Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Japanese Journal of Applied Physics

High-Quality Nb/AlOx-Al/Nb Josephson Junctions with Gap Voltage of 2.95 mV

Masanobu Kusünoki, Hirotake Yamamori, Akira Fujimaki, Yoshiaki Takai, Hisao Hayakawa

Published Nov 1, 1993• 3 citations
Publisher

Abstract

The dependence of the gap voltage on impurities in Nb films is studied. The gap voltage is determined by the number of impurities included in the films. The impurities arise from the residual gas in the sputtering chamber before the deposition of Nb films. By reducing the impurities in the films, we obtain high-quality Nb/AlO x -Al/Nb Josephson junctions having the gap voltage of 2.95 mV which is close to that estimated from the energy gap of Nb bulk at 4.2 K. In addition, the use of a thin Al layer is also an important factor in obtaining excellent current-voltage characteristics.

DOI
10.1143/jjap.32.l1609

Related papers

Nb/AlOx/Nb Josephson Tunnel Junctions Using Electron Beam Evaporation

Atsuki Inoue, Akiyoshi Nakayama, Yoichi Okabe

Niobium/aluminum-oxide/niobium Josephson tunnel junctions have been fabricated using electron beam evaporation to form all-metal films in a high vacuum system. A quality factor, V m (the product of the maximum dc Josephson current and the subgap resistance defined at 2 mV) between 36–37 mV, has been obtained for the best junctions of a 6 nm-thick Al layer by cooling down the surface of the base electrode for 100 minutes under a high background pressure, before the deposition of aluminum, after the formation of the base niobium electrode. An array of 80 series-connected junctions has also been fabricated using the selective niobium anodization process and the planarization process. The current-voltage characteristics of the array showed a standard deviation of the maximum dc Josephson current of 3.3%.

Japanese Journal of Applied Physics•Jul 1, 1988•10 citations

Overdamped NbN Josephson Junctions Based on Nb/AlOx/Nb Trilayer Technology

Takao Iwai, Takashi Aoyama, Ryutaro Oke +3 more

We have fabricated overdamped NbN Josephson junctions based on Nb/AlO x /Nb trilayer technology. The junctions have the structure of NbN/Nb/AlO x /Nb/NbN, where Nb/AlO x /Nb acts as a junction barrier. The overdamped junctions showed a critical current density J c and characteristic voltage as high as 0.44 kA/cm2 and 160 µV at 10 K, respectively. The junction characteristics at 4.2 K were investigated from the viewpoint of their dependence on the film thickness of the Nb layers. The junction uniformity was also evaluated. The standard deviation, 1-σ, was 2.1% for a series of 64 5×5 µm2 junctions at 4.2 K.

Japanese Journal of Applied Physics•Aug 1, 1999•5 citations

Film Stress Influence on Nb/Al-AlO x /Nb Josephson Junctions

Yu Wu, Liliang Ying, Guanqun Li +4 more

Nb/Al-AlOx/Nb Josephson junctions are widely used in superconducting quantum interference devices and rapid single flux quantum (RSFQ) circuits. Very large-scale RSFQ integration often has a strict requirement on wafer-scale junction qualities. In particular, Nb film stress in Nb/Al-AlOx/Nb trilayer based Josephson junctions is a critical factor affecting their qualities. In this work, we develop a multi-step sputtering process to prepare Nb films with different combinations of stress and roughness to investigate the correlation between Nb film stress and junction quality. In particular, this method allows us to prepare Nb films with almost the same roughness but different stress, a key factor to study solely the influence of stress on junction qualities. Our measurements indicate that within a very tight range of film roughness (less than 2 nm), tensile film stress is found to decrease the quality of Nb/Al-AlOx/Nb Josephson junctions and larger film roughness has a positive effect on junction quality. By decreasing the total tensile stress and increasing the film roughness properly, we fabricated Nb/Al-AlOx/Nb Josephson junctions with a high quality factor characterized by Rsg/RN(30 on average). The minimum size of junctions was 1 μm.

