Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Applied Physics

Josephson heterodyne detection at high thermal background levels

Tim Poorter

Published Jan 1, 1982• 27 citations
Publisher

Abstract

Point-contact Josephson junctions with a submicron contact diameter have been used as high-frequency mixers (170–220 GHz) under high thermal background conditions. The junction is formed across a full height (0.56×1.06 mm2) waveguide between a 3–5-μm thick Nb whisker and a 0.2-mm diam Nb center conductor of a coaxial line. The best single-side band mixer-noise temperature that was measured is 165 K (± 25%) with a corresponding single-side band conversion efficiency of 0.36±0.03 (a loss of 4.5 ±0.4 dB) at a signal frequency of 185 GHz, including losses in the coupling horn and the waveguide. The performance was measured with the hot-cold source technique. The effects of nonheterodyne response in that situation were investigated in detail. The junctions have been operated in a coherent receiver that can be used on a telescope with only small adaptations. The instantaneous bandwidth of the receiver is about 20 GHz.

DOI
10.1063/1.329957

Related papers

Point-contact Josephson mixers at 130 GHz

J. H. Claassen, P. L. Richards

The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.

Journal of Applied Physics•Jul 1, 1978•28 citations

The properties of a heterodyne receiver at 450 GHz using a Josephson point-contact mixer and an external local oscillator

T. G. Blaney, N R Cross, Robert G. Jones

Adjustable niobium Josephson point contacts, mounted in fundamental-mode waveguide cavities, have been used as mixers in an experimental heterodyne receiver with a 450 GHz laser as the local oscillator. It was possible to estimate separately the various factors, such as intrinsic mixer conversion efficiency, mixer noise, and input coupling efficiency that contribute to the overall receiver sensitivity. Mixer performance agreed reasonably well with qualitative predictions of resistively-shunted-junction theoretical models, and there was broad quantitative agreement for some aspects of performance. Spurious, and potentially very misleading non-heterodyne responses to thermal signals were observed under some regimes of applied DC bias and local oscillator power. The lowest overall receiver noise temperature measured was 2100K (double side band), although reduction to 1000K should be possible with quite simple improvements. The intrinsic mixer noise temperatures were usually in the range 500-1000K (single side band), and local oscillator power required by the receiver was usually less than one microwatt. This performance makes these mixers competitive as the basis of very sensitive near-millimetre-wave receivers.

Journal of Physics D Applied Physics•Nov 14, 1982•12 citations

Low-noise Josephson mixers at 115 GHz using recyclable point contacts

Y. Taur, Anthony R. Kerr

Thermally recyclable Nb point-contact Josephson junctions are investigated as low-noise mixers with an external local oscillator at 115 GHz. The best single sideband mixer noise temperature achieved is 140 (±20) K with a (SSB) conversion loss of 2.4 (±0.5) dB. Such rugged junctions are suitable for use in practical receivers and should give unprecedented sensitivity at the shorter millimeter wavelengths.

Applied Physics Letters•Jun 1, 1978•32 citations

Noise and Conversion Efficiency of High-T c Superconductor Josephson Mixers

Oliver Harnack, S. Beuven, Marian Darula +4 more

We report on experimental studies of the noise performance and conversion efficiency of high-Te Josephson mixers at frequencies between 90 GHz and 550 GHz. The heterodyne mixing experiments have been performed by using YBa2Cu307_8 step-edge junctions and bicrystal junctions on MgO (E--9.6) substrates. We studied the Josephson mixer performance for the case of internal pumping (selfpumping) and external pumping. Receiver noise measurements in a waveg,uide setup for the case of external pumping at 90-94 GHz gave formally calculated double-side-band (DSB) mixer noise temperatures (Tm) of about 2000 K at physical temperatures of 10 K. Similar measurements in a quasioptical setup at 4.2 K and at operation frequencies of 430 GHz and 546 GHz yielded mixer noise temperatures of 1200 K and 1100 K, respectively. Using the internal pumped mode, i.e. mixing without external local oscillator signal, we also obtained clear IF response in hot/cold-measurements. The formally calculated Tm were between 580 K and 2300 K.

Softwaretechnik-Trends•Mar 1, 1998•1 citation

Frequency conversion with superconducting point contacts operating as oscillator-mixers and its application to the measurement of the linewidth of the Josephson current at very high frequency

G. Vernet, Robert Adde

The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb-Nb point contact junctions at 4.2 K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1 and 9.2 GHz. Frequency conversion signals are only detected in the latter case with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1 600 GHz. The experiments with intermediate frequency fi of 0.1 GHz indicate for this small value of f i that the observed signals are not related to frequency conversion but noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. We have then investigated the noise properties up to 450 GHz of superconducting point-contacts using the junction as an oscillator-mixer where the Josephson current is mixed with harmonics of an externally applied signal. The emitted intermediate frequency is detected at 9.2 GHz and its linewidth is measured. In the very high frequency range the dc quasiparticle current dominates in a Josephson weak-link and we compare the corresponding theoretical linewidth calculated by Scalapino with our experimental results.

