Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1206.2235 · Applied Physics Letters

Superconducting microstrip amplifiers with sub-Kelvin noise temperature near 4 GHz

M. P. DeFeo, B. L. T. Plourde

Published Jul 30, 2012• 12 citations
arXivHTMLPDF

Abstract

We present measurements of an amplifier operating at 3.8 GHz with 150 MHz of bandwidth based on the microstrip input-coil resonance of a dc superconducting quantum interference device (SQUID) with submicron Josephson junctions. The noise temperature is measured using two methods: comparing the signal-to-noise ratio of the system with and without the SQUID in the amplifier chain, and using a modified Y-factor technique where calibrated narrowband noise is mixed up to the SQUID amplifier operating frequency. With the SQUID cooled to 0.35 K, we observe a minimum system noise temperature of 0.55 ± 0.13 K, dominated by the contribution from the SQUID amplifier.

DOI
10.1063/1.4742164

Related papers

Superconducting quantum interference device as a near-quantum-limited amplifier at 0.5 GHz

Michael Mück, Jan B. Kycia, John L. Clarke

A dc superconducting quantum interference device (SQUID) with a resonant microstrip input is operated as an amplifier at temperatures down to 20 mK. A second SQUID is used as a postamplifier. Below about 100 mK, the noise temperature is 52±20 mK at 538 MHz, estimated from measurements of signal-to-noise ratio, and 47±10 mK at 519 MHz, estimated from the noise generated by a resonant circuit coupled to the input. The quantum-limited noise temperatures are 26 and 25 mK, respectively. The measured noise temperature is limited by hot electrons generated by the bias current.

Applied Physics Letters•Feb 12, 2001•119 citations

Radio-frequency amplifier with tenth-kelvin noise temperature based on a microstrip direct current superconducting quantum interference device

Marc-Olivier André, Michael Mück, John L. Clarke +2 more

A dc superconducting quantum interference device (SQUID) with a resonant microstrip input and a cooled heterostructure field-effect transistor as a postamplifier is used as a radio-frequency amplifier in the frequency range 90–500 MHz. At liquid He3 temperatures, gains of 24 and 20 dB and intrinsic noise temperatures of 0.06±0.02 and 0.12±0.10 K were achieved at 89.6 and 438 MHz, respectively. The system noise temperature at 438 MHz was also estimated from the Nyquist noise produced by a resonant circuit coupled to the input of the microstrip SQUID.

Applied Physics Letters•Aug 2, 1999•38 citations

Radio-frequency amplifier based on a niobium dc superconducting quantum interference device with microstrip input coupling

Michael Mück, Marc-Olivier André, John L. Clarke +2 more

A dc superconducting quantum interference device (SQUID) was used to amplify radio-frequency signals that were coupled to one end of the microstrip formed by the input coil and the SQUID washer. For one device, the resonant frequency of the microstrip was increased from about 200 to 620 MHz by progressively shortening the length of the coil. At an operating temperature of 4.2 K, the gain was typically 18 dB, and the system noise temperature ranged from 0.5±0.3 K at 80 MHz to 3.0±0.7 K at 500 MHz.

Applied Physics Letters•Jun 1, 1998•99 citations

Superconducting quantum interference device amplifiers at gigahertz frequencies

Michael Mück, Christian Welzel, John L. Clarke

A series of five dc superconducting quantum interference devices (SQUIDs) have been operated as microstrip amplifiers at frequencies ranging from 2.2 to 7.4 GHz. In these devices, the signal is connected between the SQUID washer and coil, which acts as a microstrip resonator. The gain measured at 4.2 K ranged from 12±1 to 6±1 dB. The noise temperature of three devices at 4.2 K in the frequency range 2.2–4 GHz was between 1 and 2 K, and the saturation temperature was between 150 and 250 K. Applications of these devices include readout for axion detectors, and intermediate-frequency amplifiers for superconductor–insulator–superconductor and hot-electron bolometer mixers.

Applied Physics Letters•May 8, 2003•48 citations

Microstrip superconducting quantum interference device amplifiers with submicron Josephson junctions: Enhanced gain at gigahertz frequencies

M. P. DeFeo, P. Bhupathi, K. Yu +4 more

We present measurements of an amplifier based on a dc superconducting quantum interference device (SQUID) with submicron Al–AlOx–Al Josephson junctions. The small junction size reduces their self-capacitance and allows for the use of relatively large resistive shunts while maintaining nonhysteretic operation. This leads to an enhancement of the SQUID transfer function compared to SQUIDs with micron-scale junctions. The device layout is modified from that of a conventional SQUID to allow for coupling signals into the amplifier with a substantial mutual inductance for a relatively short microstrip coil. Measurements at 310 mK exhibit gain of 32 dB at 1.55 GHz.

