Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Applied Physics

The current–voltage characteristics of the resistive direct current superconducting quantum interference device

Ya. S. Greenberg, G.S. Krivoy, H. Koch

Published Feb 15, 1997• 9 citations
Publisher

Abstract

Partly resistive superconducting quantum interference devices (RSQUIDs) are used in noise thermometry in the liquid helium temperature range. Here we analyze one type of RSQUID that has not been thoroughly investigated until now: the direct current biased with two Josephson junctions and a resistive part connected in series with the junctions and closed by a superconducting ring. The resistive shunted model of the Josephson junctions is used for the analysis. Two cases of the RSQUID ring inductance were analyzed: (i) negligibly small and (ii) small but finite inductance. The expressions for the low frequency output signal, the current–voltage (I–V) characteristics, and the current flowing through the resistive part are obtained. In the dependence of the output frequency versus the dc current passed through the resistive part often an offset is observed experimentally. This phenomenon can be explained as an influence of an asymmetry in the critical currents of the junctions.

DOI
10.1063/1.364057

Related papers

Thin-film resistive SQUIDS

G.S. Krivoy, H. Koch

Different all thin-film partly resistive superconducting quantum interference devices (RSQUIDs) for noise thermometry in the liquid helium temperature range were designed and investigated. Three different types of RSQUID were realised: (i) dc RSQUID, (ii) rf RSQUID, and (iii) RSQUID with two quantization loops (double RSQUID). Shunted tunnel junctions were used as weak links. The resistive parts have been made as a Cu thin film combined with Nb thin films either as a sandwich or a planar element. The devices using a rf pump have integrated rf coupling coils. Resistances of the resistive parts in the range from 2.69 /spl mu//spl Omega/ to 246 /spl mu//spl Omega/ were obtained. The output signal was /spl ap/50 /spl mu/V for the dc RSQUIDs, up to 80 /spl mu/V for the rf RSQUIDs, and up to 1.2 mV for the double RSQUIDs. The linear dependences of the output signal frequency versus a dc current passed through the resistive part were observed up to 40 MHz. The double RSQUIDS described have a clear advantage in the output signal compared to the other RSQUIDs.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•4 citations

Analysis of the current-voltage characteristic of the rf SQUID

Philippe Lethuillier

The electrical equations of a resonant circuit fed with a radio-frequency current and inductively coupled to a weakly superconducting loop have been derived. The current-voltage characteristic of the rf superconducting quantum interference device can then be calculated and studied as a function of the junction resistance or of the resonance frequency, enabling its behavior to be better understood. As shown by Kurkijärvi, the large positive slope of the steps and the rounding of the characteristic result from thermal noise. However, in order to explain quantitatively the experimental results concerning, namely, point contact weak links which are generally oxidized or which have several contact points, it is useful to remark that the connection between the two superconductors constituting the Josephson junction may be made from n resistive paths. The mean thermal energy of the fluctuating flux is then close to nkbT instead of kbT if the inductances linking the contact points are large enough, that is, on the order of 10−11 H.

Journal of Applied Physics•Jun 1, 1993•0 citations

Influence of the Josephson junction on the impedance and noise of a resistive superconductive quantum interference device

Robert J. Soulen, William E. Fogle, Jack H. Colwell +2 more

The impedance and noise of a resistive superconductive quantum interference device (R-SQUID) have been measured as a function of the dc and rf currents applied to it. The Josephson junction was adjustable so that data were also taken for several values of the junction critical current. The results were compared with the predictions of a resistively shunted junction (RSJ) model which takes into account the influence of the Josephson junction on the impedance and noise. The agreement was found to be quite good and demonstrates that the noise in the circuit is well understood. Use of the R-SQUID as a noise thermometer below 1 K is assessed in terms of corrections due to the RSJ model. It is demonstrated how the dc and rf currents may be adjusted so that the total noise of the R-SQUID is reduced to within 0.1% of the Johnson noise generated by the resistor alone. Under these conditions, the R-SQUID may be used as a noise thermometer to determine thermodynamic temperature to this inaccuracy from 6 to 700 mK.

