Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Performance and Uniformity of Mass-Produced SIS Mixers for ALMA Band 8 Receiver Cartridges

Tomonori Tamura, Takashi Noguchi, Yutaro Sekímoto, Wenlei Shan, Naohisa Sato, Yoshizo Iizuka, Kazuyoshi Kumagai, Yasuaki Niizeki, Mikio Iwakuni, Tetsuya Ito

Published Nov 10, 2014• 6 citations
Publisher

Abstract

We developed SIS mixers for Atacama large millimeter/submillimeter array (ALMA) Band 8 (385-500 GHz) receiver cartridges and evaluated their performance. DC IV curves of the SIS mixers showed small leakage current at the high current density. The current density and quality factor (Rsg/Rn) of the Band 8 SIS junction were 13 kA/cm2and approximately 20, respectively. Double-sideband noise temperature of the 266 SIS mixers was 92.8 K at 4.0 K bath temperature on the average from 385 to 500 GHz with a standard deviation of 7.0%. A couple of sideband-separating (2SB) mixers for dual polarizations were used in the Band 8 receiver cartridge. The 73 receivers have met ALMA specifications of the noise temperature. Single-sideband noise temperature and image rejection ratio of the receivers were 139.5 K and 20.5 dB on the average from 385 to 500 GHz, respectively. These test results of the receivers indicate high quality and uniformity of the 2SB mixers.

DOI
10.1109/tasc.2014.2364223

Related papers

Performance of the First ALMA Band 5 Production Cartridge

Bhushan Billade, Olle Nyström, Denis Meledin +9 more

We present performance of the first ALMA Band 5 production cartridge, covering frequencies from 163 to 211 GHz. Atacama Large Millimeter/sub-millimeter Array (ALMA) Band 5 is a dual polarization, sideband separation (2SB) receiver based on all Niobium (Nb) superconductor–insulator–superconductor (SIS) tunnel junction mixers, providing 16 GHz of instantaneous RF bandwidth for astronomy observations. The 2SB mixer for each polarization employs a quadrature configuration. The sideband separation occurs at the output of the IF hybrid that has integrated bias-T for biasing the mixers, and is produced using superconducting thin-film technology. Experimental verification of the Band 5 cold cartridge performed together with warm cartridge assembly, confirms that the system noise temperature is below 45 K over most of the RF band, which is less than 5 photon noise (5 hf/k). This is to our knowledge, the best results reported at these frequencies. The measurement of the sideband rejection indicates that the sideband rejection is better than 10 dB over 90% of the observational band.

IEEE Transactions on Terahertz Science and Technology•Feb 21, 2012•55 citations

Design and performance of mass-produced sideband separating SIS mixers for ALMA band 4 receivers

Takafumi Kojima, Koichi Kuroiwa, Toshikazu Takahashi +4 more

Abstract We have designed and mass-produced low-noise sideband separating superconductor–insulator–superconductor (SIS) mixers for the Atacama Large Millimeter/submillimeter Array (ALMA) band 4 over the frequency range of 125–163 GHz. An integrated design was adopted for the band 4 sideband separating (2SB) mixer block because of the advantages it offers in terms of compactness, reduced testing time and lower cost. The mixer chip was designed to be robust for handling errors to avoid performance degradation caused by generation of the higher order mode in the mixer chip slot. Detailed analyses revealed its robustness and ability to ensure mass production of the 2SB mixers. Using the robust mixer design in addition to well-established waveguide technologies, all of the 2SB mixers met ALMA specifications for noise temperature and image rejection ratio.

Superconductor Science and Technology•Jul 30, 2015•3 citations

Development of the ALMA Band-3 and Band-6 Sideband-Separating SIS Mixers

Anthony R. Kerr, Shing-Kuo Pan, Stephane M. X. Claude +4 more

As the Atacama Large Millimeter/submillimeter Array (ALMA) nears completion, 73 dual-polarization receivers have been delivered for each of Bands 3 (84-116 GHz) and 6 (211-275 GHz). The receivers use sideband-separating superconducting Nb/Al-AlOx/Nb tunnel-junction (SIS) mixers, developed for ALMA to suppress atmospheric noise in the image band. The mixers were designed taking into account dynamic range, input return loss, and signal-to-image conversion (which can be significant in SIS mixers). Typical SSB receiver noise temperatures in Bands 3 and 6 are 30 and 60 K, respectively, and the image rejection is typically 15 dB.