arXiv:1008.1036•Applied Physics Letters•Aug 30, 2010•11 citations

Microstrip Superconducting Quantum Interference Device Amplifiers with Submicron Josephson Junctions: Enhanced Gain at Gigahertz Frequencies

Plourde, Britton, M. P. DeFeo, P. Bhupathi +2 more

We present measurements of an amplifier based on a dc superconducting quantum interference device (SQUID) with submicron Al-AlOx-Al Josephson junctions. The small junction size reduces their self-capacitance and allows for the use of relatively large resistive shunts while maintaining nonhysteretic operation. This leads to an enhancement of the SQUID transfer function compared to SQUIDs with micron-scale junctions. The device layout is modified from that of a conventional SQUID to allow for coupling signals into the amplifier with a substantial mutual inductance for a relatively short microstrip coil. Measurements at 310 mK exhibit gain of 32 dB at 1.55 GHz.

•Aug 5, 2010•9 citations
We present measurements of an amplifier operating at 3.8 GHz with 150 MHz of bandwidth based on the microstrip input-coil resonance of a dc superconducting quantum interference device (SQUID) with submicron Josephson junctions. The noise temperature is measured using two methods: comparing the signal-to-noise ratio of the system with and without the SQUID in the amplifier chain, and using a modified Y-factor technique where calibrated narrowband noise is mixed up to the SQUID amplifier operating frequency. With the SQUID cooled to 0.35 K, we observe a minimum system noise temperature of 0.55 ± 0.13 K, dominated by the contribution from the SQUID amplifier.
A dc superconducting quantum interference device (SQUID) with a resonant microstrip input is operated as an amplifier at temperatures down to 20 mK. A second SQUID is used as a postamplifier. Below about 100 mK, the noise temperature is 52±20 mK at 538 MHz, estimated from measurements of signal-to-noise ratio, and 47±10 mK at 519 MHz, estimated from the noise generated by a resonant circuit coupled to the input. The quantum-limited noise temperatures are 26 and 25 mK, respectively. The measured noise temperature is limited by hot electrons generated by the bias current.
A dc superconducting quantum interference device (SQUID) with a resonant microstrip input and a cooled heterostructure field-effect transistor as a postamplifier is used as a radio-frequency amplifier in the frequency range 90–500 MHz. At liquid He3 temperatures, gains of 24 and 20 dB and intrinsic noise temperatures of 0.06±0.02 and 0.12±0.10 K were achieved at 89.6 and 438 MHz, respectively. The system noise temperature at 438 MHz was also estimated from the Nyquist noise produced by a resonant circuit coupled to the input of the microstrip SQUID.
A dc superconducting quantum interference device (SQUID) was used to amplify radio-frequency signals that were coupled to one end of the microstrip formed by the input coil and the SQUID washer. For one device, the resonant frequency of the microstrip was increased from about 200 to 620 MHz by progressively shortening the length of the coil. At an operating temperature of 4.2 K, the gain was typically 18 dB, and the system noise temperature ranged from 0.5±0.3 K at 80 MHz to 3.0±0.7 K at 500 MHz.
A series of five dc superconducting quantum interference devices (SQUIDs) have been operated as microstrip amplifiers at frequencies ranging from 2.2 to 7.4 GHz. In these devices, the signal is connected between the SQUID washer and coil, which acts as a microstrip resonator. The gain measured at 4.2 K ranged from 12±1 to 6±1 dB. The noise temperature of three devices at 4.2 K in the frequency range 2.2–4 GHz was between 1 and 2 K, and the saturation temperature was between 150 and 250 K. Applications of these devices include readout for axion detectors, and intermediate-frequency amplifiers for superconductor–insulator–superconductor and hot-electron bolometer mixers.
We present measurements of an amplifier based on a dc superconducting quantum interference device (SQUID) with submicron Al–AlOx–Al Josephson junctions. The small junction size reduces their self-capacitance and allows for the use of relatively large resistive shunts while maintaining nonhysteretic operation. This leads to an enhancement of the SQUID transfer function compared to SQUIDs with micron-scale junctions. The device layout is modified from that of a conventional SQUID to allow for coupling signals into the amplifier with a substantial mutual inductance for a relatively short microstrip coil. Measurements at 310 mK exhibit gain of 32 dB at 1.55 GHz.
We present measurements of an amplifier based on a dc superconducting quantum interference device (SQUID) with submicron Al-AlOx-Al Josephson junctions. The small junction size reduces their self-capacitance and allows for the use of relatively large resistive shunts while maintaining nonhysteretic operation. This leads to an enhancement of the SQUID transfer function compared to SQUIDs with micron-scale junctions. The device layout is modified from that of a conventional SQUID to allow for coupling signals into the amplifier with a substantial mutual inductance for a relatively short microstrip coil. Measurements at 310 mK exhibit gain of 32 dB at 1.55 GHz.