Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Superconducting quantum interference device amplifiers at gigahertz frequencies

Michael Mück, Christian Welzel, John L. Clarke

Published May 8, 2003• 48 citations
Publisher

Abstract

A series of five dc superconducting quantum interference devices (SQUIDs) have been operated as microstrip amplifiers at frequencies ranging from 2.2 to 7.4 GHz. In these devices, the signal is connected between the SQUID washer and coil, which acts as a microstrip resonator. The gain measured at 4.2 K ranged from 12±1 to 6±1 dB. The noise temperature of three devices at 4.2 K in the frequency range 2.2–4 GHz was between 1 and 2 K, and the saturation temperature was between 150 and 250 K. Applications of these devices include readout for axion detectors, and intermediate-frequency amplifiers for superconductor–insulator–superconductor and hot-electron bolometer mixers.

DOI
10.1063/1.1572970

Related papers

Microstrip superconducting quantum interference device amplifier: Operation in higher-order modes

Michael Mück, Bernd Schmidt, John L. Clarke

DC Superconducting Quantum Interference Devices (SQUIDs) are widely used to amplify low-level, radio frequency (rf) electrical signals. SQUID amplifiers offer low noise, high gain, and low power dissipation. One method of implementing a SQUID rf amplifier for frequencies from a few hundred megahertz to several gigahertz is to operate the integrated input coil on top of the SQUID washer as a microstrip resonator. This is achieved by applying the input signal between one end of the coil and the SQUID washer, which acts as a groundplane; the other end of the coil is left open. Substantial levels of gain can be achieved from the microstrip SQUID amplifier for a signal frequency at the fundamental resonant frequency of the microstrip, at which the length of the microstrip is equal to one-half wavelength, λ/2. Since the length of the microstrip has to be made shorter for higher frequencies, however, the mutual inductance between a SQUID with a given geometry and the microstrip—and thus the gain—decreases with increasing frequency. We show that a significantly enhanced gain can be achieved by operating the microstrip resonator in higher-order modes, for example, with a microstrip length of 3λ/2 or 5λ/2, provided the winding sense of the microstrip for each consecutive λ/2 section is reversed. For a 4λ/2 resonator, we demonstrate a gain of 24 dB at 2.6 GHz, an increase in gain of about 10 dB compared to a λ/2 resonator on a SQUID of the same geometry and characteristics.

Applied Physics Letters•Jul 24, 2017•5 citations

Radio-frequency amplifier based on a niobium dc superconducting quantum interference device with microstrip input coupling

Michael Mück, Marc-Olivier André, John L. Clarke +2 more

A dc superconducting quantum interference device (SQUID) was used to amplify radio-frequency signals that were coupled to one end of the microstrip formed by the input coil and the SQUID washer. For one device, the resonant frequency of the microstrip was increased from about 200 to 620 MHz by progressively shortening the length of the coil. At an operating temperature of 4.2 K, the gain was typically 18 dB, and the system noise temperature ranged from 0.5±0.3 K at 80 MHz to 3.0±0.7 K at 500 MHz.

Applied Physics Letters•Jun 1, 1998•99 citations

Microstrip superconducting quantum interference device amplifiers with submicron Josephson junctions: Enhanced gain at gigahertz frequencies

M. P. DeFeo, P. Bhupathi, K. Yu +4 more

We present measurements of an amplifier based on a dc superconducting quantum interference device (SQUID) with submicron Al–AlOx–Al Josephson junctions. The small junction size reduces their self-capacitance and allows for the use of relatively large resistive shunts while maintaining nonhysteretic operation. This leads to an enhancement of the SQUID transfer function compared to SQUIDs with micron-scale junctions. The device layout is modified from that of a conventional SQUID to allow for coupling signals into the amplifier with a substantial mutual inductance for a relatively short microstrip coil. Measurements at 310 mK exhibit gain of 32 dB at 1.55 GHz.

arXiv:1008.1036•Applied Physics Letters•Aug 30, 2010•11 citations

Superconducting quantum interference device as a near-quantum-limited amplifier at 0.5 GHz

Michael Mück, Jan B. Kycia, John L. Clarke

A dc superconducting quantum interference device (SQUID) with a resonant microstrip input is operated as an amplifier at temperatures down to 20 mK. A second SQUID is used as a postamplifier. Below about 100 mK, the noise temperature is 52±20 mK at 538 MHz, estimated from measurements of signal-to-noise ratio, and 47±10 mK at 519 MHz, estimated from the noise generated by a resonant circuit coupled to the input. The quantum-limited noise temperatures are 26 and 25 mK, respectively. The measured noise temperature is limited by hot electrons generated by the bias current.

Applied Physics Letters•Feb 12, 2001•119 citations

Microstrip Superconducting Quantum Interference Device Amplifiers with Submicron Josephson Junctions: Enhanced Gain at Gigahertz Frequencies

Plourde, Britton, M. P. DeFeo, P. Bhupathi +2 more

We present measurements of an amplifier based on a dc superconducting quantum interference device (SQUID) with submicron Al-AlOx-Al Josephson junctions. The small junction size reduces their self-capacitance and allows for the use of relatively large resistive shunts while maintaining nonhysteretic operation. This leads to an enhancement of the SQUID transfer function compared to SQUIDs with micron-scale junctions. The device layout is modified from that of a conventional SQUID to allow for coupling signals into the amplifier with a substantial mutual inductance for a relatively short microstrip coil. Measurements at 310 mK exhibit gain of 32 dB at 1.55 GHz.

