Journal of Physics D Applied Physics

The properties of a heterodyne receiver at 450 GHz using a Josephson point-contact mixer and an external local oscillator

T. G. Blaney, N R Cross, Robert G. Jones

Published Nov 14, 1982• 12 citations

Abstract

Adjustable niobium Josephson point contacts, mounted in fundamental-mode waveguide cavities, have been used as mixers in an experimental heterodyne receiver with a 450 GHz laser as the local oscillator. It was possible to estimate separately the various factors, such as intrinsic mixer conversion efficiency, mixer noise, and input coupling efficiency that contribute to the overall receiver sensitivity. Mixer performance agreed reasonably well with qualitative predictions of resistively-shunted-junction theoretical models, and there was broad quantitative agreement for some aspects of performance. Spurious, and potentially very misleading non-heterodyne responses to thermal signals were observed under some regimes of applied DC bias and local oscillator power. The lowest overall receiver noise temperature measured was 2100K (double side band), although reduction to 1000K should be possible with quite simple improvements. The intrinsic mixer noise temperatures were usually in the range 500-1000K (single side band), and local oscillator power required by the receiver was usually less than one microwatt. This performance makes these mixers competitive as the basis of very sensitive near-millimetre-wave receivers.

DOI: 10.1088/0022-3727/15/11/007

Related papers

Heterodyne reception at 891 GHz using a Josephson harmonic mixer and a microwave local oscillator

T. G. Blaney, D. J. E. Knight

The performance of Nb-Nb point-contact Josephson junction mixers was investigated experimentally with signals from a 891 GHz laser. The local oscillator (LO) was provided by the appropriate junction-generated harmonic of either a 74 or 99 GHz klystron. The intermediate frequency (IF) power varied linearly with signal power for signals less than 10 −5 to 10 −6 W. The optimum conversion loss (from 891 GHz to the IF) was not significantly different for the two klystron frequencies used: the lowest useful conversion loss for the whole mixing system including the signal input matching loss, was 42 (±3) dB. This is 10 dB greater than that observed with a 891 GHz laser LO and the same junction apparatus. Conversion loss of the mixer element alone was independent of IF with the latter varied up to 1·2 GHz. The noise at the output of the IF system was usually dominated by that of the transistor preamplifier with a noise temperature of about 500 K. Thus the input signal necessary to give a signal-to-noise ratio of one at the IF was equivalent to 10 −16 W Hz −1 of IF bandwidth. This mixing system, which can be significantly improved, forms the basis of a fully tunable heterodyne receiver for the submillimetre region.

Journal of Physics D Applied PhysicsSep 21, 197411 citations

Heterodyne laser radiation detection at 891 GHz using josephson point contacts

T. G. Blaney

Experiments were carried out to investigate the performance of a heterodyne detector at 891 GHz using a cw hydrogen cyanide laser as the local oscillator and Nb-Nb point contact Josephson junctions as mixing devices. Using a second off-tuned HCN laser as the signal, intermediate frequencies (IF's) up to a few MHz could be studied. Both pre-set and adjustable types of junction were used, and the latter, arranged so that radiation could be directly focussed onto them gave the best ultimate sensitivity. Dependence of the IF power on dc current bias and local oscillator power is described, and compared with simple theory. IF power varied linearly with signal power for signals less than 10-5 to 10-6 W. The mixer conversion efficiency was independent of IF. The sensitivity of the detector was a strong function of junction characteristics and ranged over several orders of magnitude in the junctions studied. Noise at the output was dominated by the room temperature preamplifier with a noise temperature of about 500 K. The smallest observed value for conversion loss of the junction was about 29 dB. This figure includes the signal input matching loss. The best sensitivity of the whole receiving system was equivalent to 1 × 10-17 W/Hz.

Revue de Physique AppliquéeJan 1, 197420 citations

Point-contact Josephson mixers at 130 GHz

J. H. Claassen, P. L. Richards

The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.

Journal of Applied PhysicsJul 1, 197828 citations

Josephson heterodyne detection at high thermal background levels

Tim Poorter

Point-contact Josephson junctions with a submicron contact diameter have been used as high-frequency mixers (170–220 GHz) under high thermal background conditions. The junction is formed across a full height (0.56×1.06 mm2) waveguide between a 3–5-μm thick Nb whisker and a 0.2-mm diam Nb center conductor of a coaxial line. The best single-side band mixer-noise temperature that was measured is 165 K (± 25%) with a corresponding single-side band conversion efficiency of 0.36±0.03 (a loss of 4.5 ±0.4 dB) at a signal frequency of 185 GHz, including losses in the coupling horn and the waveguide. The performance was measured with the hot-cold source technique. The effects of nonheterodyne response in that situation were investigated in detail. The junctions have been operated in a coherent receiver that can be used on a telescope with only small adaptations. The instantaneous bandwidth of the receiver is about 20 GHz.

