Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Optics Express

In-field Raman amplification on coherent optical fiber links for frequency metrology

Cecilia Clivati, Gabriele Bolognini, Davide Calonico, S. Faralli, Alberto Mura, Filippo Levi

Published Apr 16, 2015• 8 citations
Publisher

Abstract

Distributed Raman amplification (DRA) is widely exploited for the transmission of broadband, modulated signals used in data links, but not yet in coherent optical links for frequency metrology, where the requirements are rather different. After preliminary tests on fiber spools, in this paper we deeper investigate Raman amplification on deployed in-field optical metrological links. We actually test a Doppler-stabilized optical link both on a 94 km-long metro-network implementation with multiplexed ITU data channels and on a 180 km-long dedicated fiber haul connecting two cities, where DRA is employed in combination with Erbium-doped fiber amplification (EDFA). The performance of DRA is detailed in both experiments, indicating that it does not introduce noticeable penalties for the metrological signal or for the ITU data channels. We hence show that Raman amplification of metrological signals can be compatible with a wavelength division multiplexing architecture and that it can be used as an alternative or in combination with dedicated bidirectional EDFAs. No deterioration is noticed in the coherence properties of the delivered signal, which attains frequency instability at the 10(-19) level in both cases. This study can be of interest also in view of the undergoing deployment of continental fiber networks for frequency metrology.

DOI
10.1364/oe.23.010604

Related papers

Long distance ultra-stable frequency dissemination on a dedicated wavelength channel of a telecommunication network

Olivier Lopez, Paul-Éric Pottie, Bruno Chanteau +5 more

Summary form only given. The transfer of ultra-stable frequencies between distant laboratories is a fundamental issue for a wide range of high-sensitivity experiments in advanced metrology and fundamental physics. Since a few years, several experiments of optical frequency transfer were reported over dedicated fiber, with a record distance of 920 km [1] recently demonstrated in Germany. The challenge is now to build a wide frequency dissemination network connecting laboratories and research agencies in Europe.For that purpose we exploit the existing fine meshing of the Internet fiber network, connecting laboratories via the National Research Networks (NRENs). In that scheme, the ultra-stable frequency signal is copropagating simultaneously with the Internet traffic in the same fiber using a dedicated channel in a dense wavelength division multiplexing (DWDM) approach. Optical add-drop multiplexers enable to insert and extract the ultra-stable frequency signal in and from the network.We have demonstrated an ultra-stable optical link over 540 km, including 470 km of public fiber network of the French NREN (RENATER) simultaneously carrying Internet data traffic [2]. The signal bypasses four amplification stages and two Data Center Facilities using multiplexers and custom-made bidirectional erbium-doped fiber amplifiers. One specific point of this experiment is that with Internet fibers, we have a very limited control on the attenuation and noise. For instance the Erbium fiber doped bidirectional amplifiers gain is drastically limited to avoid lasing oscillations due to parasitic reflections due to connectors, splices and more fundamental Rayleigh backscattering. Nevertheless the results are comparable with those obtained with dedicated fibers. Figure 1 shows the measured fractional frequency stability, we obtain 6×10-15 at 1 s and below 10-18 after 10000 second integration time. Such optical link will enable a broad range of high-sensitivity measurements, including the search for fundamental constants variation and gravitational mapping. This concept of fiber link has been very recently used to implement a giant fiber gyroscope [3]

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•May 1, 2013•1 citation

Cascaded optical link on a telecommunication fiber network for ultra-stable frequency dissemination

Olivier Lopez, N. Chiodo, Fabio Stefani +7 more

The transfer of ultra-stable frequencies between distant laboratories is required by many applications in time and frequency metrology, fundamental physics, particle accelerators and astrophysics. Optical fiber links have been intensively studied for a decade and brought the potential to transfer frequency with a very high accuracy and stability thanks to an active compensation of the propagation noise. We are currently developing an optical metrological network using the fibers of the French National Research and Education Network. Using the so-called dark-channel approach, the ultrastable signal is copropagating with data traffic using wavelength division multiplexing. Due to significant reflections and losses along the fibers, which cannot be compensated with amplifiers, we have developed some repeater stations for the metrological signal. These remotely-operated stations amplify the ultrastable signal and compensate the propagation noise. The link is thus composed of a few cascaded spans. It gives the possibility to increase the noise correction bandwidth, which is proportional to the inverse of the fiber length for each span. These stations are a key element for the deployment of a reliable and large scale metrological network. We report here on the implementation of a two-spans cascaded link of 740 km reaching a relative stability of a few 10-20 after 103 s averaging time. Extension to longer links and alternative transfer methods will be discussed.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Mar 10, 2015•4 citations

