be enhanced by nanometallic antennae, but this has not previously been demonstrated. Here, we use nano-optical transmission effects in a one-dimensional gold structure, combined with optical cavity resonance, to form optical nano-antennae, which are further used to couple single photons from free space into a 80-nm-wide superconducting nanowire. This antenna-assisted coupling enables a superconducting nanowire single-photon detector with 47% device efficiency at the wavelength of 1550 nm and 9-μm-by-9-μm active area while maintaining a reset time of only 5 ns. We demonstrate nanoscale antenna-like structures to achieve exceptional efficiency and speed in single-photon detection.
Superconducting single photon detectors consist of a narrow and thin wire of superconductor and can detect single photons with high efficiency and high speed. Simultaneous optimization of the detection efficiency and detector response time is difficult because the response time is set by the dimensions of the wire (cross section and length) while the detection efficiency is determined by both the internal detection mechanism and the dimensions of the wire. Wider and shorter wires are easier to fabricate, are more robust and lead to shorter detector reset time, but are generally less efficient. Experiments employing detector tomography provide important insights into the photon detection mechanism and indicate a detection mechanism where the edges of the wire are more efficient. This leads to a position dependent local detection efficiency that can be explained in the context of a photon-assisted-vortex-entry model and predicts an optimum wire width ~70 nm. A 50 nm wide silicon nanowire deposited on top of a 150 nm wide NbN nanowire directs light at 1550 nm wavelength to the edges and improves both the total absorption efficiency and the internal detection efficiency of the wire. The total absorption efficiency can be enhanced by 30% while the internal detection efficiency is increased by 70%. Assuming that the wire covers a similar area the detector response time is reduced 4-fold compared to the standard design using a 70 nm wide wire.
High-efficiency superconducting nanowire single-photon detectors (SNSPDs), which have numerous applications in quantum information systems, function by using the optical cavity and the ultrasensitive photon response of their ultra-thin superconducting nanowires. However, the wideband response of superconducting nanowires is limited due to the resonance of the traditional optical cavity. Here, we report on a supercontinuum SNSPD that can efficiently detect single photons over an ultra-broad spectral range from visible to mid-infrared light. Our detection approach relies on using multiple cavities with well-separated absorbed resonances formed by fabricating multilayer superconducting nanowires on metallic mirrors with silica acting as spacer layers. Thus, we are able to extend the absorption spectral bandwidth while maintaining considerable efficiency, as opposed to a conventional single-layer SNSPD. Our calculations show that the proposed supercontinuum SNSPD exhibits an extended absorption bandwidth with increased nanowire layers. Its absorption efficiency is greater than 70% over the entire range from 400 to 2500 nm (or 400 to 3000 nm), when using two-layer (or three-layer) nanowires. As a proof of principle, the SNSPD with bilayer nanowires is fabricated based on the proposed detector architecture with simplified geometrical parameters. The detector achieves broadband detection efficiency over 60% from 950 to 1650 nm. This type of detector may replace multiple narrow band detectors in a system and find uses in the emerging and rapidly advancing field of atomic and molecular broadband spectroscopy.
Nanowire superconducting single-photon detectors (SSPDs) consist of a superconducting wire of nanoscale cross-section [1], typically 4×100 nm2. A current close to the device critical current renders the nanowire sensitive to single photons. SSPDs are known for their high efficiency, low jitter, low dark count rate and fast reset time. An important challenge for future application of SSPDs is to extend the useful wavelength range towards the infrared without comprising detector speed or dark count rate. To this end, we explore optical designs with wider nanowires that utilize efficient detection of single photons at the edge of the nanowire. Silicon nanowires on top of a NbN nanowire increase both the calculated total absorption and the internal detection efficiency significantly compared to a standard meandering wire geometry.