Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Measurement Science and Technology

A simple nozzle design for high speed-ratio molecular beams

J. R. Buckland, Robert L. Folkerts, R. B. Balsod, William Allison

Published Aug 1, 1997• 20 citations
Publisher

Abstract

A simple nozzle design for a free-jet atomic beam source is described. The design is compact (< 20 mm) and uses commercially available parts with only minor modification. Characterization of the source with a helium beam and time-of-flight detector showed that a velocity spread of less than 1% is readily obtained.
DOI
10.1088/0957-0233/8/8/016

Related papers

A free jet (supersonic), molecular beam source with automatized, 50 nm precision nozzle-skimmer positioning

Sabrina D. Eder, B. Samelin, G. Bracco +2 more

Low energy (thermal) free jet (supersonic) molecular beams are used in a range of applications from surface science and surface deposition to quantum coherence and gas kinetics experiments. A free jet molecular beam is created by a gas expansion from a high pressure reservoir through a small aperture (nozzle). The nozzle typically has a diameter of 2-20 μm. The central part of the beam is selected using a skimmer, typically up to 500 μm in diameter. Recent years have seen the introduction of highly spatially confined beam sources based on micrometer skimmers and micrometer or even sub-micrometer nozzles. Such sources have been applied, for example, in the investigation of superfluidity and in neutral helium microscopy. However, up till now no source design allowing the precise positioning of the micro-skimmer relative to the nozzle has been available. This is an important issue because the relative position of skimmer and nozzle can influence the beam properties considerably. Here we present the design and implementation of a new molecular beam source, which allows an automatized, 50 nm precision positioning of the skimmer relative to the nozzle. The source is liquid nitrogen cooled and the temperature can be controlled between 110 K and 350 K with a temperature fluctuation of less than ±0.1 K over several hours. Beam intensity measurements using a 5 μm nozzle and a skimmer 5 μm in diameter are presented for stagnation pressures po in the range 3-180 bars. A 2D beam profile scan, using a 9.5 μm skimmer and a 5 μm nozzle is presented as a further documentation of the versatility of the new design and as an illustration of the influence of the relative skimmer-nozzle position on the beam properties.

Review of Scientific Instruments•Sep 1, 2013•19 citations

A compact and highly collimated atomic/molecular beam source

Geetika Bhardwaj, Saurabh Kumar Singh, Pranav R. Shirhatti

We describe the design, characterization, and application of a simple, highly collimated, and compact atomic/molecular beam source. This source is based on a segmented capillary design, constructed using a syringe needle. Angular width measurements and free molecular flow simulations show that the segmented structure effectively suppresses atoms traveling in off-axis directions, resulting in a narrow beam of Helium atoms having a width of 7 mrad (full width half maximum). We demonstrate an application of this source by using it for monitoring real-time changes in surface coverage on a clean Cu(110) surface exposed to oxygen by measuring the specular reflectivity of the Helium beam generated using this source.

arXiv:2301.13407•Review of Scientific Instruments•Apr 1, 2023•1 citation

Simple and compact nozzle design for laser vaporization sources

Mark Kokish, Matthew Dietrich, Brian Odom

Abstract We have developed and implemented a compact transparent nozzle for use in laser vaporization sources. This nozzle eliminates the need for an ablation aperture, allowing for a more intense molecular beam. We use this nozzle to prepare a molecular beam of aluminum monohydride (AlH) suitable for ion trap loading of AlH + via photoionization in ultra-high vacuum. We demonstrate stable AlH production over hour time scales using a liquid ablation target. The long-term stability, low heat load and fast ion production rate of this source are well-suited to molecular ion experiments employing destructive state readout schemes requiring frequent trap reloading.

arXiv:1509.04208•Journal of Physics B Atomic Molecular and Optical Physics•Jan 8, 2016•0 citations

A High Intensity Cold Atom Source

Jeremy Glick, William Huntington, Daniel J. Heinzen

A method for producing a high intensity cold atomic beam is discussed. The method is based on post-nozzle seeding of lithium into a supersonic helium jet.

•Jan 1, 2024•0 citations

Pulsed metastable atomic beam source for time-of-flight applications

Armin KOHLHASE, Shigetomo KITA

A metastable atomic beam source was developed utilizing pulsed helium and argon nozzle beams. A coaxial electron gun, which can be used in a pulsed as well as in a continuous mode, excites the noble gases to their metastable states by electron bombardment in the direction of propagation of the ground-state atoms. In contrast to former work, the electron beam is controlled and accelerated by a combination of three hemispherically shaped tungsten grids. With continuous electron gun operation the source produces a metastable flux of about 1015 atoms/sr s for helium and argon under optimum expansion conditions. Applying short electrical pulses to a control grid yields supersonic metastable atom pulses, with velocity distributions having a relative width as low as 3.8% for helium and 6.5% for argon ( FWHM ) with a 100% modulation of the metastable beams. These features make the source applicable for velocity analyzed scattering experiments using the time-of-flight technique.