Optical frequency transfer with below 10−21 uncertainty using a DFB–laser-based fiber Brillouin amplifier

Jaffar Emad Kadum, Jingxian Ji, Alexander Kühl +3 more

Exploiting the outstanding performance of optical atomic clocks for improved timekeeping, relativistic geodesy, and fundamental physics beyond the standard model demands comparing distant state-of-the-art optical clocks. Interferometric optical fiber links have been demonstrated as an eminent method for such frequency comparisons over distances up to thousands of kilometers. However, for such distances, the optical fiber attenuation mandates signal amplification. Fiber Brillouin amplification (FBA) has been proven as an efficient amplification technique for coherent frequency transfer. Demonstrated FBA schemes have been designed based on costly narrow-linewidth pump lasers and analog pump-to-signal phase locking schemes. Furthermore, the high pump power requirement of these FBAs hinders the integration of FBA-based frequency dissemination on fiber connections for shared telecommunication signals in the C-band. In this paper, we propose and experimentally demonstrate a novel FBA module (FBAM) employing cost-effective distributed feedback (DFB) pump lasers assisted by a digital phase locking scheme based on a field programmable gated array. The new FBAM is compact, cost-effective, and directly applicable to different bands, which opens up new opportunities to establish a frequency metrology infrastructure within existing telecommunication fiber networks. Additionally, the small-footprint of the DFB-FBAM allows for frequent amplification stages with lower pump power to reach continental scale optical metrology links with an optimized signal-to-noise ratio. We characterized the DFB-FBAM’s frequency transfer uncertainty using a two-way layout over an in-lab 100 km long optical fiber link and reach a fractional frequency instability of 9.3 × 10−22 at a 10 ks integration time. The DFB-FBAM characterizations show uncertainty contributions of (−2.1 ± 3.3) × 10−22 and below for averaging times >100 ks. For the first time, we assess the temporal Brillouin frequency shift variations in an underground fiber link and implement a scheme to track these changes in a remote FBAM.

APL Photonics•Mar 1, 2023•7 citations

Fiber Raman amplification for metrological transfer of phase-coherent optical frequencies

Gabriele Bolognini, Alberto Mura, Davide Calonico +4 more

We analyze the benefits of distributed Raman amplification in metrology transfer of phase-coherent ultra-narrowband optical frequencies in a long fiber link (200 km with additional 16 dB loss), providing high-gain bi-directional amplification with limited impact on phase noise, attaining a fractional frequency instability of 3 × 10-19 over 1000 s.

European Conference on Optical Communication•Jan 1, 2013•0 citations

Optical frequency transfer over 377 km urban fiber link using EDFAs

Xue Deng, Jie Liu, Qi Zang +6 more

We demonstrate an optical frequency transfer over a 377 km-long fiber link using three bi-directional Erbium-doped fiber amplifiers (EDFAs) to compensate the fiber attenuation. Through active phase noise cancellation, we obtain a transfer instability of 2.2×10-14 at 1 s and 6.2×10-17 at 2000 s. The lasing effects induced by EDFAs are observed in the transfer link which reduce the gain performance of the EDFAs and deteriorate the stability of the signal. In the paper, the factors that may induce the lasing effects is discussed, specially, improper phase locking parameters may stimulate the lasing effects. The phase noise of the 377 km link and the transfer instability versus fiber lengths is also researched. This work makes a good foundation for our future research on long-distance optical frequency transfer.

Tenth International Conference on Information Optics and Photonics•Nov 15, 2018•0 citations

