Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

High-resolution single-mode fiber-optic distributed Raman sensor for absolute temperature measurement using superconducting nanowire single-photon detectors

Michael G. Tanner, Shellee D. Dyer, Burm Baek, Robert H. Hadfield, Sae Woo Nam

Published Nov 14, 2011• 102 citations
Publisher

Abstract

We demonstrate a distributed fiber Raman sensor for absolute temperature measurement with spatial resolution on the order of 1 cm at 1550 nm wavelength in a single-mode fiber using superconducting nanowire single-photon detectors. Rapid measurements are shown, with less than 60 s integration period, allowing the demonstration of temperature evolution in an optical fiber recorded at over 100 resolvable, 1.2 cm spaced positions along the fiber simultaneously. This distributed sensor has potential application as a primary reference standard, in which high-accuracy, high-spatial-resolution temperature measurements can be obtained without the need for a separate temperature calibration standard.

DOI
10.1063/1.3656702

Related papers

Analysis of a distributed fiber-optic temperature sensor using single-photon detectors

Shellee D. Dyer, Michael G. Tanner, Burm Baek +2 more

We demonstrate a high-accuracy distributed fiber-optic temperature sensor using superconducting nanowire single-photon detectors and single-photon counting techniques. Our demonstration uses inexpensive single-mode fiber at standard telecommunications wavelengths as the sensing fiber, which enables extremely low-loss experiments and compatibility with existing fiber networks. We show that the uncertainty of the temperature measurement decreases with longer integration periods, but is ultimately limited by the calibration uncertainty. Temperature uncertainty on the order of 3 K is possible with spatial resolution of the order of 1 cm and integration period as small as 60 seconds. Also, we show that the measurement is subject to systematic uncertainties, such as polarization fading, which can be reduced with a polarization diversity receiver.

arXiv:1111.4178•Optics Express•Jan 30, 2012•53 citations

Electrical thermography via centimetre-scale fiber-based distributed temperature sensing

Victor Cochet, Axel Faccio, Georgios Stoikos +4 more

We present a Raman-based Distributed Temperature Sensor (RDTS) with centimetre-scale resolution for thermographic analysis of electronic circuits. Temperature is measured along a single-mode fiber routed across a custom printed circuit board (PCB) with 1 cm$^2$ heating elements, using optical time-domain reflectometry of Raman signals detected by superconducting nanowire single-photon detectors (SNSPDs). This approach enables two-dimensional thermal mapping of the PCB under heating configurations with multiple hotspots. A spatial resolution of 3 cm and a temperature accuracy of 2 °C are achieved with an integration time of 5 minutes. Thermography can be performed down to 77 K, revealing that the PCB thermal resistance decreases by nearly an order of magnitude compared to room temperature, due to enhanced convective cooling in liquid nitrogen. These results establish centimetre-scale RDTS as a robust technique for real-time, spatially resolved thermography of electronic circuits, particularly in regimes where infrared imaging is ineffective, such as at low temperatures or within volumetric electronic architectures.

quant-pharXiv:2511.11184•Nov 17, 2025

Cryogenic temperature 3D mapping via a distributed temperature sensor with centimeter resolution

Luca Corradin, Gabriel Thiebaut, Gaëtan Gras +3 more

We conduct 3D mapping of cryogenic temperatures via a Raman-based distributed temperature sensor, employing standard telecom single-mode fibers and polarization-independent superconducting nanowire single photon detectors (SNSPDs). By coiling a test fiber around various stages of a liquid helium cooled cryostat, our device demonstrates a lower temperature sensing limit of (48 ± 2) K, below the nitrogen boiling point. This achievement is made possible by the low dark count rates of SNSPDs, as validated by theoretical simulations. Furthermore, we utilize our device to map cryogenic temperatures on the 350 cm 2 surface of a specially designed hollow cylindrical aluminum sample, accommodating approximately 2 m of standard single-mode optical fiber. During nitrogen cooling, we monitor the temporal evolution of the spatially dependent temperature gradient on the metallic sample with a temporal sampling down to one minute. Fiber-based distributed temperature sensing with centimetric spatial resolution can be effectively applied for 3D mapping at cryogenic temperatures of superconducting, quantum computing and aerospace instrumentation.

