Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Instrumentation and Measurement

Precise Frequency Comparison System Using Bidirectional Optical Amplifiers

M. Amemiya, Michito Imae, Y. Fujii, Tomonari Suzuyama, Feng-Lei Hong, Masao Takamoto

Published Sep 24, 2009• 41 citations
Publisher

Abstract

Precise frequency comparisons are becoming more urgent given the recent rapid progress in next-generation frequency standards. This paper describes a new type of bidirectional optical amplifier that overcomes the fiber loss limits that have prevented accurate frequency comparisons between widely separated places; such comparison is realized by bidirectionally transmitting wavelength-division-multiplexed (WDM) signals along a single fiber. The proposed optical amplifier has an optical isolator in each two-way channel divided by wavelength filters to suppress the optical reflection that causes amplification instability. The additional insertion optical loss due to this method is about 1.5 dB. The optical gain greater than 30 dB is obtained for both signals with good optical isolation of 65 dB. A radio-frequency reference signal can directly be sent by simple intensity modulation and direct detection (IM-DD) devices in the 1550-nm region widely used in telecommunication networks. Phase comparisons of the received signals and the frequency standards at each terminal are used for frequency comparisons. The amplifier is tested in the field using two hydrogen masers. A 120-km fiber with loss of 52.5 dB is used to connect the National Metrology Institute of Japan (NMIJ) to the University of Tokyo. Because of this loss, an amplifier is needed to realize sufficient receiving power. The frequency stability of the system with a 10-MHz direct transmission is evaluated by returning the optical signal from a halfway point [55 km from the NMIJ] where the amplifier is installed. The result is 2.6 × 10-16(Allan deviation) with the averaging time of 7 × 104s. The laboratory result is 8.7 × 10-17(¿ = 4 × 104s). The amplifier's long-term stability is promising for stable frequency dissemination in addition to precise frequency comparisons.

DOI
10.1109/tim.2009.2025073

Related papers

Long distance ultra-stable frequency dissemination on a dedicated wavelength channel of a telecommunication network

Olivier Lopez, Paul-Éric Pottie, Bruno Chanteau +5 more

Summary form only given. The transfer of ultra-stable frequencies between distant laboratories is a fundamental issue for a wide range of high-sensitivity experiments in advanced metrology and fundamental physics. Since a few years, several experiments of optical frequency transfer were reported over dedicated fiber, with a record distance of 920 km [1] recently demonstrated in Germany. The challenge is now to build a wide frequency dissemination network connecting laboratories and research agencies in Europe.For that purpose we exploit the existing fine meshing of the Internet fiber network, connecting laboratories via the National Research Networks (NRENs). In that scheme, the ultra-stable frequency signal is copropagating simultaneously with the Internet traffic in the same fiber using a dedicated channel in a dense wavelength division multiplexing (DWDM) approach. Optical add-drop multiplexers enable to insert and extract the ultra-stable frequency signal in and from the network.We have demonstrated an ultra-stable optical link over 540 km, including 470 km of public fiber network of the French NREN (RENATER) simultaneously carrying Internet data traffic [2]. The signal bypasses four amplification stages and two Data Center Facilities using multiplexers and custom-made bidirectional erbium-doped fiber amplifiers. One specific point of this experiment is that with Internet fibers, we have a very limited control on the attenuation and noise. For instance the Erbium fiber doped bidirectional amplifiers gain is drastically limited to avoid lasing oscillations due to parasitic reflections due to connectors, splices and more fundamental Rayleigh backscattering. Nevertheless the results are comparable with those obtained with dedicated fibers. Figure 1 shows the measured fractional frequency stability, we obtain 6×10-15 at 1 s and below 10-18 after 10000 second integration time. Such optical link will enable a broad range of high-sensitivity measurements, including the search for fundamental constants variation and gravitational mapping. This concept of fiber link has been very recently used to implement a giant fiber gyroscope [3]

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•May 1, 2013•1 citation

Joint stable optical frequency and precise time transfer over 406 km of shared fiber lines — Study

Josef Vojtěch, Ondřej Havliš, Martin Šlapák +17 more

We present a preliminary study of bidirectional ultra-stable optical frequency and precise time transmission over 406 km long path in the telecom-grade fiber optic infrastructure of dense wavelength division multiplexing. The main challenge in this application is the need of bidirectional amplification to compensate for signal loss. Directional non-reciprocities of the time transfer are evaluated together with their uncertainties. Solutions are proposed to significantly limit the final uncertainty.

