Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Microstrip direct current superconducting quantum interference device radio frequency amplifier: Noise data

Bernd Schmidt, Michael Mück

Published Apr 9, 2012• 0 citations
Publisher

Abstract

A series of about twenty superconducting quantum interference devices (SQUIDs) has been operated as microstrip-SQUID amplifiers (MSAs) at frequencies ranging from 100 MHz to 2 GHz to study the dependence of their gain and noise temperature on bias current and flux. The measured values were in good agreement with theory. The observed dependence of MSA gain and noise temperature on bias current and flux resembled the static transfer function of the SQUIDs. The gains are relatively insensitive to changes in bias current and bias flux; the noise temperature is strongly dependent on the bias flux.

DOI
10.1063/1.3702825

Related papers

Radio-frequency amplifier with tenth-kelvin noise temperature based on a microstrip direct current superconducting quantum interference device

Marc-Olivier André, Michael Mück, John L. Clarke +2 more

A dc superconducting quantum interference device (SQUID) with a resonant microstrip input and a cooled heterostructure field-effect transistor as a postamplifier is used as a radio-frequency amplifier in the frequency range 90–500 MHz. At liquid He3 temperatures, gains of 24 and 20 dB and intrinsic noise temperatures of 0.06±0.02 and 0.12±0.10 K were achieved at 89.6 and 438 MHz, respectively. The system noise temperature at 438 MHz was also estimated from the Nyquist noise produced by a resonant circuit coupled to the input of the microstrip SQUID.

Applied Physics Letters•Aug 2, 1999•38 citations

Superconducting quantum interference device amplifiers at gigahertz frequencies

Michael Mück, Christian Welzel, John L. Clarke

A series of five dc superconducting quantum interference devices (SQUIDs) have been operated as microstrip amplifiers at frequencies ranging from 2.2 to 7.4 GHz. In these devices, the signal is connected between the SQUID washer and coil, which acts as a microstrip resonator. The gain measured at 4.2 K ranged from 12±1 to 6±1 dB. The noise temperature of three devices at 4.2 K in the frequency range 2.2–4 GHz was between 1 and 2 K, and the saturation temperature was between 150 and 250 K. Applications of these devices include readout for axion detectors, and intermediate-frequency amplifiers for superconductor–insulator–superconductor and hot-electron bolometer mixers.

Applied Physics Letters•May 8, 2003•48 citations

Radio-frequency amplifier based on a niobium dc superconducting quantum interference device with microstrip input coupling

Michael Mück, Marc-Olivier André, John L. Clarke +2 more

A dc superconducting quantum interference device (SQUID) was used to amplify radio-frequency signals that were coupled to one end of the microstrip formed by the input coil and the SQUID washer. For one device, the resonant frequency of the microstrip was increased from about 200 to 620 MHz by progressively shortening the length of the coil. At an operating temperature of 4.2 K, the gain was typically 18 dB, and the system noise temperature ranged from 0.5±0.3 K at 80 MHz to 3.0±0.7 K at 500 MHz.

Applied Physics Letters•Jun 1, 1998•99 citations

Superconducting quantum interference device as a near-quantum-limited amplifier at 0.5 GHz

Michael Mück, Jan B. Kycia, John L. Clarke

A dc superconducting quantum interference device (SQUID) with a resonant microstrip input is operated as an amplifier at temperatures down to 20 mK. A second SQUID is used as a postamplifier. Below about 100 mK, the noise temperature is 52±20 mK at 538 MHz, estimated from measurements of signal-to-noise ratio, and 47±10 mK at 519 MHz, estimated from the noise generated by a resonant circuit coupled to the input. The quantum-limited noise temperatures are 26 and 25 mK, respectively. The measured noise temperature is limited by hot electrons generated by the bias current.

Applied Physics Letters•Feb 12, 2001•119 citations

Microstrip superconducting quantum interference device radio-frequency amplifier: Tuning and cascading

Michael Mück, Marc-Olivier André, John L. Clarke +2 more

The resonant frequency of an amplifier based on a low-temperature dc superconducting quantum interference device (SQUID) is tuned by varying the capacitance across the end of the input microstrip by means of a varactor diode. The resonant frequency can be reduced substantially, for example, from 190 to 110 MHz, while maintaining an on-resonance gain of 27–28 dB. Two microstrip SQUID amplifiers with the same resonant frequency are cascaded to achieve a gain of 33.5±1 dB at 386 MHz; with the SQUIDs tuned to different frequencies, the gain is 22 dB or higher from about 260 to 420 MHz.

