The dynamics of the dc-SQUID in the presence of a signal coil was studied. The signal coil creates an additive parasitic capacitance between the junctions and its self-resonance imports new features to the SQUID dynamics. Our results suggest that if a SQUID with smooth characteristics and low noise properties is desired, all the resonances present in the SQUID ring or in the flux coupling circuit should be damped properly. Low attenuation yields a system with high gain but with higher excess noise. On the other hand, heavy damping of the device yields low gain and a high noise level and thus a compromise is necessary.
The dynamics of the dc-SQUID in the presence of a signal coil was studied. The signal coil creates an additive parasitic capacitance between the junctions and its self-resonance imports new features to the SQUID dynamics. Our results suggest that if a SQUID with smooth characteristics and low noise properties is desired, all the resonances present in the SQUID ring or in the flux coupling circuit should be damped properly. Low attenuation yields a system with high gain but with higher excess noise. On the other hand, heavy damping of the device yields low gain and a high noise level and thus a compromise is necessary.
We have fabricated and characterized the noise performance of well-coupled Nb-Pb alloy edge junction dc superconducting quantum interference devices (SQUIDs) with a resistively shunted inductance. The extra damping resistor removes the resonances in the current-voltage characteristics resulting in a very low value of the extrinsic energy sensitivity in flux-locked-loop operation. Numerical simulations, with the junction capacitance included, indicate that the damping resistance does not degrade noise performance until it is significantly less than the junction-shunting resistance. We also tested different SQUID designs and demonstrated that a large SQUID inductance, proposed earlier to be desirable when resistively shunted, can seriously affect the low-frequency flux noise.
Practical thin-film dc superconducting quantum interference devices (SQUIDs) are often built with an integrated input coil which leads to the formation of various parasitic elements. We have designed and fabricated several square washer-shaped dc SQUID test devices with various amounts of parasitic capacitance formed by covering the washer slits with superconducting coverplates of various widths. In the simplest approximation, the parasitic capacitance Cp appears entirely across the Josephson junctions; in a better approximation, Cp divides the total inductance into two parts, an effective SQUID loop inductance L and a small parasitic inductance Lp. For both models, noise-free and noise-rounded current-voltage and voltage-flux characteristics are calculated for various values of the ratios L/Lp and Cp/C, where C is the Josephson junction capacitance. The SQUID dynamics are significantly affected by Cp and Lp. The energy resolution ε at first deteriorates with increasing Cp for Cp/C ≲ 2, but as Cp/C becomes large, ε improves to less than twice the value for Cp/C ≊ 0. The optimal points of operation for large Cp, however, are found at voltages above the low-frequency resonance determined by L and Cp where the flux-to-voltage transfer function is low. Furthermore, for devices with Cp/C ≫ 1 and Lp≠0, the double-loop geometry leads to an additional resonance determined by Lp and C that appears at high frequencies. The energy resolution inside this high-frequency resonance is nearly independent of Cp and comparable to the energy resolution of a device having the same total inductance but with Cp/C ≪ 1. Extensive noise mappings on several different test devices have been carried out using a computer-controlled measurement system. The measured characteristics and noise performance are shown to be in good agreement with the simulations.
A low-noise coupled DC superconducting quantum interference device (SQUID) especially optimized for low frequency is discussed. Using large Josephson junctions and a low loop inductance the contribution of the critical current fluctuation to 1/f noise can be minimized. To minimize the inductance the Josephson junctions are placed in the center of the washer close to the SQUID loop. A scaled-up copper model of the SQUID and the signal coil is used to analyze the impedance of the SQUID loop affected by the signal coil. An equivalent circuit model describing the effective inductance of the SQUID loop as a function of the frequency is used to design appropriate damping of the resonances. The DC SQUID characteristics are smooth and the noise performance of the SQUID does not markedly suffer from resonances. The contribution of the 1/f noise at 1 Hz is found to be about 5*10/sup -7/ Phi /sub 0// square root Hz.>
The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.
The dynamics and noise of a dc superconducting quantum interference device (SQUID) with the McCumber parameter βc=2πR2IcC/Φ0 close to the unity (where Ic, R, C are the critical current, the shunt resistance, and the capacitance of the Josephson junctions comprising the SQUID, respectively, and Φ0=2.07×10−15 Wb is the magnetic flux quantum) integrated with a planar spiral input coil have been experimentally studied. The length of the spiral input coil was chosen to match its λ/4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance enhances the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, increases the dynamic resistance Rd and the gradient of the flux-to-voltage characteristics ∂V/∂Φ without hysteresis. This relaxes the tolerance for the βc parameter, simplifies the technological process, and improves the yield of devices. A dc SQUID with loop inductance L=31.4 pH, βc=0.72, and a six turn input coil has demonstrated a nondistorted quasisinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of approximately 140 μV peak-to-peak. A spectral density of the intrinsic magnetic flux noise as low as 3.5×10−7 Φ0/Hz1/2 has been measured in the double stage configuration at a temperature of 4.2 K using direct read-out electronics. This corresponds to the intrinsic energy resolution of ε=12.5h. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz1/2 with an input coil inductance of 58 nH. The coupled energy resolution is εc=45h in the white noise region.
tions of the device; in particular, variations in the critical current of small junctions can lead to significant lowfrequency noise [2]. In high-quality junctions, however, these fluctuations may be negligible. For the Stanford experiment, we require well-coupled ck SQUIDs with an energy sensitivity of 1 x lo-*’ J/Hz ai 5 mHz. Early in the development of these devices, we observed both excess low-frequency noise and resonances due to the input coil. (Our investigation of resonance phenomenon will be discussed elsewhere [3] and we focus on the excess low-frequency noise here.) To study the excess noise, we have fabricated devices with two geometries: a well-coupled SQUID with a washer geometry and a self-shielded SQUID with a stripline geometry [4, 51. Results of these experiments indicate that we are observing flux noise originating from within the SQUID. Process improvements have dramatically reduced this noise. We have also performed experiments to reduce the potential for flux motion in the SQUID; this work is still in progress.