Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Review of Scientific Instruments

Optimization of a Josephson voltage array based on frequency dependently damped superconductor–insulator–superconductor junctions

Juha Hassel, Heikki Seppä, Leif Grönberg, Ilkka Suni

Published Jun 30, 2003• 18 citations
Publisher

Abstract

We have developed a programmable Josephson voltage standard based on an array of superconductor–insulator–superconductor junctions. The junctions are damped by an external frequency-dependent shunt circuit, which allows operation at Shapiro steps with n>1. We derive optimization criteria for the design parameters for a fast and stable array with low power consumption. An array able to generate 1.0 VRMS ac voltage signal with sub-ppm accuracy is experimentally demonstrated. Theoretically it is also shown that a fast programmable 10 V array can be realized.

DOI
10.1063/1.1582381

Related papers

Stimulated Power Generation in ES-SIS Junction Arrays

Juha Hassel, P. Helistö, Leif Grönberg +3 more

We present experimental results on new programmable Josephson voltage standards based on frequency dependently damped superconductor-insulator-superconductor (SIS) junctions. We introduce a design able to generate two independent floating voltages up to 1.5 V using a microwave frequency of 70 GHz. The array is developed for dc and ac voltage and impedance metrology. The design is optimized in terms of speed, power consumption, and stability. Stimulated power generation is shown to affect the performance of long SIS arrays. The collective dynamics of Josephson junctions is analyzed and a boundary condition for the design of long arrays is derived.

IEEE Transactions on Instrumentation and Measurement•Mar 21, 2005•8 citations

SIS junctions with frequency dependent damping for a programmable Josephson voltage standard

Juha Hassel, Heikki Seppä, Leif Grönberg +1 more

Experimental and computational results on programmable Josephson junction array (JJA) chips based on superconductor-insulator-superconductor (SIS) junctions are presented. Implications of circuit design and fabrication process on the performance are discussed. We introduce a method to decrease the attenuation of the pump microwave. Different designs are compared, suggesting that 1 V chips operating at the third constant voltage step with 70 GHz pump frequency can be produced with our process.

IEEE Transactions on Instrumentation and Measurement•Apr 1, 2001•24 citations

10 V SINIS Josephson junction series arrays for programmable voltage standards

J. Kohlmann, H. Schulze, Ralf Behr +2 more

A programmable dc voltage standard for output voltages of up to 10 V has been realized. The series arrays, consisting of about 69120 overdamped superconductor/insulator/normal metal/insulator/superconductor (SINIS) Josephson junctions, have been fabricated using the reliable Nb-Al/Al/sub 2/O/sub 3/ technology. The arrays can be operated in conventional Josephson voltage standards at microwave frequencies from 70 GHz to 75 GHz. Steps of constant voltage are observed at very low microwave power levels, since the major part of the microwave power is generated by the junctions themselves. The operation of the arrays and the formation of Shapiro steps are discussed.

IEEE Transactions on Instrumentation and Measurement•Apr 1, 2001•20 citations

Josephson Series Arrays for Programmable 10-V SINIS Josephson Voltage Standards and for Josephson Arbitrary Waveform Synthesizers Based on SNS Junctions

J. Kohlmann, F. Muller, Oliver Kieler +4 more

Programmable Josephson voltage standards for output voltages up to 10 V have been realized. Binary-divided series arrays consisting of 69 632 overdamped SINIS Josephson junctions have been fabricated using reliable Nb-Al/Al2O3technology (S: superconductor, I: insulator, N: normal metal). Series arrays of about 1000 SNS Josephson junctions were realized as lumped arrays for applications in the Josephson arbitrary waveform synthesizer (JAWS). We suggest a novel scheme for combining the higher voltages generated by the binary-divided arrays with the frequency spectral characteristics of the JAWS, in order to optimize the frequency spectrum of the generated ac voltages

IEEE Transactions on Instrumentation and Measurement•Mar 16, 2007•34 citations

Realization of a 2-V Programmable Josephson Junction Array Using Balanced Segmentation Scheme