International Conference on Telecommunications and Signal Processing (TSP)•Jul 1, 2017•6 citations

High-Precision Fiber Noise Detection and Comparison over a 260 km Field Fiber Link

Qi Zang, Xiang Zhang, Dan Wang +10 more

In this paper, we present a high-precision optical frequency noise detection and comparison technique using a two-way transfer method over a 260 km field fiber link. This method allows for the comparison of optical frequencies between remote optical references without the need for data transfer through communication. We extend a previously established two-way comparison technique to obtain all data at the local site. Two optical carrier signals are injected into the bidirectional fiber from both ends, and one carrier is reflected back from the remote end. This enables the phase comparison of the two carrier signals at a single site without the need to transmit experimental data. The common-mode frequency noise induced by the bidirectional fiber link is detected and effectively suppressed without the need for sophisticated active fiber noise control. Our demonstration system, which uses a 260 km field fiber link and a common laser source, achieves a fractional instability of 2.5×10-17 at 1 s averaging time and scales down to 3.5×10-21 at 8000 s. This scheme offers the distinct advantage of completing the comparison at a single site, eliminating the need for remote data transfer via communication. This method is expected to enhance reliability for high-precision frequency comparisons between remote optical clocks and advanced atomic clocks.

Sensors•May 28, 2024•1 citation

Exploring High-Precision Transmission of Optical Reference Frequencies via Wavelength Division Multiplexing

Kota Nishiyama, Mayuri Nakagawa, Kohjun Koshiji +6 more

Transmitting an ultra-high precision frequency of an optical clock via wavelength division multiplexing (WDM) is a key technology for economically realizing innovative applications enabled by significantly accurate and stable time and frequency. In this study, we investigated an optical frequency transmission method using a commercial WDM system, employing our highly stable optical frequency repeater systems with a fiber noise compensation (FNC) function. For the 20-km WDM transmission, we achieved the frequency instability of 4 × 10–15at an averaging time of 1 second (s) and reaches ~ 1 × 10–18at 34,000 s. This frequency stability enables optical clock reference frequencies to be transmitted over long distances, demonstrating the potential of our WDM link to enable the widespread deployment of the optical clock frequency at the frontier of precision.

IEEE International Conference on High Performance Switching and Routing (HPSR)•May 20, 2025•0 citations

Multiplexed optical link for ultra-stable frequency dissemination

Olivier Lopez, Bruno Chanteau, Vincent Roncin +6 more

We transfer the frequency of an ultra-stable laser over a cascaded optical link comprising two compensated links of 150 km and a repeater station. Each link passes through two important nodes of the telecommunication network and includes 114 km of Internet fiber simultaneously carrying data traffic, through a dense wavelength division multiplexing scheme. The metrological signal is inserted in and extracted from the communication network using bidirectional optical add-drop multiplexers. The repeater station is working independently without any remote control. The phase noise on the two links is compensated with the usual round-trip technique. The 300-km multiplexed cascaded link shows an Allan deviation of 3×10-15at one second and 7×10-20at 20 hours. This work paves the way to a wide dissemination of ultra stable optical clock signals between distant laboratories via the Internet network.