Journal of Applied PhysicsJan 1, 198227 citations

Noise and Conversion Efficiency of High-T c Superconductor Josephson Mixers

Oliver Harnack, S. Beuven, Marian Darula +4 more

We report on experimental studies of the noise performance and conversion efficiency of high-Te Josephson mixers at frequencies between 90 GHz and 550 GHz. The heterodyne mixing experiments have been performed by using YBa2Cu307_8 step-edge junctions and bicrystal junctions on MgO (E--9.6) substrates. We studied the Josephson mixer performance for the case of internal pumping (selfpumping) and external pumping. Receiver noise measurements in a waveg,uide setup for the case of external pumping at 90-94 GHz gave formally calculated double-side-band (DSB) mixer noise temperatures (Tm) of about 2000 K at physical temperatures of 10 K. Similar measurements in a quasioptical setup at 4.2 K and at operation frequencies of 430 GHz and 546 GHz yielded mixer noise temperatures of 1200 K and 1100 K, respectively. Using the internal pumped mode, i.e. mixing without external local oscillator signal, we also obtained clear IF response in hot/cold-measurements. The formally calculated Tm were between 580 K and 2300 K.

Softwaretechnik-TrendsMar 1, 19981 citation

Studies of noise in Josephson-effect mixers and their potential for submillimeter heterodyne detection

Robert J. Schoelkopf

NOTE: Text or symbols not renderable in plain ASCII are indicated by [...]. Abstract is included in .pdf document. This thesis describes both theoretical and experimental investigations into the dynamics and noise processes of Josephson junctions, with the intent of evaluating their potential as mixers in heterodyne instruments for submillimeter-wave (i.e., the frequency range from 300 GHz to 3THz) detection. Superconducting tunnel junctions utilizing the nonlinearity due to photon-assisted tunneling of quasiparticles (SIS mixers) have become the state-of-the-art technology for sensitive heterodyne detection up to frequencies of about 700 [...]. Recent progress in the fabrication of high [...], superconductors has led to Josephson-effect devices with [...] products of up to ten millivolts, which might be suitable for mixing at frequencies of many terahertz. The key question for weighing the prospects for high-frequency Josephson mixers is that of the sensitivity which can be attained. Previous experimental work on Josephson mixing suggests the existence of an "excess" noise, which degrades the sensitivity. Theoretical modeling of mixer performance, based on the resistivelyshunted junction (RSJ) model for the dynamics of the device, also indicates the presence of larger noise than expected. The origin of this noise was not clearly understood, however, nor was its exact magnitude or expected scaling with frequency or junction characteristics known. In addition, previous experiments utilized crude devices of the point-contact type, which were unstable and thus undesirable for real applications. In the first part of this thesis research, extensive numerical simulations were performed with the RSJ model, including calculations of mixer noise and conversion efficiency. These calculations have revealed that the source of excess noise is the AC Josephson oscillations of the device, which can be completely incoherent, with a linewidth comparable to their frequency. Thus they appear as a broadband noise source. While this noise is intrinsic and unavoidable, an optimized mixer is still shown to be capable of interesting sensitivity levels, and the excess noise is expected to become relatively less important as the operating frequency is increased. Secondly, a process has been developed for the fabrication of stable, well-characterized, and reproducible Josephson devices based on resistively-shunted Nb and NbN tunnel junctions. The devices utilize submicron-area, high current-density tunnel junctions and a AuGe shunt resistor to yield completely non-hysteretic I-V curves, normal-state resistances of about [...] products of about half a millivolt. These devices should be nearly optimal for mixing at [...]. Heterodyne measurements using these junctions have been performed in a waveguide mixer mount. Receiver temperatures as low as 190 K (DSB), with -6 dB conversion efficiency, have been obtained at 100 [...], but these results are still a factor of about four higher than those predicted by the RSJ simulations. Accurate measurements of the available noise power of the junctions at the intermediate frequency of 1.5 [...] were made, and confirmed that the receivers were limited by elevated junction output noise. The deviations of the noise from theoretical predictions are shown to be caused by the nonlinear interaction of the junction with the embedding circuit. While this work points out some of the complexity introduced by the strong nonlinearity of Josephson devices, it is still expected that Josephson-effect mixers may be useful for heterodyne detection at very high frequencies.

Nov 7, 20074 citations