Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

Wide-band operation of quasi-optical distributed superconductor/insulator/superconductor mixers with epitaxial NbN/AlN/NbN junctions

Satoshi Kohjiro, S. V. Shitov, Z Wang, Yoshinori Uzawa, Shigehito Miki, Akira Kawakami, Alexandre Shoji

Published Apr 6, 2004• 2 citations
Publisher

Abstract

For the optimum design of integrated receivers operating above the gap frequency of Nb, we have designed, fabricated and tested NbN-based quasi-optical superconductor/insulator/superconductor (SIS) mixers. The mixer chip incorporates a resonant half-wavelength epitaxial NbN/AlN/NbN junction, a twin-slot antenna and their coupling circuits. We adopted two kinds of coupling circuit between the antenna and the SIS junction: one is an in-phase feed with a length of 95 µm and the other is an anti-phase feed of 30 µm length. It was found that the anti-phase mixer reveals a 3 dB bandwidth of 43% of the centre frequency; the uncorrected double-sideband receiver noise temperature TRX = 691 K at 0.91 THz and TRX = 844 K at 0.80 THz, while 17% and TRX = 1250 K at 0.79 THz for the in-phase version. Possible reasons for this difference are discussed, which could be transmission loss and its robustness with respect to the variation of junction parameters. These experimental results suggest the NbN-based distributed mixer with the anti-phase feed is a better candidate for wide-band integrated receivers operating above 0.7 THz.

DOI
10.1088/0953-2048/17/5/040

Related papers

Performance of all-NbN quasi-optical SIS mixers for the terahertz band

Yoshinori Uzawa, Akira Kawakami, Shigehito Miki +1 more

We have designed, fabricated, and tested terahertz superconductor-insulator-superconductor (SIS) mixers having a self-compensated NbN/AlN/NbN tunnel junction and an epitaxially grown NbN/MgO/NbN microstripline. The junction as a distributed element was 0.8-/spl mu/m wide and 2.4-/spl mu/m long, and its current density was 50 kA/cm/sup 2/. The microstripline consisted of a 200-nm-thick NbN ground plane, a 180-nm-thick MgO insulator, and a 350-nm-thick NbN wiring layer. An investigation of the mixer in our receiver configuration showed flat noise characteristics from 870 to 960 GHz. The lowest receiver noise temperature of about 550 K was obtained at 909 GHz, including a 9-/spl mu/m-thick Mylar beam splitter loss and other optical losses. These characteristics suggest that SIS mixers with self-compensated NbN/AlN/NbN junctions and NbN/MgO/NbN microstriplines are appropriate for used in wideband and low-noise operations at terahertz frequencies.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•21 citations

A submillimetre-wave SIS mixer using NbN/MgO/NbN trilayers grown epitaxially on an MgO substrate

Yoshinori Uzawa, Akira Kawakami, Atsushi SAITO +2 more

We have designed, fabricated and tested a quasi-optical superconductor–insulator–superconductor (SIS) mixer employing distributed NbN/MgO/NbN tunnel junctions and NbN/MgO/NbN microstriplines at submillimetre-wave frequencies. These trilayers were fabricated by dc- and rf-magnetron sputtering on an MgO substrate at ambient temperature so that the NbN and MgO films were grown epitaxially. Our SIS mixer consists of an MgO hyperhemispherical lens with an antireflection cap and a self-complementary log-periodic antenna made of a single-crystal NbN film, on which the distributed SIS junctions and the two-section impedance transformers were mirror-symmetrically placed at the feed point of the antenna. As designed, the junctions are 0.6 μm wide and 15.5 μm long, which is sufficient to absorb the incoming signal along this lossy transmission line, assuming a current density of 10 kA cm −2 . The mixer showed good I – V characteristics, with subgap-to-normal resistance ratios of about 13, although weak-link breaks were observed above the gap voltage. The minimum double side band receiver noise temperature was 334 K at 678 GHz, including the input noise of about 200 K as estimated by the standard technique. The noise temperature gradually rose to 672 K at 820 GHz. This behaviour may be caused by RF losses from the weak-link parts, due to the steps between the distributed junctions and the microstriplines being less than 1 μm wide.

