Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Optics Express

First demonstration of high-order QAM signal amplification in PPLN-based phase sensitive amplifier

Takeshi Umeki, Osamu Tadanaga, Masaki Asobe, Y. Miyamoto, Hirokazu Takenouchi

Published Jan 29, 2014• 60 citations
Publisher

Abstract

We demonstrate the phase sensitive amplification of a high-order quadrature amplitude modulation (QAM) signal using non-degenerate parametric amplification in a periodically poled lithium niobate (PPLN) waveguide. The interaction between the pump, signal, and phase-conjugated idler enables us to amplify arbitrary phase components of the signal. The 16QAM signals are amplified without distortion because of the high gain linearity of the PPLN-based phase sensitive amplifier (PSA). Both the phase and amplitude noise reduction capabilities of the PSA are ensured. Phase noise cancellation is achieved by using the interaction with the phase-conjugated idler. A degraded signal-to-noise ratio (SNR) is restored by using the gain difference between a phase-correlated signal-idler pair and uncorrelated excess noise. The applicability of the simultaneous amplification of multi-carrier signals and the amplification of two independent polarization signals are also confirmed with a view to realizing ultra-high spectrally efficient signal amplification.

DOI
10.1364/oe.22.002473

Related papers

In-line phase-sensitive amplification of QPSK signal using multiple quasi-phase matched LiNbO_3 waveguide

Masaki Asobe, Takeshi Umeki, Hirokazu Takenouchi +1 more

Phase-sensitive amplifiers (PSA) using periodically poled (PPLN) LiNbO₃ waveguides are promising as low-noise optical amplifiers. However, it is difficult to realize in-line operation for multi-level phase modulated signals using a PPLN based PSA with the conventional configuration. In this paper, we report a PPLN based in-line PSA that can regenerate quadrature phase shift keying (QPSK) signals. Multi-stage frequency mixing in a multiple quasi-phase matched LiNbO₃waveguide allows carrier phase recovery from a QPSK signal. Non-degenerate parametric amplification enables the phase-sensitive amplification of a QPSK signal. Amplitude and phase regeneration is examined utilizing gain saturation and phase squeezing capability.

Optics Express•Oct 21, 2014•15 citations

Phase-squeezing properties of non-degenerate PSAs using PPLN waveguides

Benjamin James Puttnam, Dániel Mazroa, Satoshi Shinada +1 more

We investigate the phase squeezing characteristics of non-degenerate phase-sensitive-amplifiers (PSAs) based on periodically-poled-lithium-niobate (PPLN) waveguides. We implement two PSA configurations with phase insensitive idler generation performed in both highly-non-linear-fiber (HNLF) and PPLN waveguides. In both cases we demonstrate regeneration of a noisy BPSK signal, despite net signal attenuation in the phase sensitive PPLN, and show that the level of phase squeezing varies with the phase sensitive dynamic range (PSDR). We observe that weak idler generation in the PPLN limits the achievable PSDR and that use of HNLF for idler generation leads to the largest PSDR. However, in phase regeneration measurements we observe that the pump phase modulation, required to overcome stimulated Brillouin scattering, adds significant amplitude noise, which increases with the PSDR.

IEICE Technical Report; IEICE Tech. Rep.•Oct 20, 2011•0 citations

Phase-squeezing properties of non-degenerate PSAs using PPLN waveguides

Benjamin James Puttnam, Dániel Mazroa, Satoshi Shinada +1 more

We investigate the phase squeezing characteristics of non-degenerate phase-sensitive-amplifiers (PSAs) based on periodically-poled-lithium-niobate (PPLN) waveguides. We implement two PSA configurations with phase insensitive idler generation performed in both highly-non-linear-fiber (HNLF) and PPLN waveguides. In both cases we demonstrate regeneration of a noisy BPSK signal, despite net signal attenuation in the phase sensitive PPLN, and show that the level of phase squeezing varies with the phase sensitive dynamic range (PSDR). We observe that weak idler generation in the PPLN limits the achievable PSDR and that use of HNLF for idler generation leads to the largest PSDR. However, in phase regeneration measurements we observe that the pump phase modulation, required to overcome stimulated Brillouin scattering, adds significant amplitude noise, which increases with the PSDR.