Review of Scientific Instruments•Dec 1, 1986•16 citations

Minimizing interference in low-pressure supersonic beam sources

Jack Kelsall, Aleksandar Radić, John Ellis +2 more

Free-jet atomic, cluster, and molecular sources are typically used to produce beams of low-energy, neutral particles and find application in a wide array of technologies, from neutral atom microscopes to instruments for surface processing. We present a simple analytical theory that is applicable to many of these sources, when (i) the nozzle-skimmer distance is such that free molecular flow is achieved and (ii) there is negligible interference within the skimmer itself. The utility of the model is demonstrated by comparing experimental data with calculations performed using the theory. In particular, we show that skimmer interference is negligible compared to attenuation by "background" gas for room-temperature beams. Our treatment does not depend on any free parameters and obviates the complexity of previous theories. As a result, we are able to devise a number of design recommendations to minimize interference in sources operating with cryogenic-temperature beams.

The Journal of Chemical Physics•Mar 4, 2025•3 citations
Low energy (thermal) free jet (supersonic) molecular beams are used in a range of applications from surface science and surface deposition to quantum coherence and gas kinetics experiments. A free jet molecular beam is created by a gas expansion from a high pressure reservoir through a small aperture (nozzle). The nozzle typically has a diameter of 2-20 μm. The central part of the beam is selected using a skimmer, typically up to 500 μm in diameter. Recent years have seen the introduction of highly spatially confined beam sources based on micrometer skimmers and micrometer or even sub-micrometer nozzles. Such sources have been applied, for example, in the investigation of superfluidity and in neutral helium microscopy. However, up till now no source design allowing the precise positioning of the micro-skimmer relative to the nozzle has been available. This is an important issue because the relative position of skimmer and nozzle can influence the beam properties considerably. Here we present the design and implementation of a new molecular beam source, which allows an automatized, 50 nm precision positioning of the skimmer relative to the nozzle. The source is liquid nitrogen cooled and the temperature can be controlled between 110 K and 350 K with a temperature fluctuation of less than ±0.1 K over several hours. Beam intensity measurements using a 5 μm nozzle and a skimmer 5 μm in diameter are presented for stagnation pressures po in the range 3-180 bars. A 2D beam profile scan, using a 9.5 μm skimmer and a 5 μm nozzle is presented as a further documentation of the versatility of the new design and as an illustration of the influence of the relative skimmer-nozzle position on the beam properties.
We describe the design, characterization, and application of a simple, highly collimated, and compact atomic/molecular beam source. This source is based on a segmented capillary design, constructed using a syringe needle. Angular width measurements and free molecular flow simulations show that the segmented structure effectively suppresses atoms traveling in off-axis directions, resulting in a narrow beam of Helium atoms having a width of 7 mrad (full width half maximum). We demonstrate an application of this source by using it for monitoring real-time changes in surface coverage on a clean Cu(110) surface exposed to oxygen by measuring the specular reflectivity of the Helium beam generated using this source.
Abstract We have developed and implemented a compact transparent nozzle for use in laser vaporization sources. This nozzle eliminates the need for an ablation aperture, allowing for a more intense molecular beam. We use this nozzle to prepare a molecular beam of aluminum monohydride (AlH) suitable for ion trap loading of AlH + via photoionization in ultra-high vacuum. We demonstrate stable AlH production over hour time scales using a liquid ablation target. The long-term stability, low heat load and fast ion production rate of this source are well-suited to molecular ion experiments employing destructive state readout schemes requiring frequent trap reloading.
A metastable atomic beam source was developed utilizing pulsed helium and argon nozzle beams. A coaxial electron gun, which can be used in a pulsed as well as in a continuous mode, excites the noble gases to their metastable states by electron bombardment in the direction of propagation of the ground-state atoms. In contrast to former work, the electron beam is controlled and accelerated by a combination of three hemispherically shaped tungsten grids. With continuous electron gun operation the source produces a metastable flux of about 1015 atoms/sr s for helium and argon under optimum expansion conditions. Applying short electrical pulses to a control grid yields supersonic metastable atom pulses, with velocity distributions having a relative width as low as 3.8% for helium and 6.5% for argon ( FWHM ) with a 100% modulation of the metastable beams. These features make the source applicable for velocity analyzed scattering experiments using the time-of-flight technique.
Free-jet atomic, cluster, and molecular sources are typically used to produce beams of low-energy, neutral particles and find application in a wide array of technologies, from neutral atom microscopes to instruments for surface processing. We present a simple analytical theory that is applicable to many of these sources, when (i) the nozzle-skimmer distance is such that free molecular flow is achieved and (ii) there is negligible interference within the skimmer itself. The utility of the model is demonstrated by comparing experimental data with calculations performed using the theory. In particular, we show that skimmer interference is negligible compared to attenuation by "background" gas for room-temperature beams. Our treatment does not depend on any free parameters and obviates the complexity of previous theories. As a result, we are able to devise a number of design recommendations to minimize interference in sources operating with cryogenic-temperature beams.