Joint Conference of the European Frequency and Time Forum and IEEE International Frequency Control Symposium (EFTF/IFCS)•Jun 1, 2010•3 citations

Polarization-Insensitive Coherent Receiving in Optical Fiber Links for Frequency Metrology

Stefano Paracchino, Cecilia Clivati, Paolo Savio +3 more

In recent years, the dissemination of optical frequency signals along phase-stabilized fibers has allowed the comparison of optical clocks at unprecedented levels of accuracy. This has a strong relevance in frequency metrology and boosted the measurement capabilities also in other research fields such as radioastronomy [1], geodesy [2] and fundamental physics [3]. Fiber-based frequency dissemination relies on the transmission of a continuous-wave, narrow-linewidth laser whose frequency is accurately measured with an atomic clock at the National Metrology Institute (NMI) where it is generated. Specific techniques are used to compensate for the acoustic and seismic noise and temperature variations, which degrade the phase stability of the transmitted signal. However, in existing implementations, it is not possible to detect and compensate for the birefringence variations of the optical fiber. These can induce variations in the state of polarization (SOP) of the transmitted signal, affecting the optical beatnotes at the receiving end. This not only degrades the achievable performances in terms of phase stability of the metrological signal, but can also lead to beatnote fading, with consequent failure of the entire system. This problem currently represents one of the strongest limitations to the reliability of fiber-based frequency dissemination.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 1, 2019•0 citations
Precise frequency comparisons are becoming more urgent given the recent rapid progress in next-generation frequency standards. This paper describes a new type of bidirectional optical amplifier that overcomes the fiber loss limits that have prevented accurate frequency comparisons between widely separated places; such comparison is realized by bidirectionally transmitting wavelength-division-multiplexed (WDM) signals along a single fiber. The proposed optical amplifier has an optical isolator in each two-way channel divided by wavelength filters to suppress the optical reflection that causes amplification instability. The additional insertion optical loss due to this method is about 1.5 dB. The optical gain greater than 30 dB is obtained for both signals with good optical isolation of 65 dB. A radio-frequency reference signal can directly be sent by simple intensity modulation and direct detection (IM-DD) devices in the 1550-nm region widely used in telecommunication networks. Phase comparisons of the received signals and the frequency standards at each terminal are used for frequency comparisons. The amplifier is tested in the field using two hydrogen masers. A 120-km fiber with loss of 52.5 dB is used to connect the National Metrology Institute of Japan (NMIJ) to the University of Tokyo. Because of this loss, an amplifier is needed to realize sufficient receiving power. The frequency stability of the system with a 10-MHz direct transmission is evaluated by returning the optical signal from a halfway point [55 km from the NMIJ] where the amplifier is installed. The result is 2.6 × 10-16(Allan deviation) with the averaging time of 7 × 104s. The laboratory result is 8.7 × 10-17(¿ = 4 × 104s). The amplifier's long-term stability is promising for stable frequency dissemination in addition to precise frequency comparisons.
Summary form only given. The transfer of ultra-stable frequencies between distant laboratories is a fundamental issue for a wide range of high-sensitivity experiments in advanced metrology and fundamental physics. Since a few years, several experiments of optical frequency transfer were reported over dedicated fiber, with a record distance of 920 km [1] recently demonstrated in Germany. The challenge is now to build a wide frequency dissemination network connecting laboratories and research agencies in Europe.For that purpose we exploit the existing fine meshing of the Internet fiber network, connecting laboratories via the National Research Networks (NRENs). In that scheme, the ultra-stable frequency signal is copropagating simultaneously with the Internet traffic in the same fiber using a dedicated channel in a dense wavelength division multiplexing (DWDM) approach. Optical add-drop multiplexers enable to insert and extract the ultra-stable frequency signal in and from the network.We have demonstrated an ultra-stable optical link over 540 km, including 470 km of public fiber network of the French NREN (RENATER) simultaneously carrying Internet data traffic [2]. The signal bypasses four amplification stages and two Data Center Facilities using multiplexers and custom-made bidirectional erbium-doped fiber amplifiers. One specific point of this experiment is that with Internet fibers, we have a very limited control on the attenuation and noise. For instance the Erbium fiber doped bidirectional amplifiers gain is drastically limited to avoid lasing oscillations due to parasitic reflections due to connectors, splices and more fundamental Rayleigh backscattering. Nevertheless the results are comparable with those obtained with dedicated fibers. Figure 1 shows the measured fractional frequency stability, we obtain 6×10-15 at 1 s and below 10-18 after 10000 second integration time. Such optical link will enable a broad range of high-sensitivity measurements, including the search for fundamental constants variation and gravitational mapping. This concept of fiber link has been very recently used to implement a giant fiber gyroscope [3]