•Aug 5, 2010•9 citations

Microstrip direct current superconducting quantum interference device radio frequency amplifier: Noise data

Bernd Schmidt, Michael Mück

A series of about twenty superconducting quantum interference devices (SQUIDs) has been operated as microstrip-SQUID amplifiers (MSAs) at frequencies ranging from 100 MHz to 2 GHz to study the dependence of their gain and noise temperature on bias current and flux. The measured values were in good agreement with theory. The observed dependence of MSA gain and noise temperature on bias current and flux resembled the static transfer function of the SQUIDs. The gains are relatively insensitive to changes in bias current and bias flux; the noise temperature is strongly dependent on the bias flux.

Applied Physics Letters•Apr 9, 2012•0 citations
A series of five dc superconducting quantum interference devices (SQUIDs) have been operated as microstrip amplifiers at frequencies ranging from 2.2 to 7.4 GHz. In these devices, the signal is connected between the SQUID washer and coil, which acts as a microstrip resonator. The gain measured at 4.2 K ranged from 12±1 to 6±1 dB. The noise temperature of three devices at 4.2 K in the frequency range 2.2–4 GHz was between 1 and 2 K, and the saturation temperature was between 150 and 250 K. Applications of these devices include readout for axion detectors, and intermediate-frequency amplifiers for superconductor–insulator–superconductor and hot-electron bolometer mixers.
DC Superconducting Quantum Interference Devices (SQUIDs) are widely used to amplify low-level, radio frequency (rf) electrical signals. SQUID amplifiers offer low noise, high gain, and low power dissipation. One method of implementing a SQUID rf amplifier for frequencies from a few hundred megahertz to several gigahertz is to operate the integrated input coil on top of the SQUID washer as a microstrip resonator. This is achieved by applying the input signal between one end of the coil and the SQUID washer, which acts as a groundplane; the other end of the coil is left open. Substantial levels of gain can be achieved from the microstrip SQUID amplifier for a signal frequency at the fundamental resonant frequency of the microstrip, at which the length of the microstrip is equal to one-half wavelength, λ/2. Since the length of the microstrip has to be made shorter for higher frequencies, however, the mutual inductance between a SQUID with a given geometry and the microstrip—and thus the gain—decreases with increasing frequency. We show that a significantly enhanced gain can be achieved by operating the microstrip resonator in higher-order modes, for example, with a microstrip length of 3λ/2 or 5λ/2, provided the winding sense of the microstrip for each consecutive λ/2 section is reversed. For a 4λ/2 resonator, we demonstrate a gain of 24 dB at 2.6 GHz, an increase in gain of about 10 dB compared to a λ/2 resonator on a SQUID of the same geometry and characteristics.
A dc superconducting quantum interference device (SQUID) was used to amplify radio-frequency signals that were coupled to one end of the microstrip formed by the input coil and the SQUID washer. For one device, the resonant frequency of the microstrip was increased from about 200 to 620 MHz by progressively shortening the length of the coil. At an operating temperature of 4.2 K, the gain was typically 18 dB, and the system noise temperature ranged from 0.5±0.3 K at 80 MHz to 3.0±0.7 K at 500 MHz.
We present measurements of an amplifier based on a dc superconducting quantum interference device (SQUID) with submicron Al–AlOx–Al Josephson junctions. The small junction size reduces their self-capacitance and allows for the use of relatively large resistive shunts while maintaining nonhysteretic operation. This leads to an enhancement of the SQUID transfer function compared to SQUIDs with micron-scale junctions. The device layout is modified from that of a conventional SQUID to allow for coupling signals into the amplifier with a substantial mutual inductance for a relatively short microstrip coil. Measurements at 310 mK exhibit gain of 32 dB at 1.55 GHz.
A dc superconducting quantum interference device (SQUID) with a resonant microstrip input is operated as an amplifier at temperatures down to 20 mK. A second SQUID is used as a postamplifier. Below about 100 mK, the noise temperature is 52±20 mK at 538 MHz, estimated from measurements of signal-to-noise ratio, and 47±10 mK at 519 MHz, estimated from the noise generated by a resonant circuit coupled to the input. The quantum-limited noise temperatures are 26 and 25 mK, respectively. The measured noise temperature is limited by hot electrons generated by the bias current.
We present measurements of an amplifier based on a dc superconducting quantum interference device (SQUID) with submicron Al-AlOx-Al Josephson junctions. The small junction size reduces their self-capacitance and allows for the use of relatively large resistive shunts while maintaining nonhysteretic operation. This leads to an enhancement of the SQUID transfer function compared to SQUIDs with micron-scale junctions. The device layout is modified from that of a conventional SQUID to allow for coupling signals into the amplifier with a substantial mutual inductance for a relatively short microstrip coil. Measurements at 310 mK exhibit gain of 32 dB at 1.55 GHz.
A series of about twenty superconducting quantum interference devices (SQUIDs) has been operated as microstrip-SQUID amplifiers (MSAs) at frequencies ranging from 100 MHz to 2 GHz to study the dependence of their gain and noise temperature on bias current and flux. The measured values were in good agreement with theory. The observed dependence of MSA gain and noise temperature on bias current and flux resembled the static transfer function of the SQUIDs. The gains are relatively insensitive to changes in bias current and bias flux; the noise temperature is strongly dependent on the bias flux.