IEEE Transactions on Terahertz Science and Technology•Feb 13, 2014•63 citations

Performance of the first ALMA Band 5 production cartridge

Bhushan Billade, Olle Nyström, Denis Meledin +13 more

We present performance of the first ALMA Band 5 production cartridge, covering RF frequencies from 163 GHz to 211 GHz. ALMA Band 5 is a dual polarization, sideband separation (2SB) receiver based on all Niobium (Nb) SuperconductorInsulator-Superconductor (SIS) tunnel junction mixer, providing 16 GHz of instantaneous RF bandwidth for the astronomy observations. The 2SB mixer for each polarization employs a quadrature layout. The sideband separation occurs at the output of the IF hybrid that has integrated bias-T for biasing the mixers, and is produced using superconducting thin film technology. Experimental verification of the Band 5 cold cartridge performed together with warm cartridge assembly, confirms the system noise temperature below 45 K, less than five quantum noise (5 hf/k) over most of the RF band, which is to our knowledge, the best results at these frequencies. The measurement of the sideband rejection indicates that the sideband rejection better than 10 dB over 90% of the observational band.

•Jan 1, 2011•0 citations

A 385-500 GHz Low Noise Superconductor-Insulator- Superconductor Mixer for ALMA Band 8

Wenlei Shan

We report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm(2) and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. A parallel-connected twin-junction (PCTJ) is designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it easy to match the low-impedance PCTJ over a wide frequency band. The RF embedding impedance is retrieved by fitting the measured pumped I-V curves to confirm good matching between PCTJ and signal source. We demonstrate here a minimum double-sideband receiver noise temperature of 3 times of quantum limits for an intermediate-frequency range of 4-8 GHz. The mixers were measured in band 8 cartridge with a sideband separation scheme. Single-sideband receiver noise below ALMA specification was achieved over the whole band.

IEICE Transactions on Electronics•Feb 1, 2006•11 citations

An SIS-based sideband-separating heterodyne mixer optimized for the 600 to 720 GHz band

Fausto Patricio Mena, J. Kooi, Andrey M. Baryshev +4 more

The Atacama Large Millimeter Array (ALMA) is the largest radio astronomical enterprise ever proposed. When completed, each of its 64 constituting radio-telescopes will be able to hold 10 heterodyne receivers covering the spectroscopic windows allowed by the atmospheric transmission at the construction site, the altiplanos of the northern Chilean Andes. In contrast to the sideband-separating (2SB) receivers being developed at low frequencies, double-side-band (DSB) receivers are being developed for the highest two spectroscopic windows (bands 9 and 10). Despite of the well known advantages of 2SB mixers over their DSB counterparts, they have not been implemented at the highest-frequency bands as the involved dimensions for some of the radio frequency components are prohibitory small. However, the current state-of-the-art micromachining technology has proved that the structures necessary for this development are attainable. Here we report the design, modeling, realization, and characterization of a 2SB mixer for band 9 of ALMA (600 to 720 GHz). At the heart of the mixer, two superconductor-insulator-superconductor (SIS) junctions are used as mixing elements. The constructed instrument presents an excellent performance as shown by two important figures of merit: noise temperature of the system and side band ratio, both of them within ALMA specifications.