Optics Express•Nov 17, 2011•47 citations

Phase sensitive amplification with noise figure below the 3 dB quantum limit using CW pumped PPLN waveguide

Masaki Asobe, Takeshi Umeki, Osamu Tadanaga

The noise figure (NF) of a phase sensitive amplifier (PSA) based on a periodically poled LiNbO3 (PPLN) waveguide was evaluated in the optical and electrical domains. Phase sensitive amplification was realized using degenerate parametric amplification in the PPLN waveguide, which was pumped by the second harmonic frequency of the signal. Second harmonic pumping enables direct observation of the intrinsic amplified spontaneous emission (ASE), which determined the NF of the PSA. An NF below the 3 dB quantum limit was obtained by observing the intrinsic ASE. The low NF was also confirmed via the noise floor measurement of a cascaded PSA and erbium doped fiber amplifier in the electrical domain. The PSA was used as a preamplifier for detecting a 40 Gbit/s phase shift keying signal. The low noise characteristics were confirmed by the improved sensitivity.

Optics Express•May 25, 2012•60 citations

Phase sensitive amplification based on cascaded SHG/DFG process in a periodically poled lithium niobate waveguide

Francesca R. Parmigiani, Kwang Jo Lee, Sheng Liu +4 more

Phase-sensitive amplifiers (PSAs) have long been known to offer the possibility of amplification with a noise figure below the 3 dB quantum limit of phase insensitive amplifiers (PIA). Other advantages of the PSAs are the potential for optical signal processing, including all optical phase regeneration of phase encoded signals, dispersion compensation and coherent wavelength exchange. PSAs are usually demonstrated using highly nonlinear fibres as the nonlinear element. However, the use of cascaded sum- and difference-frequency generation (cSFG/DFG) of second-order nonlinearities in periodically poled lithium niobate (PPLN) waveguides offers a number of attractive features relative to corresponding fibre based PSA implementations including the prospect of compact devices, large operational bandwidths and importantly a far greater immunity to the effects of Stimulated Brillouin Scattering (SBS) of the pump beams which imposes performance limitations and adds complexity to silica fibre based PSA devices. Herein, we propose and demonstrate both theoretically and experimentally a new scheme for frequency non-degenerate PSA based on the cSHG/DFG process in a single PPLN waveguide.