Optics Express•Apr 29, 2024•4 citations

Multimode-fiber-coupled superconducting nanowire single-photon detectors with high detection efficiency and time resolution

Jin Chang, Iman Esmaeil Zadeh, Johannes W. N. Los +7 more

In the past decade, superconducting nanowire single-photon detectors (SNSPDs) have gradually become an indispensable part of any demanding quantum optics experiment. Until now, most SNSPDs have been coupled to single-mode fibers. SNSPDs coupled to multimode fibers have shown promising efficiencies but have yet to achieve high time resolution. For a number of applications ranging from quantum nano-photonics to bio-optics, high efficiency and high time resolution are desired at the same time. In this paper, we demonstrate the role of polarization on the efficiency of multimode-fiber-coupled detectors and fabricated high-performance 20 µm, 25 µm, and 50 µm diameter detectors targeted for visible, near-infrared, and telecom wavelengths. A custom-built setup was used to simulate realistic experiments with randomized modes in the fiber. We achieved over 80% system efficiency and $ {\lt} {20}\;{\rm ps}$<20ps timing jitter for 20 µm SNSPDs. Also, we realized 70% system efficiency and $ {\lt} {20}\;{\rm ps}$<20ps timing jitter for 50 µm SNSPDs. The high-efficiency multimode-fiber-coupled SNSPDs with unparalleled time resolution will benefit various quantum optics experiments and applications in the future.

arXiv:1908.06205•Applied Optics•Dec 10, 2019•34 citations

Superconducting nanowire single-photon detectors with 98% system detection efficiency at 1550 nm

Dileep V. Reddy, Robert R. Nerem, Sae Woo Nam +2 more

Superconducting nanowire single-photon detectors (SNSPDs) are an enabling technology for myriad quantum-optics experiments that require high-efficiency detection, large count rates, and precise timing resolution. The system detection efficiencies (SDEs) for fiber-coupled SNSPDs have fallen short of theoretical predictions of near unity by at least 7%, with the discrepancy being attributed to scattering, material absorption, and other SNSPD dynamics. We optimize the design and fabrication of an all-dielectric layered stack and fiber coupling package in order to achieve 98.0 ± 0.5 % SDE, measured for single-mode-fiber guided photons derived from a highly attenuated 1550 nm continuous-wave laser. This enforces a smaller bound on the scattering and absorption losses in such systems and opens the use of SNSPDs for scenarios that demand high-SDE for throughput and fidelity.

Optica•Oct 28, 2020•407 citations

Superconducting nanowire single-photon detectors at a wavelength of 940 nm

W. J. Zhang, Hao Li, Lixing You +9 more

We develop single-photon detectors comprising single-mode fiber-coupled superconducting nanowires, with high system detection efficiencies at a wavelength of 940 nm. The detector comprises a 6.5-nm-thick, 110-nm-wide NbN nanowire meander fabricated onto a Si substrate with a distributed Bragg reflector for enhancing the optical absorptance. We demonstrate that, via the design of a low filling factor (1/3) and active area (Φ = 10 μm), the system reaches a detection efficiency of ∼60% with a dark count rate of 10 Hz, a recovery time <12 ns, and a timing jitter of ∼50 ps.