Precise Frequency Comparison System Using Bidirectional Optical Amplifiers

M. Amemiya, Michito Imae, Y. Fujii +3 more

Precise frequency comparisons are becoming more urgent given the recent rapid progress in next-generation frequency standards. This paper describes a new type of bidirectional optical amplifier that overcomes the fiber loss limits that have prevented accurate frequency comparisons between widely separated places; such comparison is realized by bidirectionally transmitting wavelength-division-multiplexed (WDM) signals along a single fiber. The proposed optical amplifier has an optical isolator in each two-way channel divided by wavelength filters to suppress the optical reflection that causes amplification instability. The additional insertion optical loss due to this method is about 1.5 dB. The optical gain greater than 30 dB is obtained for both signals with good optical isolation of 65 dB. A radio-frequency reference signal can directly be sent by simple intensity modulation and direct detection (IM-DD) devices in the 1550-nm region widely used in telecommunication networks. Phase comparisons of the received signals and the frequency standards at each terminal are used for frequency comparisons. The amplifier is tested in the field using two hydrogen masers. A 120-km fiber with loss of 52.5 dB is used to connect the National Metrology Institute of Japan (NMIJ) to the University of Tokyo. Because of this loss, an amplifier is needed to realize sufficient receiving power. The frequency stability of the system with a 10-MHz direct transmission is evaluated by returning the optical signal from a halfway point [55 km from the NMIJ] where the amplifier is installed. The result is 2.6 × 10-16(Allan deviation) with the averaging time of 7 × 104s. The laboratory result is 8.7 × 10-17(¿ = 4 × 104s). The amplifier's long-term stability is promising for stable frequency dissemination in addition to precise frequency comparisons.