We present a preliminary study of bidirectional ultra-stable optical frequency and precise time transmission over 406 km long path in the telecom-grade fiber optic infrastructure of dense wavelength division multiplexing. The main challenge in this application is the need of bidirectional amplification to compensate for signal loss. Directional non-reciprocities of the time transfer are evaluated together with their uncertainties. Solutions are proposed to significantly limit the final uncertainty.
In this paper, we present a high-precision optical frequency noise detection and comparison technique using a two-way transfer method over a 260 km field fiber link. This method allows for the comparison of optical frequencies between remote optical references without the need for data transfer through communication. We extend a previously established two-way comparison technique to obtain all data at the local site. Two optical carrier signals are injected into the bidirectional fiber from both ends, and one carrier is reflected back from the remote end. This enables the phase comparison of the two carrier signals at a single site without the need to transmit experimental data. The common-mode frequency noise induced by the bidirectional fiber link is detected and effectively suppressed without the need for sophisticated active fiber noise control. Our demonstration system, which uses a 260 km field fiber link and a common laser source, achieves a fractional instability of 2.5×10-17 at 1 s averaging time and scales down to 3.5×10-21 at 8000 s. This scheme offers the distinct advantage of completing the comparison at a single site, eliminating the need for remote data transfer via communication. This method is expected to enhance reliability for high-precision frequency comparisons between remote optical clocks and advanced atomic clocks.
Transmitting an ultra-high precision frequency of an optical clock via wavelength division multiplexing (WDM) is a key technology for economically realizing innovative applications enabled by significantly accurate and stable time and frequency. In this study, we investigated an optical frequency transmission method using a commercial WDM system, employing our highly stable optical frequency repeater systems with a fiber noise compensation (FNC) function. For the 20-km WDM transmission, we achieved the frequency instability of 4 × 10–15at an averaging time of 1 second (s) and reaches ~ 1 × 10–18at 34,000 s. This frequency stability enables optical clock reference frequencies to be transmitted over long distances, demonstrating the potential of our WDM link to enable the widespread deployment of the optical clock frequency at the frontier of precision.
We transfer the frequency of an ultra-stable laser over a cascaded optical link comprising two compensated links of 150 km and a repeater station. Each link passes through two important nodes of the telecommunication network and includes 114 km of Internet fiber simultaneously carrying data traffic, through a dense wavelength division multiplexing scheme. The metrological signal is inserted in and extracted from the communication network using bidirectional optical add-drop multiplexers. The repeater station is working independently without any remote control. The phase noise on the two links is compensated with the usual round-trip technique. The 300-km multiplexed cascaded link shows an Allan deviation of 3×10-15at one second and 7×10-20at 20 hours. This work paves the way to a wide dissemination of ultra stable optical clock signals between distant laboratories via the Internet network.
In recent years, the dissemination of optical frequency signals along phase-stabilized fibers has allowed the comparison of optical clocks at unprecedented levels of accuracy. This has a strong relevance in frequency metrology and boosted the measurement capabilities also in other research fields such as radioastronomy [1], geodesy [2] and fundamental physics [3]. Fiber-based frequency dissemination relies on the transmission of a continuous-wave, narrow-linewidth laser whose frequency is accurately measured with an atomic clock at the National Metrology Institute (NMI) where it is generated. Specific techniques are used to compensate for the acoustic and seismic noise and temperature variations, which degrade the phase stability of the transmitted signal. However, in existing implementations, it is not possible to detect and compensate for the birefringence variations of the optical fiber. These can induce variations in the state of polarization (SOP) of the transmitted signal, affecting the optical beatnotes at the receiving end. This not only degrades the achievable performances in terms of phase stability of the metrological signal, but can also lead to beatnote fading, with consequent failure of the entire system. This problem currently represents one of the strongest limitations to the reliability of fiber-based frequency dissemination.