Wenhui Cao, Jinjin Li, Yuan Zhong +4 more

This article proposes a balanced segmentation scheme to improve the microwave transmission and develops a 2-V programmable Josephson junction array using double-stacked superconductor-normal-metal-superconductor Josephson junctions. The junction numbers of the sub-Josephson arrays are divided into a ternary sequence. The least significant bit is one stack or two junctions. In order to characterize the chip with many subarrays, an automatic measurement system with self-made multichannel current sources was established. It can analyze the critical current, the margin of the voltage steps, and the number of junctions in each subarray. The measurement found that the mentioned junction arrays can work at several microwave frequency ranges with an operating margin higher than 1.5 mA. Moreover, the circuit can produce intrinsically stable dc voltages from –2 to +2 V and generate stepwise-approximated ac voltages.

IEEE Transactions on Applied Superconductivity•Nov 4, 2022•6 citations

Development of a Quantum AC Voltage Standard Based on Externally Shunted Josephson Arrays

J. Nissilä, Kari Ojasalo, A. Kemppinen +4 more

An AC-voltage standard operating at 1 V level at 1 kHz based on nonhysteretic Josephson junction arrays (JJA) is under development. The electronics connected to the array is now sufficiently fast and noiseless when aiming at a 1-ppm accuracy. Some preliminary results and the current setup and status are reported

Conference on Precision Electromagnetic Measurements•Jun 1, 2004•2 citations
We have developed a programmable Josephson voltage standard based on an array of superconductor–insulator–superconductor junctions. The junctions are damped by an external frequency-dependent shunt circuit, which allows operation at Shapiro steps with n>1. We derive optimization criteria for the design parameters for a fast and stable array with low power consumption. An array able to generate 1.0 VRMS ac voltage signal with sub-ppm accuracy is experimentally demonstrated. Theoretically it is also shown that a fast programmable 10 V array can be realized.
We present experimental results on new programmable Josephson voltage standards based on frequency dependently damped superconductor-insulator-superconductor (SIS) junctions. We introduce a design able to generate two independent floating voltages up to 1.5 V using a microwave frequency of 70 GHz. The array is developed for dc and ac voltage and impedance metrology. The design is optimized in terms of speed, power consumption, and stability. Stimulated power generation is shown to affect the performance of long SIS arrays. The collective dynamics of Josephson junctions is analyzed and a boundary condition for the design of long arrays is derived.
A programmable dc voltage standard for output voltages of up to 10 V has been realized. The series arrays, consisting of about 69120 overdamped superconductor/insulator/normal metal/insulator/superconductor (SINIS) Josephson junctions, have been fabricated using the reliable Nb-Al/Al/sub 2/O/sub 3/ technology. The arrays can be operated in conventional Josephson voltage standards at microwave frequencies from 70 GHz to 75 GHz. Steps of constant voltage are observed at very low microwave power levels, since the major part of the microwave power is generated by the junctions themselves. The operation of the arrays and the formation of Shapiro steps are discussed.
Programmable Josephson voltage standards for output voltages up to 10 V have been realized. Binary-divided series arrays consisting of 69 632 overdamped SINIS Josephson junctions have been fabricated using reliable Nb-Al/Al2O3technology (S: superconductor, I: insulator, N: normal metal). Series arrays of about 1000 SNS Josephson junctions were realized as lumped arrays for applications in the Josephson arbitrary waveform synthesizer (JAWS). We suggest a novel scheme for combining the higher voltages generated by the binary-divided arrays with the frequency spectral characteristics of the JAWS, in order to optimize the frequency spectrum of the generated ac voltages
This article proposes a balanced segmentation scheme to improve the microwave transmission and develops a 2-V programmable Josephson junction array using double-stacked superconductor-normal-metal-superconductor Josephson junctions. The junction numbers of the sub-Josephson arrays are divided into a ternary sequence. The least significant bit is one stack or two junctions. In order to characterize the chip with many subarrays, an automatic measurement system with self-made multichannel current sources was established. It can analyze the critical current, the margin of the voltage steps, and the number of junctions in each subarray. The measurement found that the mentioned junction arrays can work at several microwave frequency ranges with an operating margin higher than 1.5 mA. Moreover, the circuit can produce intrinsically stable dc voltages from –2 to +2 V and generate stepwise-approximated ac voltages.