Journal of Physics Conference Series•Feb 1, 2008•3 citations
We developed SIS mixers for Atacama large millimeter/submillimeter array (ALMA) Band 8 (385-500 GHz) receiver cartridges and evaluated their performance. DC IV curves of the SIS mixers showed small leakage current at the high current density. The current density and quality factor (Rsg/Rn) of the Band 8 SIS junction were 13 kA/cm2and approximately 20, respectively. Double-sideband noise temperature of the 266 SIS mixers was 92.8 K at 4.0 K bath temperature on the average from 385 to 500 GHz with a standard deviation of 7.0%. A couple of sideband-separating (2SB) mixers for dual polarizations were used in the Band 8 receiver cartridge. The 73 receivers have met ALMA specifications of the noise temperature. Single-sideband noise temperature and image rejection ratio of the receivers were 139.5 K and 20.5 dB on the average from 385 to 500 GHz, respectively. These test results of the receivers indicate high quality and uniformity of the 2SB mixers.
We present performance of the first ALMA Band 5 production cartridge, covering frequencies from 163 to 211 GHz. Atacama Large Millimeter/sub-millimeter Array (ALMA) Band 5 is a dual polarization, sideband separation (2SB) receiver based on all Niobium (Nb) superconductor–insulator–superconductor (SIS) tunnel junction mixers, providing 16 GHz of instantaneous RF bandwidth for astronomy observations. The 2SB mixer for each polarization employs a quadrature configuration. The sideband separation occurs at the output of the IF hybrid that has integrated bias-T for biasing the mixers, and is produced using superconducting thin-film technology. Experimental verification of the Band 5 cold cartridge performed together with warm cartridge assembly, confirms that the system noise temperature is below 45 K over most of the RF band, which is less than 5 photon noise (5 hf/k). This is to our knowledge, the best results reported at these frequencies. The measurement of the sideband rejection indicates that the sideband rejection is better than 10 dB over 90% of the observational band.
Abstract We have designed and mass-produced low-noise sideband separating superconductor–insulator–superconductor (SIS) mixers for the Atacama Large Millimeter/submillimeter Array (ALMA) band 4 over the frequency range of 125–163 GHz. An integrated design was adopted for the band 4 sideband separating (2SB) mixer block because of the advantages it offers in terms of compactness, reduced testing time and lower cost. The mixer chip was designed to be robust for handling errors to avoid performance degradation caused by generation of the higher order mode in the mixer chip slot. Detailed analyses revealed its robustness and ability to ensure mass production of the 2SB mixers. Using the robust mixer design in addition to well-established waveguide technologies, all of the 2SB mixers met ALMA specifications for noise temperature and image rejection ratio.
As the Atacama Large Millimeter/submillimeter Array (ALMA) nears completion, 73 dual-polarization receivers have been delivered for each of Bands 3 (84-116 GHz) and 6 (211-275 GHz). The receivers use sideband-separating superconducting Nb/Al-AlOx/Nb tunnel-junction (SIS) mixers, developed for ALMA to suppress atmospheric noise in the image band. The mixers were designed taking into account dynamic range, input return loss, and signal-to-image conversion (which can be significant in SIS mixers). Typical SSB receiver noise temperatures in Bands 3 and 6 are 30 and 60 K, respectively, and the image rejection is typically 15 dB.
We present performance of the first ALMA Band 5 production cartridge, covering RF frequencies from 163 GHz to 211 GHz. ALMA Band 5 is a dual polarization, sideband separation (2SB) receiver based on all Niobium (Nb) SuperconductorInsulator-Superconductor (SIS) tunnel junction mixer, providing 16 GHz of instantaneous RF bandwidth for the astronomy observations. The 2SB mixer for each polarization employs a quadrature layout. The sideband separation occurs at the output of the IF hybrid that has integrated bias-T for biasing the mixers, and is produced using superconducting thin film technology. Experimental verification of the Band 5 cold cartridge performed together with warm cartridge assembly, confirms the system noise temperature below 45 K, less than five quantum noise (5 hf/k) over most of the RF band, which is to our knowledge, the best results at these frequencies. The measurement of the sideband rejection indicates that the sideband rejection better than 10 dB over 90% of the observational band.
We report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm(2) and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. A parallel-connected twin-junction (PCTJ) is designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it easy to match the low-impedance PCTJ over a wide frequency band. The RF embedding impedance is retrieved by fitting the measured pumped I-V curves to confirm good matching between PCTJ and signal source. We demonstrate here a minimum double-sideband receiver noise temperature of 3 times of quantum limits for an intermediate-frequency range of 4-8 GHz. The mixers were measured in band 8 cartridge with a sideband separation scheme. Single-sideband receiver noise below ALMA specification was achieved over the whole band.
The Atacama Large Millimeter Array (ALMA) is the largest radio astronomical enterprise ever proposed. When completed, each of its 64 constituting radio-telescopes will be able to hold 10 heterodyne receivers covering the spectroscopic windows allowed by the atmospheric transmission at the construction site, the altiplanos of the northern Chilean Andes. In contrast to the sideband-separating (2SB) receivers being developed at low frequencies, double-side-band (DSB) receivers are being developed for the highest two spectroscopic windows (bands 9 and 10). Despite of the well known advantages of 2SB mixers over their DSB counterparts, they have not been implemented at the highest-frequency bands as the involved dimensions for some of the radio frequency components are prohibitory small. However, the current state-of-the-art micromachining technology has proved that the structures necessary for this development are attainable. Here we report the design, modeling, realization, and characterization of a 2SB mixer for band 9 of ALMA (600 to 720 GHz). At the heart of the mixer, two superconductor-insulator-superconductor (SIS) junctions are used as mixing elements. The constructed instrument presents an excellent performance as shown by two important figures of merit: noise temperature of the system and side band ratio, both of them within ALMA specifications.