Journal of Applied Physics•Oct 15, 1993•4 citations

Asymmetry in the LC resonance characteristic in dc superconducting quantum interference devices: New method of observing pair-quasiparticle interference in superconducting tunnel junctions

Y. Song

The $\mathrm{LC}$ (inductance-capacitance) resonance phenomenon in the dc SQUID (superconducting quantum interference device) creates a current peak in the $I\ensuremath{-}V$ characteristics at a voltage determined by the resonance frequency. These $I\ensuremath{-}V$ characteristics have been analyzed with the resistively shunted Josephson-junction model in the low-damping and small-oscillation regime. The resonance $I\ensuremath{-}V$ characteristics contain sufficient information to determine all circuit parameters for the dc SQUID's. Specifically, we can apply this analysis to symmetric, tunnel-junction dc SQUID's to deduce the pair-quasiparticle interference conductance ($cos\ensuremath{\theta}$ term).

Physical review. B, Condensed matter•Sep 1, 1981•0 citations

Characteristics of asymmetric superconducting quantum interference devices

G. Testa, E. Sarnelli, S. Pagano +2 more

Direct current-superconducting quantum interference devices (SQUIDs) characterized by asymmetric Josephson junctions have never been used for applications. In order to demonstrate their potential advantages, a throughout numerical analysis of different asymmetric configurations has been carried out. A damping resistance has been included in the SQUID circuit and the thermal noise associated with junction and damping resistances has been considered in the numerical model. Magnetic modulations and flux noise spectral densities have been computed as a function of many parameters (bias current, asymmetry, SQUID inductance, and damping resistance) and the performance of symmetric and asymmetric devices have been compared. The results show that, by properly optimizing the SQUID design, asymmetric SQUIDs are characterized by higher magnetic flux to voltage transfer coefficient and lower flux noise. As a result, asymmetric configurations can be very useful in all the applications where high sensitivity is required.

Journal of Applied Physics•May 1, 2001•15 citations

Flicker (1∕f) noise in the critical current of Josephson junctions at 0.09–4.2K

F. C. Wellstood, C. Urbina, John L. Clarke

We have measured the low-frequency noise in the critical current Ic of six dc superconducting quantum interference devices (SQUIDs) with resistively shunted Nb–NbOx–PbIn Josephson junctions in the temperature range T=0.09–4.2K. Each device is voltage biased, the applied flux is an integer number of flux quanta, and the current fluctuations are measured with a second dc SQUID. At low frequencies f, there is a component of the power spectrum of the critical current fluctuations given approximately by SIc(f)=CIc2T2∕Af, where A is the area of both junctions, and C≈(3.9±0.4)×10−23m2∕K2. For quantum bits based on Josephson junctions, the scaling of SIc(f) with T2 implies that the dephasing time limited by critical current l∕f noise should scale as 1∕T for temperatures down to at least 0.09K.