IEEE Transactions on Instrumentation and Measurement•Sep 24, 2009•41 citations
Distributed Raman amplification (DRA) is widely exploited for the transmission of broadband, modulated signals used in data links, but not yet in coherent optical links for frequency metrology, where the requirements are rather different. After preliminary tests on fiber spools, in this paper we deeper investigate Raman amplification on deployed in-field optical metrological links. We actually test a Doppler-stabilized optical link both on a 94 km-long metro-network implementation with multiplexed ITU data channels and on a 180 km-long dedicated fiber haul connecting two cities, where DRA is employed in combination with Erbium-doped fiber amplification (EDFA). The performance of DRA is detailed in both experiments, indicating that it does not introduce noticeable penalties for the metrological signal or for the ITU data channels. We hence show that Raman amplification of metrological signals can be compatible with a wavelength division multiplexing architecture and that it can be used as an alternative or in combination with dedicated bidirectional EDFAs. No deterioration is noticed in the coherence properties of the delivered signal, which attains frequency instability at the 10(-19) level in both cases. This study can be of interest also in view of the undergoing deployment of continental fiber networks for frequency metrology.
Summary form only given. The transfer of ultra-stable frequencies between distant laboratories is a fundamental issue for a wide range of high-sensitivity experiments in advanced metrology and fundamental physics. Since a few years, several experiments of optical frequency transfer were reported over dedicated fiber, with a record distance of 920 km [1] recently demonstrated in Germany. The challenge is now to build a wide frequency dissemination network connecting laboratories and research agencies in Europe.For that purpose we exploit the existing fine meshing of the Internet fiber network, connecting laboratories via the National Research Networks (NRENs). In that scheme, the ultra-stable frequency signal is copropagating simultaneously with the Internet traffic in the same fiber using a dedicated channel in a dense wavelength division multiplexing (DWDM) approach. Optical add-drop multiplexers enable to insert and extract the ultra-stable frequency signal in and from the network.We have demonstrated an ultra-stable optical link over 540 km, including 470 km of public fiber network of the French NREN (RENATER) simultaneously carrying Internet data traffic [2]. The signal bypasses four amplification stages and two Data Center Facilities using multiplexers and custom-made bidirectional erbium-doped fiber amplifiers. One specific point of this experiment is that with Internet fibers, we have a very limited control on the attenuation and noise. For instance the Erbium fiber doped bidirectional amplifiers gain is drastically limited to avoid lasing oscillations due to parasitic reflections due to connectors, splices and more fundamental Rayleigh backscattering. Nevertheless the results are comparable with those obtained with dedicated fibers. Figure 1 shows the measured fractional frequency stability, we obtain 6×10-15 at 1 s and below 10-18 after 10000 second integration time. Such optical link will enable a broad range of high-sensitivity measurements, including the search for fundamental constants variation and gravitational mapping. This concept of fiber link has been very recently used to implement a giant fiber gyroscope [3]
The transfer of ultra-stable frequencies between distant laboratories is required by many applications in time and frequency metrology, fundamental physics, particle accelerators and astrophysics. Optical fiber links have been intensively studied for a decade and brought the potential to transfer frequency with a very high accuracy and stability thanks to an active compensation of the propagation noise. We are currently developing an optical metrological network using the fibers of the French National Research and Education Network. Using the so-called dark-channel approach, the ultrastable signal is copropagating with data traffic using wavelength division multiplexing. Due to significant reflections and losses along the fibers, which cannot be compensated with amplifiers, we have developed some repeater stations for the metrological signal. These remotely-operated stations amplify the ultrastable signal and compensate the propagation noise. The link is thus composed of a few cascaded spans. It gives the possibility to increase the noise correction bandwidth, which is proportional to the inverse of the fiber length for each span. These stations are a key element for the deployment of a reliable and large scale metrological network. We report here on the implementation of a two-spans cascaded link of 740 km reaching a relative stability of a few 10-20 after 103 s averaging time. Extension to longer links and alternative transfer methods will be discussed.
Exploiting the outstanding performance of optical atomic clocks for improved timekeeping, relativistic geodesy, and fundamental physics beyond the standard model demands comparing distant state-of-the-art optical clocks. Interferometric optical fiber links have been demonstrated as an eminent method for such frequency comparisons over distances up to thousands of kilometers. However, for such distances, the optical fiber attenuation mandates signal amplification. Fiber Brillouin amplification (FBA) has been proven as an efficient amplification technique for coherent frequency transfer. Demonstrated FBA schemes have been designed based on costly narrow-linewidth pump lasers and analog pump-to-signal phase locking schemes. Furthermore, the high pump power requirement of these FBAs hinders the integration of FBA-based frequency dissemination on fiber connections for shared telecommunication signals in the C-band. In this paper, we propose and experimentally demonstrate a novel FBA module (FBAM) employing cost-effective distributed feedback (DFB) pump lasers assisted by a digital phase locking scheme based on a field programmable gated array. The new FBAM is compact, cost-effective, and directly applicable to different bands, which opens up new opportunities to establish a frequency metrology infrastructure within existing telecommunication fiber networks. Additionally, the small-footprint of the DFB-FBAM allows for frequent amplification stages with lower pump power to reach continental scale optical metrology links with an optimized signal-to-noise ratio. We characterized the DFB-FBAM’s frequency transfer uncertainty using a two-way layout over an in-lab 100 km long optical fiber link and reach a fractional frequency instability of 9.3 × 10−22 at a 10 ks integration time. The DFB-FBAM characterizations show uncertainty contributions of (−2.1 ± 3.3) × 10−22 and below for averaging times >100 ks. For the first time, we assess the temporal Brillouin frequency shift variations in an underground fiber link and implement a scheme to track these changes in a remote FBAM.
We demonstrate an optical frequency transfer over a 377 km-long fiber link using three bi-directional Erbium-doped fiber amplifiers (EDFAs) to compensate the fiber attenuation. Through active phase noise cancellation, we obtain a transfer instability of 2.2×10-14 at 1 s and 6.2×10-17 at 2000 s. The lasing effects induced by EDFAs are observed in the transfer link which reduce the gain performance of the EDFAs and deteriorate the stability of the signal. In the paper, the factors that may induce the lasing effects is discussed, specially, improper phase locking parameters may stimulate the lasing effects. The phase noise of the 377 km link and the transfer instability versus fiber lengths is also researched. This work makes a good foundation for our future research on long-distance optical frequency transfer.
Precise frequency comparisons are becoming more urgent given the recent rapid progress in next-generation frequency standards. This paper describes a new type of bidirectional optical amplifier that overcomes the fiber loss limits that have prevented accurate frequency comparisons between widely separated places; such comparison is realized by bidirectionally transmitting wavelength-division-multiplexed (WDM) signals along a single fiber. The proposed optical amplifier has an optical isolator in each two-way channel divided by wavelength filters to suppress the optical reflection that causes amplification instability. The additional insertion optical loss due to this method is about 1.5 dB. The optical gain greater than 30 dB is obtained for both signals with good optical isolation of 65 dB. A radio-frequency reference signal can directly be sent by simple intensity modulation and direct detection (IM-DD) devices in the 1550-nm region widely used in telecommunication networks. Phase comparisons of the received signals and the frequency standards at each terminal are used for frequency comparisons. The amplifier is tested in the field using two hydrogen masers. A 120-km fiber with loss of 52.5 dB is used to connect the National Metrology Institute of Japan (NMIJ) to the University of Tokyo. Because of this loss, an amplifier is needed to realize sufficient receiving power. The frequency stability of the system with a 10-MHz direct transmission is evaluated by returning the optical signal from a halfway point [55 km from the NMIJ] where the amplifier is installed. The result is 2.6 × 10-16(Allan deviation) with the averaging time of 7 × 104s. The laboratory result is 8.7 × 10-17(¿ = 4 × 104s). The amplifier's long-term stability is promising for stable frequency dissemination in addition to precise frequency comparisons.