IEEE Transactions on Applied Superconductivity•Mar 18, 2019•28 citations

Overdamped Josephson junctions with Nb/AlOx/Al/AlOx/Nb structure for integrated circuit application

Masaaki Maezawa, Akira Shoji

We present characteristics of overdamped Josephson junctions consisting of Nb/AlOx/Al/ AlOx/Nb structures. The junctions were fabricated using a well-developed Nb/AlOx/Nb-junction technology and showed well-defined Josephson characteristics at 4.2 K. The characteristic voltage Vc [the product of the critical current Ic and the effective normal resistance Rn(eff)] of junctions, which determines high-frequency performance of the junction, was in the range of 0.1–0.5 mV, and the critical current density Jc in the range of 102–104 A/cm2. Maximum-to-minimum variations in Ic over a wafer were ±4% for junctions with Vc=0.15 mV and ±13% for junctions with Vc=0.5 mV.

Applied Physics Letters•Jun 30, 1997•67 citations

NbN/AlN/NbN Josephson Junctions on Sapphire for SIS Receiver Applications

Michael Merker, Christian Bohn, Marvin Vollinger +2 more

The most developed integrated receivers for THz radiation nowadays are based on Josephson junction superconductor-insulator-superconductor devices. In this kind of devices, the highest receivable frequency is determined by the energy gap of the superconducting electrodes and limited to approximately 700 GHz in case of Nb/AlOx/Nb multilayers. We have developed a technology for NbN/AlN/NbN Josephson junctions on sapphire substrates which allow operation at frequencies above 1 THz. The trilayers are deposited in situ in a three-chamber dc-magnetron sputtering system at temperatures as high as 775 °C. Each layer is reactively sputtered in an argon and nitrogen atmosphere. By variation of the partial gas pressures and discharge current of the plasma, optimum deposition conditions for the tri-layers were found. So far, gap voltages as high as 5.1 mV at 4.2 K have been achieved which allows the operation frequency of the JJ devices to exceed 1 THz.

arXiv:1612.02713•IEEE Transactions on Applied Superconductivity•Dec 9, 2016•6 citations

Fabrication of all-NbN Josephson tunnel junctions using single crystal NbN films for the base electrodes

Alexandre Shoji

All-NbN Josephson tunnel junctions with sputter-deposited magnesium oxide barriers have been fabricated using single-crystal NbN films for the base electrodes. Fabricated Josephson junctions have shown good tunneling characteristics with large gap voltages (5.6-5.8 mV), narrow gap widths (0.1-0.2 mV, from 30 to 70%), and small subgap leakage currents (V/sub m/=20-30 mV, measured at 3 mV). The results of a measurement of a subgap structure for a fabricated junction suggest that the excess leakage currents of fabricated junctions are due to multiparticle tunneling through locally thin areas in the MgO barriers.

