Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Timing jitter of cascade switch superconducting nanowire single photon detectors

Mikkel Ejrnaes, A. Casaburi, Roberto Cristiano, Orlando Quaranta, S. Marchetti, Nadia Martucciello, S. Pagano, Alessandro Gaggero, F. Mattioli, Roberto Leoni, Paul Cavalier, J.C. Villégier

Published Sep 28, 2009• 23 citations
Publisher

Abstract

We investigate the timing jitter in parallel superconducting NbN-nanowire single photon detectors based on a cascade switch mechanism. The measured timing jitter is asymmetric and has an oscillatory dependence on bias current. At the highest bias current the full width at half maximum was 1.5 times larger than an on-chip reference meander NbN nanowire. A physical model of the dynamics occurring during cascade switch is developed, that quantitatively accounts for our observations as a consequence of different nanowire critical currents within the detector.

DOI
10.1063/1.3237172

Related papers

Timing performance of 30-nm-wide superconducting nanowire avalanche photodetectors

Faraz Najafi, Francesco Marsili, Eric A. Dauler +2 more

We investigated the timing jitter of superconducting nanowire avalanche photodetectors (SNAPs, also referred to as cascade-switching superconducting single-photon detectors) based on 30-nm-wide nanowires. At bias currents (IB) near the switching current, SNAPs showed sub-35-ps FWHM Gaussian jitter similar to standard 100-nm-wide superconducting nanowire single-photon detectors. At lower values of IB, the instrument response function (IRF) of the detectors became wider, more asymmetric, and shifted to longer time delays. We could reproduce the experimentally observed IRF time-shift in simulations based on an electrothermal model and explain the effect with a simple physical picture.

arXiv:1203.1079•Applied Physics Letters•Apr 9, 2012•40 citations

Improving the timing jitter of a superconducting nanowire single-photon detection system

Junjie Wu, Lixing You, Sijing Chen +5 more

Low timing jitter is a unique merit of superconducting nanowire single-photon detectors (SNSPDs) for time-correlated applications. Quantitative analysis was performed for the SNSPD system. Aided by an oscilloscope with an optimal signal amplitude, we were able to measure a full width at half-maximum system timing jitter as low as 14.2 ps for a high-switching-current SNSPD using a room-temperature low-noise amplifier. When using a time-correlated single-photon counting module, the system timing jitter was 17.3 ps. The detector's intrinsic timing jitter was estimated at ∼12.0 ps.

Applied Optics•Mar 6, 2017•96 citations

Large Signal Amplitude and Bias Range of Cascade Switch Superconducting Nanowire Single Photon Detectors

Mikkel Ejrnaes, A. Casaburi, Orlando Quaranta +6 more

Cascade switch superconducting nanowire single photon detectors has been fabricated of ultrathin NbN films deposited by DC-magnetron sputtering at room temperature on MgO substrates. Detectors using 4 to 24 nanowires in parallel, having an area coverage of 5times mum2and a filling factor of 40%, have been investigated. Signal amplitudes increase with the number of parallel nanowires and reaches 12.3 mV with a signal noise of 20 muV. The range of bias currents where the detectors emit signal pulses also increase with the number of parallel nanowires and exceeds the nanowire critical current.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•9 citations

Superconducting single photon detectors based on parallel NbN nanowires

Mikkel Ejrnaes, A. Casaburi, S. Pagano +4 more

Ultrathin NbN nanowires is the material of choice for superconducting single photon detectors (SSPD) due to the good efficiency, dark count rate and timing jitter at 1550 nm wavelength obtained. These performance parameters are achieved using nanowires a few nanometers thick and 100 nm wide patterned into a meander shape in order to achieve area coverage. The meander shape effectively makes the SSPD of a single very long nanowire in turn giving it a significant inductance which limits the maximum count rate of the detector. Recently, we demonstrated how one can exploit a cascade switch to the normal state of nanowires connected in parallel to significantly reduce the SSPD inductance and increase the signal amplitude. Here we present how one can configure SSPDs that uses multiple cascade switches to the normal state. We show how this principle can be used to expand the SSPD coverage area with a very limited increase in detector inductance with area. Finally we discuss our first results obtained with SSPD based on the multiple cascade switch principle, showing correct operation, increased operational bias range and increased signal pulse amplitudes.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 29, 2011•0 citations

Vortex-crossing-induced timing jitter of superconducting nanowire single-photon detectors

Hao Wu, Chao Gu, Yuhao Cheng +1 more

We investigate the timing properties of single-photon-triggered vortex (or anti-vortex) crossing in a current-biased superconducting nanowire and find that the time delays caused in the vortex-crossing process vary with the transverse positions on the nanowire where the photons are absorbed. The position-dependent time delays indicate that the vortex-crossing process induces timing jitter of a superconducting nanowire single-photon detector (SNSPD). The magnitude of this timing jitter further depends on various parameters, including the polarization of the incident photon, the bias current, and the width of the nanowire. This vortex-crossing-induced timing jitter might represent the lower bound of the timing jitter of the SNSPD and fundamentally limit its time-resolving capability.