Applied Physics Letters•Nov 29, 2004•63 citations
Partly resistive superconducting quantum interference devices (RSQUIDs) are used in noise thermometry in the liquid helium temperature range. Here we analyze one type of RSQUID that has not been thoroughly investigated until now: the direct current biased with two Josephson junctions and a resistive part connected in series with the junctions and closed by a superconducting ring. The resistive shunted model of the Josephson junctions is used for the analysis. Two cases of the RSQUID ring inductance were analyzed: (i) negligibly small and (ii) small but finite inductance. The expressions for the low frequency output signal, the current–voltage (I–V) characteristics, and the current flowing through the resistive part are obtained. In the dependence of the output frequency versus the dc current passed through the resistive part often an offset is observed experimentally. This phenomenon can be explained as an influence of an asymmetry in the critical currents of the junctions.
Different all thin-film partly resistive superconducting quantum interference devices (RSQUIDs) for noise thermometry in the liquid helium temperature range were designed and investigated. Three different types of RSQUID were realised: (i) dc RSQUID, (ii) rf RSQUID, and (iii) RSQUID with two quantization loops (double RSQUID). Shunted tunnel junctions were used as weak links. The resistive parts have been made as a Cu thin film combined with Nb thin films either as a sandwich or a planar element. The devices using a rf pump have integrated rf coupling coils. Resistances of the resistive parts in the range from 2.69 /spl mu//spl Omega/ to 246 /spl mu//spl Omega/ were obtained. The output signal was /spl ap/50 /spl mu/V for the dc RSQUIDs, up to 80 /spl mu/V for the rf RSQUIDs, and up to 1.2 mV for the double RSQUIDs. The linear dependences of the output signal frequency versus a dc current passed through the resistive part were observed up to 40 MHz. The double RSQUIDS described have a clear advantage in the output signal compared to the other RSQUIDs.>
The electrical equations of a resonant circuit fed with a radio-frequency current and inductively coupled to a weakly superconducting loop have been derived. The current-voltage characteristic of the rf superconducting quantum interference device can then be calculated and studied as a function of the junction resistance or of the resonance frequency, enabling its behavior to be better understood. As shown by Kurkijärvi, the large positive slope of the steps and the rounding of the characteristic result from thermal noise. However, in order to explain quantitatively the experimental results concerning, namely, point contact weak links which are generally oxidized or which have several contact points, it is useful to remark that the connection between the two superconductors constituting the Josephson junction may be made from n resistive paths. The mean thermal energy of the fluctuating flux is then close to nkbT instead of kbT if the inductances linking the contact points are large enough, that is, on the order of 10−11 H.
The impedance and noise of a resistive superconductive quantum interference device (R-SQUID) have been measured as a function of the dc and rf currents applied to it. The Josephson junction was adjustable so that data were also taken for several values of the junction critical current. The results were compared with the predictions of a resistively shunted junction (RSJ) model which takes into account the influence of the Josephson junction on the impedance and noise. The agreement was found to be quite good and demonstrates that the noise in the circuit is well understood. Use of the R-SQUID as a noise thermometer below 1 K is assessed in terms of corrections due to the RSJ model. It is demonstrated how the dc and rf currents may be adjusted so that the total noise of the R-SQUID is reduced to within 0.1% of the Johnson noise generated by the resistor alone. Under these conditions, the R-SQUID may be used as a noise thermometer to determine thermodynamic temperature to this inaccuracy from 6 to 700 mK.
The LC\mathrm{LC}LC (inductance-capacitance) resonance phenomenon in the dc SQUID (superconducting quantum interference device) creates a current peak in the $I\ensuremath{-}V$ characteristics at a voltage determined by the resonance frequency. These $I\ensuremath{-}V$ characteristics have been analyzed with the resistively shunted Josephson-junction model in the low-damping and small-oscillation regime. The resonance $I\ensuremath{-}V$ characteristics contain sufficient information to determine all circuit parameters for the dc SQUID's. Specifically, we can apply this analysis to symmetric, tunnel-junction dc SQUID's to deduce the pair-quasiparticle interference conductance ($cos\ensuremath{\theta}$ term).
Direct current-superconducting quantum interference devices (SQUIDs) characterized by asymmetric Josephson junctions have never been used for applications. In order to demonstrate their potential advantages, a throughout numerical analysis of different asymmetric configurations has been carried out. A damping resistance has been included in the SQUID circuit and the thermal noise associated with junction and damping resistances has been considered in the numerical model. Magnetic modulations and flux noise spectral densities have been computed as a function of many parameters (bias current, asymmetry, SQUID inductance, and damping resistance) and the performance of symmetric and asymmetric devices have been compared. The results show that, by properly optimizing the SQUID design, asymmetric SQUIDs are characterized by higher magnetic flux to voltage transfer coefficient and lower flux noise. As a result, asymmetric configurations can be very useful in all the applications where high sensitivity is required.
We have measured the low-frequency noise in the critical current Ic of six dc superconducting quantum interference devices (SQUIDs) with resistively shunted Nb–NbOx–PbIn Josephson junctions in the temperature range T=0.09–4.2K. Each device is voltage biased, the applied flux is an integer number of flux quanta, and the current fluctuations are measured with a second dc SQUID. At low frequencies f, there is a component of the power spectrum of the critical current fluctuations given approximately by SIc(f)=CIc2T2∕Af, where A is the area of both junctions, and C≈(3.9±0.4)×10−23m2∕K2. For quantum bits based on Josephson junctions, the scaling of SIc(f) with T2 implies that the dephasing time limited by critical current l∕f noise should scale as 1∕T for temperatures down to at least 0.09K.