IEEE Transactions on Magnetics•Mar 1, 1991•25 citations
The dependence of the gap voltage on impurities in Nb films is studied. The gap voltage is determined by the number of impurities included in the films. The impurities arise from the residual gas in the sputtering chamber before the deposition of Nb films. By reducing the impurities in the films, we obtain high-quality Nb/AlO x -Al/Nb Josephson junctions having the gap voltage of 2.95 mV which is close to that estimated from the energy gap of Nb bulk at 4.2 K. In addition, the use of a thin Al layer is also an important factor in obtaining excellent current-voltage characteristics.
Niobium/aluminum-oxide/niobium Josephson tunnel junctions have been fabricated using electron beam evaporation to form all-metal films in a high vacuum system. A quality factor, V m (the product of the maximum dc Josephson current and the subgap resistance defined at 2 mV) between 36–37 mV, has been obtained for the best junctions of a 6 nm-thick Al layer by cooling down the surface of the base electrode for 100 minutes under a high background pressure, before the deposition of aluminum, after the formation of the base niobium electrode. An array of 80 series-connected junctions has also been fabricated using the selective niobium anodization process and the planarization process. The current-voltage characteristics of the array showed a standard deviation of the maximum dc Josephson current of 3.3%.
We have fabricated overdamped NbN Josephson junctions based on Nb/AlO x /Nb trilayer technology. The junctions have the structure of NbN/Nb/AlO x /Nb/NbN, where Nb/AlO x /Nb acts as a junction barrier. The overdamped junctions showed a critical current density J c and characteristic voltage as high as 0.44 kA/cm2 and 160 µV at 10 K, respectively. The junction characteristics at 4.2 K were investigated from the viewpoint of their dependence on the film thickness of the Nb layers. The junction uniformity was also evaluated. The standard deviation, 1-σ, was 2.1% for a series of 64 5×5 µm2 junctions at 4.2 K.
Nb/Al-AlOx/Nb Josephson junctions are widely used in superconducting quantum interference devices and rapid single flux quantum (RSFQ) circuits. Very large-scale RSFQ integration often has a strict requirement on wafer-scale junction qualities. In particular, Nb film stress in Nb/Al-AlOx/Nb trilayer based Josephson junctions is a critical factor affecting their qualities. In this work, we develop a multi-step sputtering process to prepare Nb films with different combinations of stress and roughness to investigate the correlation between Nb film stress and junction quality. In particular, this method allows us to prepare Nb films with almost the same roughness but different stress, a key factor to study solely the influence of stress on junction qualities. Our measurements indicate that within a very tight range of film roughness (less than 2 nm), tensile film stress is found to decrease the quality of Nb/Al-AlOx/Nb Josephson junctions and larger film roughness has a positive effect on junction quality. By decreasing the total tensile stress and increasing the film roughness properly, we fabricated Nb/Al-AlOx/Nb Josephson junctions with a high quality factor characterized by Rsg/RN(30 on average). The minimum size of junctions was 1 μm.
We present characteristics of overdamped Josephson junctions consisting of Nb/AlOx/Al/ AlOx/Nb structures. The junctions were fabricated using a well-developed Nb/AlOx/Nb-junction technology and showed well-defined Josephson characteristics at 4.2 K. The characteristic voltage Vc [the product of the critical current Ic and the effective normal resistance Rn(eff)] of junctions, which determines high-frequency performance of the junction, was in the range of 0.1–0.5 mV, and the critical current density Jc in the range of 102–104 A/cm2. Maximum-to-minimum variations in Ic over a wafer were ±4% for junctions with Vc=0.15 mV and ±13% for junctions with Vc=0.5 mV.
The most developed integrated receivers for THz radiation nowadays are based on Josephson junction superconductor-insulator-superconductor devices. In this kind of devices, the highest receivable frequency is determined by the energy gap of the superconducting electrodes and limited to approximately 700 GHz in case of Nb/AlOx/Nb multilayers. We have developed a technology for NbN/AlN/NbN Josephson junctions on sapphire substrates which allow operation at frequencies above 1 THz. The trilayers are deposited in situ in a three-chamber dc-magnetron sputtering system at temperatures as high as 775 °C. Each layer is reactively sputtered in an argon and nitrogen atmosphere. By variation of the partial gas pressures and discharge current of the plasma, optimum deposition conditions for the tri-layers were found. So far, gap voltages as high as 5.1 mV at 4.2 K have been achieved which allows the operation frequency of the JJ devices to exceed 1 THz.
All-NbN Josephson tunnel junctions with sputter-deposited magnesium oxide barriers have been fabricated using single-crystal NbN films for the base electrodes. Fabricated Josephson junctions have shown good tunneling characteristics with large gap voltages (5.6-5.8 mV), narrow gap widths (0.1-0.2 mV, from 30 to 70%), and small subgap leakage currents (V/sub m/=20-30 mV, measured at 3 mV). The results of a measurement of a subgap structure for a fabricated junction suggest that the excess leakage currents of fabricated junctions are due to multiparticle tunneling through locally thin areas in the MgO barriers.