Applied Physics Letters•Nov 29, 1999•37 citations

Flux-bias stabilization scheme for a radio-frequency amplifier based on a superconducting quantum interference device

Michael Mück, John L. Clarke

A magnetic flux stabilization scheme involving a low-frequency flux-locked loop has been developed to regulate the gain of a radio-frequency amplifier based on a superconducting quantum inteference device (SQUID). The flux-locked loop largely eliminates drifts in the gain arising from drifts in the flux bias. Tests on a microstrip SQUID amplifier operating at 777 MHz inside a superconducting shield show that the peak-to-peak drift in the gain is no more than 0.3 dB/day.

Review of Scientific Instruments•Sep 1, 2001•9 citations
A series of about twenty superconducting quantum interference devices (SQUIDs) has been operated as microstrip-SQUID amplifiers (MSAs) at frequencies ranging from 100 MHz to 2 GHz to study the dependence of their gain and noise temperature on bias current and flux. The measured values were in good agreement with theory. The observed dependence of MSA gain and noise temperature on bias current and flux resembled the static transfer function of the SQUIDs. The gains are relatively insensitive to changes in bias current and bias flux; the noise temperature is strongly dependent on the bias flux.
A dc superconducting quantum interference device (SQUID) with a resonant microstrip input and a cooled heterostructure field-effect transistor as a postamplifier is used as a radio-frequency amplifier in the frequency range 90–500 MHz. At liquid He3 temperatures, gains of 24 and 20 dB and intrinsic noise temperatures of 0.06±0.02 and 0.12±0.10 K were achieved at 89.6 and 438 MHz, respectively. The system noise temperature at 438 MHz was also estimated from the Nyquist noise produced by a resonant circuit coupled to the input of the microstrip SQUID.
A series of five dc superconducting quantum interference devices (SQUIDs) have been operated as microstrip amplifiers at frequencies ranging from 2.2 to 7.4 GHz. In these devices, the signal is connected between the SQUID washer and coil, which acts as a microstrip resonator. The gain measured at 4.2 K ranged from 12±1 to 6±1 dB. The noise temperature of three devices at 4.2 K in the frequency range 2.2–4 GHz was between 1 and 2 K, and the saturation temperature was between 150 and 250 K. Applications of these devices include readout for axion detectors, and intermediate-frequency amplifiers for superconductor–insulator–superconductor and hot-electron bolometer mixers.
A dc superconducting quantum interference device (SQUID) was used to amplify radio-frequency signals that were coupled to one end of the microstrip formed by the input coil and the SQUID washer. For one device, the resonant frequency of the microstrip was increased from about 200 to 620 MHz by progressively shortening the length of the coil. At an operating temperature of 4.2 K, the gain was typically 18 dB, and the system noise temperature ranged from 0.5±0.3 K at 80 MHz to 3.0±0.7 K at 500 MHz.
A dc superconducting quantum interference device (SQUID) with a resonant microstrip input is operated as an amplifier at temperatures down to 20 mK. A second SQUID is used as a postamplifier. Below about 100 mK, the noise temperature is 52±20 mK at 538 MHz, estimated from measurements of signal-to-noise ratio, and 47±10 mK at 519 MHz, estimated from the noise generated by a resonant circuit coupled to the input. The quantum-limited noise temperatures are 26 and 25 mK, respectively. The measured noise temperature is limited by hot electrons generated by the bias current.
The resonant frequency of an amplifier based on a low-temperature dc superconducting quantum interference device (SQUID) is tuned by varying the capacitance across the end of the input microstrip by means of a varactor diode. The resonant frequency can be reduced substantially, for example, from 190 to 110 MHz, while maintaining an on-resonance gain of 27–28 dB. Two microstrip SQUID amplifiers with the same resonant frequency are cascaded to achieve a gain of 33.5±1 dB at 386 MHz; with the SQUIDs tuned to different frequencies, the gain is 22 dB or higher from about 260 to 420 MHz.