Applied Physics Letters•Aug 7, 2017•31 citations

Superconducting single photon detectors based on multiple cascade switches of parallel NbN nanowires

Roberto Cristiano, Mikkel Ejrnaes, A. Casaburi +4 more

Ultrathin NbN nanowires is the material of choice for superconducting single photon detectors (SSPD) due to the good efficiency, dark count rate and timing jitter at 1550 nm wavelength obtained. These performance parameters are achieved using nanowires a few nanometers thick and 100 nm wide patterned into a meander shape in order to achieve area coverage. The meander shape effectively makes the SSPD of a single very long nanowire in turn giving it a significant inductance which limits the maximum count rate of the detector. Recently, we demonstrated how one can exploit a cascade switch to the normal state of nanowires connected in parallel to significantly reduce the SSPD inductance and increase the signal amplitude. Here we present how one can configure SSPDs that uses multiple cascade switches to the normal state. We show how this principle can be used to expand the SSPD coverage area with a very limited increase in detector inductance with area. Finally we discuss our first results obtained with SSPD based on the multiple cascade switch principle, showing correct operation.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 30, 2011•2 citations
We investigate the timing jitter in parallel superconducting NbN-nanowire single photon detectors based on a cascade switch mechanism. The measured timing jitter is asymmetric and has an oscillatory dependence on bias current. At the highest bias current the full width at half maximum was 1.5 times larger than an on-chip reference meander NbN nanowire. A physical model of the dynamics occurring during cascade switch is developed, that quantitatively accounts for our observations as a consequence of different nanowire critical currents within the detector.
We investigated the timing jitter of superconducting nanowire avalanche photodetectors (SNAPs, also referred to as cascade-switching superconducting single-photon detectors) based on 30-nm-wide nanowires. At bias currents (IB) near the switching current, SNAPs showed sub-35-ps FWHM Gaussian jitter similar to standard 100-nm-wide superconducting nanowire single-photon detectors. At lower values of IB, the instrument response function (IRF) of the detectors became wider, more asymmetric, and shifted to longer time delays. We could reproduce the experimentally observed IRF time-shift in simulations based on an electrothermal model and explain the effect with a simple physical picture.
Low timing jitter is a unique merit of superconducting nanowire single-photon detectors (SNSPDs) for time-correlated applications. Quantitative analysis was performed for the SNSPD system. Aided by an oscilloscope with an optimal signal amplitude, we were able to measure a full width at half-maximum system timing jitter as low as 14.2 ps for a high-switching-current SNSPD using a room-temperature low-noise amplifier. When using a time-correlated single-photon counting module, the system timing jitter was 17.3 ps. The detector's intrinsic timing jitter was estimated at ∼12.0 ps.
Cascade switch superconducting nanowire single photon detectors has been fabricated of ultrathin NbN films deposited by DC-magnetron sputtering at room temperature on MgO substrates. Detectors using 4 to 24 nanowires in parallel, having an area coverage of 5times mum2and a filling factor of 40%, have been investigated. Signal amplitudes increase with the number of parallel nanowires and reaches 12.3 mV with a signal noise of 20 muV. The range of bias currents where the detectors emit signal pulses also increase with the number of parallel nanowires and exceeds the nanowire critical current.
Ultrathin NbN nanowires is the material of choice for superconducting single photon detectors (SSPD) due to the good efficiency, dark count rate and timing jitter at 1550 nm wavelength obtained. These performance parameters are achieved using nanowires a few nanometers thick and 100 nm wide patterned into a meander shape in order to achieve area coverage. The meander shape effectively makes the SSPD of a single very long nanowire in turn giving it a significant inductance which limits the maximum count rate of the detector. Recently, we demonstrated how one can exploit a cascade switch to the normal state of nanowires connected in parallel to significantly reduce the SSPD inductance and increase the signal amplitude. Here we present how one can configure SSPDs that uses multiple cascade switches to the normal state. We show how this principle can be used to expand the SSPD coverage area with a very limited increase in detector inductance with area. Finally we discuss our first results obtained with SSPD based on the multiple cascade switch principle, showing correct operation, increased operational bias range and increased signal pulse amplitudes.
We investigate the timing properties of single-photon-triggered vortex (or anti-vortex) crossing in a current-biased superconducting nanowire and find that the time delays caused in the vortex-crossing process vary with the transverse positions on the nanowire where the photons are absorbed. The position-dependent time delays indicate that the vortex-crossing process induces timing jitter of a superconducting nanowire single-photon detector (SNSPD). The magnitude of this timing jitter further depends on various parameters, including the polarization of the incident photon, the bias current, and the width of the nanowire. This vortex-crossing-induced timing jitter might represent the lower bound of the timing jitter of the SNSPD and fundamentally limit its time-resolving capability.
Ultrathin NbN nanowires is the material of choice for superconducting single photon detectors (SSPD) due to the good efficiency, dark count rate and timing jitter at 1550 nm wavelength obtained. These performance parameters are achieved using nanowires a few nanometers thick and 100 nm wide patterned into a meander shape in order to achieve area coverage. The meander shape effectively makes the SSPD of a single very long nanowire in turn giving it a significant inductance which limits the maximum count rate of the detector. Recently, we demonstrated how one can exploit a cascade switch to the normal state of nanowires connected in parallel to significantly reduce the SSPD inductance and increase the signal amplitude. Here we present how one can configure SSPDs that uses multiple cascade switches to the normal state. We show how this principle can be used to expand the SSPD coverage area with a very limited increase in detector inductance with area. Finally we discuss our first results obtained with SSPD based on the multiple cascade switch principle, showing correct operation.