arXiv:1506.07921•AIP Advances•Jun 1, 2015•7 citations
We demonstrate a distributed fiber Raman sensor for absolute temperature measurement with spatial resolution on the order of 1 cm at 1550 nm wavelength in a single-mode fiber using superconducting nanowire single-photon detectors. Rapid measurements are shown, with less than 60 s integration period, allowing the demonstration of temperature evolution in an optical fiber recorded at over 100 resolvable, 1.2 cm spaced positions along the fiber simultaneously. This distributed sensor has potential application as a primary reference standard, in which high-accuracy, high-spatial-resolution temperature measurements can be obtained without the need for a separate temperature calibration standard.
We demonstrate a high-accuracy distributed fiber-optic temperature sensor using superconducting nanowire single-photon detectors and single-photon counting techniques. Our demonstration uses inexpensive single-mode fiber at standard telecommunications wavelengths as the sensing fiber, which enables extremely low-loss experiments and compatibility with existing fiber networks. We show that the uncertainty of the temperature measurement decreases with longer integration periods, but is ultimately limited by the calibration uncertainty. Temperature uncertainty on the order of 3 K is possible with spatial resolution of the order of 1 cm and integration period as small as 60 seconds. Also, we show that the measurement is subject to systematic uncertainties, such as polarization fading, which can be reduced with a polarization diversity receiver.
We present a Raman-based Distributed Temperature Sensor (RDTS) with centimetre-scale resolution for thermographic analysis of electronic circuits. Temperature is measured along a single-mode fiber routed across a custom printed circuit board (PCB) with 1 cm2^22 heating elements, using optical time-domain reflectometry of Raman signals detected by superconducting nanowire single-photon detectors (SNSPDs). This approach enables two-dimensional thermal mapping of the PCB under heating configurations with multiple hotspots. A spatial resolution of 3 cm and a temperature accuracy of 2 °C are achieved with an integration time of 5 minutes. Thermography can be performed down to 77 K, revealing that the PCB thermal resistance decreases by nearly an order of magnitude compared to room temperature, due to enhanced convective cooling in liquid nitrogen. These results establish centimetre-scale RDTS as a robust technique for real-time, spatially resolved thermography of electronic circuits, particularly in regimes where infrared imaging is ineffective, such as at low temperatures or within volumetric electronic architectures.
We conduct 3D mapping of cryogenic temperatures via a Raman-based distributed temperature sensor, employing standard telecom single-mode fibers and polarization-independent superconducting nanowire single photon detectors (SNSPDs). By coiling a test fiber around various stages of a liquid helium cooled cryostat, our device demonstrates a lower temperature sensing limit of (48 ± 2) K, below the nitrogen boiling point. This achievement is made possible by the low dark count rates of SNSPDs, as validated by theoretical simulations. Furthermore, we utilize our device to map cryogenic temperatures on the 350 cm 2 surface of a specially designed hollow cylindrical aluminum sample, accommodating approximately 2 m of standard single-mode optical fiber. During nitrogen cooling, we monitor the temporal evolution of the spatially dependent temperature gradient on the metallic sample with a temporal sampling down to one minute. Fiber-based distributed temperature sensing with centimetric spatial resolution can be effectively applied for 3D mapping at cryogenic temperatures of superconducting, quantum computing and aerospace instrumentation.
In the past decade, superconducting nanowire single-photon detectors (SNSPDs) have gradually become an indispensable part of any demanding quantum optics experiment. Until now, most SNSPDs have been coupled to single-mode fibers. SNSPDs coupled to multimode fibers have shown promising efficiencies but have yet to achieve high time resolution. For a number of applications ranging from quantum nano-photonics to bio-optics, high efficiency and high time resolution are desired at the same time. In this paper, we demonstrate the role of polarization on the efficiency of multimode-fiber-coupled detectors and fabricated high-performance 20 µm, 25 µm, and 50 µm diameter detectors targeted for visible, near-infrared, and telecom wavelengths. A custom-built setup was used to simulate realistic experiments with randomized modes in the fiber. We achieved over 80% system efficiency and $ {\lt} {20}\;{\rm ps}$<20ps timing jitter for 20 µm SNSPDs. Also, we realized 70% system efficiency and $ {\lt} {20}\;{\rm ps}$<20ps timing jitter for 50 µm SNSPDs. The high-efficiency multimode-fiber-coupled SNSPDs with unparalleled time resolution will benefit various quantum optics experiments and applications in the future.
Superconducting nanowire single-photon detectors (SNSPDs) are an enabling technology for myriad quantum-optics experiments that require high-efficiency detection, large count rates, and precise timing resolution. The system detection efficiencies (SDEs) for fiber-coupled SNSPDs have fallen short of theoretical predictions of near unity by at least 7%, with the discrepancy being attributed to scattering, material absorption, and other SNSPD dynamics. We optimize the design and fabrication of an all-dielectric layered stack and fiber coupling package in order to achieve 98.0 ± 0.5 % SDE, measured for single-mode-fiber guided photons derived from a highly attenuated 1550 nm continuous-wave laser. This enforces a smaller bound on the scattering and absorption losses in such systems and opens the use of SNSPDs for scenarios that demand high-SDE for throughput and fidelity.
We develop single-photon detectors comprising single-mode fiber-coupled superconducting nanowires, with high system detection efficiencies at a wavelength of 940 nm. The detector comprises a 6.5-nm-thick, 110-nm-wide NbN nanowire meander fabricated onto a Si substrate with a distributed Bragg reflector for enhancing the optical absorptance. We demonstrate that, via the design of a low filling factor (1/3) and active area (Φ = 10 μm), the system reaches a detection efficiency of ∼60% with a dark count rate of 10 Hz, a recovery time <12 ns, and a timing jitter of ∼50 ps.