Superconductor Science and Technology•Nov 21, 2002•6 citations

Waveguide-Type SIS Receiver Using All-NbN Technique

M. TAKEDA

This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.

IEICE Transactions on Electronics•Feb 1, 2006•5 citations

High-Gap Nb-AlN-NbN SIS Junctions for Frequency Band 790–950 GHz

Andrey V. Khudchenko, Andrey M. Baryshev, Kirill I. Rudakov +4 more

We have designed, fabricated, and tested superconductor-insulator-superconductor (SIS) mixers based on Nb/AlN/NbN twin tunnel junctions for waveguide receivers operating in a frequency range of 790-950 GHz. Electromagnetic simulations and measurement results of the mixer performance are presented. The junctions have a high gap voltage of 3.15 mV and a high current density of about 30 kA/cm2, providing a wide receiver band, which was confirmed by Fourier transform spectrometer (FTS) and noise temperature measurements. The corrected receiver noise temperature varies from 240 K at low frequencies to 550 K at the high end of the band. The influence of the SIS junction heating on its characteristics has been studied and compared to another similar high current density technologies. The heating does not have a critical impact on the mixer performance.

IEEE Transactions on Terahertz Science and Technology•Dec 24, 2015•49 citations

Terahertz NbN/AlN/NbN mixers with Al/SiO/NbN microstrip tuning circuits

Yoshinori Uzawa, Zhen Wang, Akira Kawakami

We have developed a low-noise quasioptical NbN/AlN/NbN superconductor-insulator-superconductor (SIS) mixer that operates at terahertz frequencies. The mixer uses a MgO hyperhemispherical lens with an antireflection cap, a single-crystal NbN log-periodic antenna, and two-junction tuning circuits which employ Al/SiO/NbN microstriplines. The NbN/AlN/NbN junction size was about 0.9 μm in diameter, and the current density was about 45 kA/cm2. The frequency dependence of the receiver noise temperature was investigated by using an optically pumped far-infrared laser and a backward-wave oscillator as a local oscillator at several frequencies from 670 to 1082 GHz. The experimental results showed that the center frequency was around 800 GHz, and the receiver noise temperature measured by the standard Y-factor method was 457 K (DSB) at 783 GHz including a 9-μm-thick Mylar beam splitter loss and other optical losses at the physical bath temperature of 4.2 K. This is the first SIS mixer based on NbN with low-noise performance (12hν/kB) above the gap frequency of Nb.