•Jan 1, 2009•0 citations

Phase Sensitive Amplification in a Periodically Poled Silica Fiber

Nicolas Englebert, Francesco De Lucia, Pier J. A. Sazio +2 more

Summary form only given. When a signal propagates through a transmission line, it is deteriorated by amplitude and phase noise, which reduces its signal-to-noise ratio (SNR) [1]. According to Shannon's theory, the SNR determines the maximum spectral efficiency. It is therefore necessary to limit the noise [3]. For this purpose, one can use phase sensitive amplifiers (PSA) instead of phase insensitive amplifiers (PIA) like Erbium-doped fiber amplifiers. PSAs amplify only one phase quadrature of the signal while deamplifying the other, thanks to a required phase relationship between the pump and the signal. This unique property, known as phase-squeezing, allows to obtain noise figures (NF) as low as 0 dB whereas PIAs, based on stimulated emission, cannot be go below the 3 dB quantum limit [2]. Moreover, the phase-squeezing property of PSAs can be used for quantum communication or even in metrology [1]. PSA can be realized with χ(2)material through degenerate parametric amplification [2]. The large spectral separation between the pump and the signal makes it very easy to filter out the pump after amplification. A ± 11 dB amplification with a sub-quantum NF and a regeneration of a DPSK signal was experimentally performed in LiNbO3 [3]. A fiber based approach would however be preferable for telecommunication purposes. PSA's based on four wave-mixing have been demonstrated, but the long length and the difficulty to separate pump from the signal [1] hinders its practical implementation. Here we present the first demonstration of a PSA based on periodically poled silica fiber (PPSF). This design has the advantage of all-fiber devices as well as simple pump filtering. The experimental set-up is depicted in Figure 1. A 20 mW CW fiber laser at 1550 nm is sent through a 99:1 coupler to be divided into a signal and a pump. The pump is modulated into 1 ns wide pulses with a repetition rate of 50 MHz. It is then amplified and frequency doubled in a PPLN crystal. The peak power of the 775 nm pump pulses reaches 10W. The pump and CW signal are then combined in a WDM and sent through a 30 cm long PPSF [4] where the signal undergoes parametric amplification. A second WDM is used to separate the pump from the amplified signal. The wave plates and the polarization controller in the pump path, allow to simultaneously control the polarization of the pump and the power in the fundamental mode of the PPSF (at 775 nm the fibre is slightly multimode). The relative phase between the pump and signal is controlled by fine tuning the frequency of the laser via a built-in piezo.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 1, 2019•0 citations
We demonstrate the phase sensitive amplification of a high-order quadrature amplitude modulation (QAM) signal using non-degenerate parametric amplification in a periodically poled lithium niobate (PPLN) waveguide. The interaction between the pump, signal, and phase-conjugated idler enables us to amplify arbitrary phase components of the signal. The 16QAM signals are amplified without distortion because of the high gain linearity of the PPLN-based phase sensitive amplifier (PSA). Both the phase and amplitude noise reduction capabilities of the PSA are ensured. Phase noise cancellation is achieved by using the interaction with the phase-conjugated idler. A degraded signal-to-noise ratio (SNR) is restored by using the gain difference between a phase-correlated signal-idler pair and uncorrelated excess noise. The applicability of the simultaneous amplification of multi-carrier signals and the amplification of two independent polarization signals are also confirmed with a view to realizing ultra-high spectrally efficient signal amplification.
Phase-sensitive amplifiers (PSA) using periodically poled (PPLN) LiNbO₃ waveguides are promising as low-noise optical amplifiers. However, it is difficult to realize in-line operation for multi-level phase modulated signals using a PPLN based PSA with the conventional configuration. In this paper, we report a PPLN based in-line PSA that can regenerate quadrature phase shift keying (QPSK) signals. Multi-stage frequency mixing in a multiple quasi-phase matched LiNbO₃waveguide allows carrier phase recovery from a QPSK signal. Non-degenerate parametric amplification enables the phase-sensitive amplification of a QPSK signal. Amplitude and phase regeneration is examined utilizing gain saturation and phase squeezing capability.
We investigate the phase squeezing characteristics of non-degenerate phase-sensitive-amplifiers (PSAs) based on periodically-poled-lithium-niobate (PPLN) waveguides. We implement two PSA configurations with phase insensitive idler generation performed in both highly-non-linear-fiber (HNLF) and PPLN waveguides. In both cases we demonstrate regeneration of a noisy BPSK signal, despite net signal attenuation in the phase sensitive PPLN, and show that the level of phase squeezing varies with the phase sensitive dynamic range (PSDR). We observe that weak idler generation in the PPLN limits the achievable PSDR and that use of HNLF for idler generation leads to the largest PSDR. However, in phase regeneration measurements we observe that the pump phase modulation, required to overcome stimulated Brillouin scattering, adds significant amplitude noise, which increases with the PSDR.