Revue de Physique Appliquée•Jan 1, 1974•3 citations

Experiments on a Point-Contact Josephson Mixer at 469 µm

Masayoshi Kobayashi, Shinji Ohara, Akira Katsuno +2 more

An Nb point-contact Josephson mixer with a corner reflector behind the Nb 4-wavelength wire antenna was constructed, and experiments were carried out at 469 µm (693 GHz). A 10 dB improvement in coupling efficiency was obtained by using the reflector. An SSB (single-side-band) mixer noise temperature of 1660 K was obtained, and the conversion efficiency of the mixer was -35.7 dB in the 9th harmonic mixing between 71 GHz LO and 693 GHz signal.

Japanese Journal of Applied Physics•Nov 1, 1985•1 citation
Point-contact Josephson junctions with a submicron contact diameter have been used as high-frequency mixers (170–220 GHz) under high thermal background conditions. The junction is formed across a full height (0.56×1.06 mm2) waveguide between a 3–5-μm thick Nb whisker and a 0.2-mm diam Nb center conductor of a coaxial line. The best single-side band mixer-noise temperature that was measured is 165 K (± 25%) with a corresponding single-side band conversion efficiency of 0.36±0.03 (a loss of 4.5 ±0.4 dB) at a signal frequency of 185 GHz, including losses in the coupling horn and the waveguide. The performance was measured with the hot-cold source technique. The effects of nonheterodyne response in that situation were investigated in detail. The junctions have been operated in a coherent receiver that can be used on a telescope with only small adaptations. The instantaneous bandwidth of the receiver is about 20 GHz.
The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.
Adjustable niobium Josephson point contacts, mounted in fundamental-mode waveguide cavities, have been used as mixers in an experimental heterodyne receiver with a 450 GHz laser as the local oscillator. It was possible to estimate separately the various factors, such as intrinsic mixer conversion efficiency, mixer noise, and input coupling efficiency that contribute to the overall receiver sensitivity. Mixer performance agreed reasonably well with qualitative predictions of resistively-shunted-junction theoretical models, and there was broad quantitative agreement for some aspects of performance. Spurious, and potentially very misleading non-heterodyne responses to thermal signals were observed under some regimes of applied DC bias and local oscillator power. The lowest overall receiver noise temperature measured was 2100K (double side band), although reduction to 1000K should be possible with quite simple improvements. The intrinsic mixer noise temperatures were usually in the range 500-1000K (single side band), and local oscillator power required by the receiver was usually less than one microwatt. This performance makes these mixers competitive as the basis of very sensitive near-millimetre-wave receivers.
We report on experimental studies of the noise performance and conversion efficiency of high-Te Josephson mixers at frequencies between 90 GHz and 550 GHz. The heterodyne mixing experiments have been performed by using YBa2Cu307_8 step-edge junctions and bicrystal junctions on MgO (E--9.6) substrates. We studied the Josephson mixer performance for the case of internal pumping (selfpumping) and external pumping. Receiver noise measurements in a waveg,uide setup for the case of external pumping at 90-94 GHz gave formally calculated double-side-band (DSB) mixer noise temperatures (Tm) of about 2000 K at physical temperatures of 10 K. Similar measurements in a quasioptical setup at 4.2 K and at operation frequencies of 430 GHz and 546 GHz yielded mixer noise temperatures of 1200 K and 1100 K, respectively. Using the internal pumped mode, i.e. mixing without external local oscillator signal, we also obtained clear IF response in hot/cold-measurements. The formally calculated Tm were between 580 K and 2300 K.
The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb-Nb point contact junctions at 4.2 K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1 and 9.2 GHz. Frequency conversion signals are only detected in the latter case with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1 600 GHz. The experiments with intermediate frequency fi of 0.1 GHz indicate for this small value of f i that the observed signals are not related to frequency conversion but noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. We have then investigated the noise properties up to 450 GHz of superconducting point-contacts using the junction as an oscillator-mixer where the Josephson current is mixed with harmonics of an externally applied signal. The emitted intermediate frequency is detected at 9.2 GHz and its linewidth is measured. In the very high frequency range the dc quasiparticle current dominates in a Josephson weak-link and we compare the corresponding theoretical linewidth calculated by Scalapino with our experimental results.