Applied Physics Letters•Aug 3, 1998•44 citations

0.5-THz waveguide SIS mixers with NbN/AlN/NbN technology

Jing Li, Masanori Takeda, Zhen Wang +1 more

Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 29, 2007•3 citations
For the optimum design of integrated receivers operating above the gap frequency of Nb, we have designed, fabricated and tested NbN-based quasi-optical superconductor/insulator/superconductor (SIS) mixers. The mixer chip incorporates a resonant half-wavelength epitaxial NbN/AlN/NbN junction, a twin-slot antenna and their coupling circuits. We adopted two kinds of coupling circuit between the antenna and the SIS junction: one is an in-phase feed with a length of 95 µm and the other is an anti-phase feed of 30 µm length. It was found that the anti-phase mixer reveals a 3 dB bandwidth of 43% of the centre frequency; the uncorrected double-sideband receiver noise temperature TRX = 691 K at 0.91 THz and TRX = 844 K at 0.80 THz, while 17% and TRX = 1250 K at 0.79 THz for the in-phase version. Possible reasons for this difference are discussed, which could be transmission loss and its robustness with respect to the variation of junction parameters. These experimental results suggest the NbN-based distributed mixer with the anti-phase feed is a better candidate for wide-band integrated receivers operating above 0.7 THz.
We have designed, fabricated, and tested terahertz superconductor-insulator-superconductor (SIS) mixers having a self-compensated NbN/AlN/NbN tunnel junction and an epitaxially grown NbN/MgO/NbN microstripline. The junction as a distributed element was 0.8-/spl mu/m wide and 2.4-/spl mu/m long, and its current density was 50 kA/cm/sup 2/. The microstripline consisted of a 200-nm-thick NbN ground plane, a 180-nm-thick MgO insulator, and a 350-nm-thick NbN wiring layer. An investigation of the mixer in our receiver configuration showed flat noise characteristics from 870 to 960 GHz. The lowest receiver noise temperature of about 550 K was obtained at 909 GHz, including a 9-/spl mu/m-thick Mylar beam splitter loss and other optical losses. These characteristics suggest that SIS mixers with self-compensated NbN/AlN/NbN junctions and NbN/MgO/NbN microstriplines are appropriate for used in wideband and low-noise operations at terahertz frequencies.
We have designed, fabricated and tested a quasi-optical superconductor–insulator–superconductor (SIS) mixer employing distributed NbN/MgO/NbN tunnel junctions and NbN/MgO/NbN microstriplines at submillimetre-wave frequencies. These trilayers were fabricated by dc- and rf-magnetron sputtering on an MgO substrate at ambient temperature so that the NbN and MgO films were grown epitaxially. Our SIS mixer consists of an MgO hyperhemispherical lens with an antireflection cap and a self-complementary log-periodic antenna made of a single-crystal NbN film, on which the distributed SIS junctions and the two-section impedance transformers were mirror-symmetrically placed at the feed point of the antenna. As designed, the junctions are 0.6 μm wide and 15.5 μm long, which is sufficient to absorb the incoming signal along this lossy transmission line, assuming a current density of 10 kA cm −2 . The mixer showed good I – V characteristics, with subgap-to-normal resistance ratios of about 13, although weak-link breaks were observed above the gap voltage. The minimum double side band receiver noise temperature was 334 K at 678 GHz, including the input noise of about 200 K as estimated by the standard technique. The noise temperature gradually rose to 672 K at 820 GHz. This behaviour may be caused by RF losses from the weak-link parts, due to the steps between the distributed junctions and the microstriplines being less than 1 μm wide.
This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.
We have designed, fabricated, and tested superconductor-insulator-superconductor (SIS) mixers based on Nb/AlN/NbN twin tunnel junctions for waveguide receivers operating in a frequency range of 790-950 GHz. Electromagnetic simulations and measurement results of the mixer performance are presented. The junctions have a high gap voltage of 3.15 mV and a high current density of about 30 kA/cm2, providing a wide receiver band, which was confirmed by Fourier transform spectrometer (FTS) and noise temperature measurements. The corrected receiver noise temperature varies from 240 K at low frequencies to 550 K at the high end of the band. The influence of the SIS junction heating on its characteristics has been studied and compared to another similar high current density technologies. The heating does not have a critical impact on the mixer performance.
We have developed a low-noise quasioptical NbN/AlN/NbN superconductor-insulator-superconductor (SIS) mixer that operates at terahertz frequencies. The mixer uses a MgO hyperhemispherical lens with an antireflection cap, a single-crystal NbN log-periodic antenna, and two-junction tuning circuits which employ Al/SiO/NbN microstriplines. The NbN/AlN/NbN junction size was about 0.9 μm in diameter, and the current density was about 45 kA/cm2. The frequency dependence of the receiver noise temperature was investigated by using an optically pumped far-infrared laser and a backward-wave oscillator as a local oscillator at several frequencies from 670 to 1082 GHz. The experimental results showed that the center frequency was around 800 GHz, and the receiver noise temperature measured by the standard Y-factor method was 457 K (DSB) at 783 GHz including a 9-μm-thick Mylar beam splitter loss and other optical losses at the physical bath temperature of 4.2 K. This is the first SIS mixer based on NbN with low-noise performance (12hν/kB) above the gap frequency of Nb.
Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.