We investigate the phase squeezing characteristics of non-degenerate phase-sensitive-amplifiers (PSAs) based on periodically-poled-lithium-niobate (PPLN) waveguides. We implement two PSA configurations with phase insensitive idler generation performed in both highly-non-linear-fiber (HNLF) and PPLN waveguides. In both cases we demonstrate regeneration of a noisy BPSK signal, despite net signal attenuation in the phase sensitive PPLN, and show that the level of phase squeezing varies with the phase sensitive dynamic range (PSDR). We observe that weak idler generation in the PPLN limits the achievable PSDR and that use of HNLF for idler generation leads to the largest PSDR. However, in phase regeneration measurements we observe that the pump phase modulation, required to overcome stimulated Brillouin scattering, adds significant amplitude noise, which increases with the PSDR.
The noise figure (NF) of a phase sensitive amplifier (PSA) based on a periodically poled LiNbO3 (PPLN) waveguide was evaluated in the optical and electrical domains. Phase sensitive amplification was realized using degenerate parametric amplification in the PPLN waveguide, which was pumped by the second harmonic frequency of the signal. Second harmonic pumping enables direct observation of the intrinsic amplified spontaneous emission (ASE), which determined the NF of the PSA. An NF below the 3 dB quantum limit was obtained by observing the intrinsic ASE. The low NF was also confirmed via the noise floor measurement of a cascaded PSA and erbium doped fiber amplifier in the electrical domain. The PSA was used as a preamplifier for detecting a 40 Gbit/s phase shift keying signal. The low noise characteristics were confirmed by the improved sensitivity.
Phase-sensitive amplifiers (PSAs) have long been known to offer the possibility of amplification with a noise figure below the 3 dB quantum limit of phase insensitive amplifiers (PIA). Other advantages of the PSAs are the potential for optical signal processing, including all optical phase regeneration of phase encoded signals, dispersion compensation and coherent wavelength exchange. PSAs are usually demonstrated using highly nonlinear fibres as the nonlinear element. However, the use of cascaded sum- and difference-frequency generation (cSFG/DFG) of second-order nonlinearities in periodically poled lithium niobate (PPLN) waveguides offers a number of attractive features relative to corresponding fibre based PSA implementations including the prospect of compact devices, large operational bandwidths and importantly a far greater immunity to the effects of Stimulated Brillouin Scattering (SBS) of the pump beams which imposes performance limitations and adds complexity to silica fibre based PSA devices. Herein, we propose and demonstrate both theoretically and experimentally a new scheme for frequency non-degenerate PSA based on the cSHG/DFG process in a single PPLN waveguide.
Summary form only given. When a signal propagates through a transmission line, it is deteriorated by amplitude and phase noise, which reduces its signal-to-noise ratio (SNR) [1]. According to Shannon's theory, the SNR determines the maximum spectral efficiency. It is therefore necessary to limit the noise [3]. For this purpose, one can use phase sensitive amplifiers (PSA) instead of phase insensitive amplifiers (PIA) like Erbium-doped fiber amplifiers. PSAs amplify only one phase quadrature of the signal while deamplifying the other, thanks to a required phase relationship between the pump and the signal. This unique property, known as phase-squeezing, allows to obtain noise figures (NF) as low as 0 dB whereas PIAs, based on stimulated emission, cannot be go below the 3 dB quantum limit [2]. Moreover, the phase-squeezing property of PSAs can be used for quantum communication or even in metrology [1]. PSA can be realized with χ(2)material through degenerate parametric amplification [2]. The large spectral separation between the pump and the signal makes it very easy to filter out the pump after amplification. A ± 11 dB amplification with a sub-quantum NF and a regeneration of a DPSK signal was experimentally performed in LiNbO3 [3]. A fiber based approach would however be preferable for telecommunication purposes. PSA's based on four wave-mixing have been demonstrated, but the long length and the difficulty to separate pump from the signal [1] hinders its practical implementation. Here we present the first demonstration of a PSA based on periodically poled silica fiber (PPSF). This design has the advantage of all-fiber devices as well as simple pump filtering. The experimental set-up is depicted in Figure 1. A 20 mW CW fiber laser at 1550 nm is sent through a 99:1 coupler to be divided into a signal and a pump. The pump is modulated into 1 ns wide pulses with a repetition rate of 50 MHz. It is then amplified and frequency doubled in a PPLN crystal. The peak power of the 775 nm pump pulses reaches 10W. The pump and CW signal are then combined in a WDM and sent through a 30 cm long PPSF [4] where the signal undergoes parametric amplification. A second WDM is used to separate the pump from the amplified signal. The wave plates and the polarization controller in the pump path, allow to simultaneously control the polarization of the pump and the power in the fundamental mode of the PPSF (at 775 nm the fibre is slightly multimode). The relative phase between the pump and signal is controlled by fine tuning the frequency of the laser via a built-in piezo.