Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Journal of Solid-State Circuits

AC-and DC-powered subnanosecond 1-kbit Josephson cache memory design

Y. Wada, Mutsuo Hidaka, Shuichi Nagasawa, Ichiro Ishida

Published Aug 1, 1988• 7 citations
Publisher

Abstract

The address decoders, address line drivers, and sense circuits of the fully decoded memory consist of resistor-coupled Josephson logic circuits to realize fast access. The memory cell is constructed from two three-junction symmetric SQUID (superconducting quantum interface device) gates, and a four-flux-quanta storage loop for enabling bipolar current drive. This memory configuration has intrinsic advantages in regard to magnetic flux trapping in address lines and a gate circuit latch-up problem over a DC-powered memory constructed from inductor coupled gates. Individual control and cell circuits were fabricated, using a lead-alloy process, and their operation was verified. A 570-ps read access time is estimated as the sum measured 280-ps decoding time, and calculated 130-ps address line current rising time, 110-ps sense time, and 50-ps signal propagation time. The 1-kb chip is designed to consume 9 mW without voltage regulators.>

DOI
10.1109/4.343

Related papers

A 2-kbit superconducting memory chip

Perng-Fei Yuh

A 2-kb nondestructive readout memory chip has been built using an Nb/AlO/sub x//Nb Josephson-junction process with a 2.5- mu m design rule. A bitmap of 56% functional cells among 1.5 K tested cells, a read access time of 200 ps, an average cycle time of 500 ps without the decoder, and a power dissipation of 1.6 mW including peripheral circuits have been obtained. The decoding time is estimated to be 540 ps. The circuits in this 5-mm by 5-mm, 24-pin chip includes 2 K memory cells, 6-b decoder and drivers, serial-to-parallel and parallel-to-serial converters, and circuits for design of testability or timing measurements. More than 14000 junctions are used on the chip.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1993•22 citations

Josephson-CMOS Hybrid Memories

Qingguo Liu, Qingguo Liu

Abstract : Lack of high-density, fast and memory has been a long-standing problem in superconducting digital electronics. Alternative Josephson-junction-based memory cells and peripheral circuits have intrinsic problems which impede the application of that kind of memory. The CMOS-Josephson hybrid memory idea was proposed in 1992 to circumvent this problem. In the present work we have designed and demonstrated a 64-kb CMOS-Josephson hybrid memory working at 1 GHz. In order to make the hybrid idea practical, a complete and comprehensive 4 K short-channel CMOS model for digital circuits was developed for this dissertation. It has been used in the design of the memory core and peripheral circuits. A fast hybrid interface circuit that transforms single-flux-quantum millivolt 2-ps pulse signals to CMOS volt-level signals has been studied and the optimized design has been completed. Using a nonvolatile cryogenic 3-T DRAM cell, the memory core is designed in such a way that the access time is much less than for room-temperature operation, not only because of the performance upgrade due to the temperature decrease but also because of a different reading mechanism. Fabricated by commercial submicron CMOS processes (0.25 microns and 0.18 microns) and a Nb/AlOx/Nb Josephson-junction process with 2.5 kA/cm2 tunneling current density, the memory chips were bonded together by direct wire-bonding and by flip-chip bump-bonding and tested at low frequencies, high frequencies, respectively. A subnanosecond access time is obtained both from simulations and experiments. The power for an interface circuit is measured to be 0.6 mW. The memory core consumes even less power. The total power consumption depends on the operation mode of the memory and is calculated to be 10 mW for reading and 28 mW for writing. Simulations also indicate that, with more advanced semiconductor and superconductor technologies, larger and faster hybrid memories are expected to be achievable in the future.

•Nov 7, 2013•4 citations

A 4K Josephson memory

Hideo Suzuki, Norio Fujimaki, Hirotaka Tamura +2 more

The authors describe the design and experimental performance of a 4 K*1-bit Josephson (RAM). For high-speed memory operation, the authors have developed a compact AND gate for the decoder, a high-voltage driver gate, and a capacitively coupled single-flux quantum memory cell. The 4 K memory was designed using these gates and cell and was fabricated with Nb/AlO/sub x//Nb junctions. The minimum access time was 590 ps, and the total power dissipation was 19 mW.>

IEEE Transactions on Magnetics•Mar 1, 1989•51 citations

Model for a 15 ns 16K RAM with Josephson junctions

Ronald F. Broom, Pierre Guéret, W. Kotyczka +4 more

An experimental memory model for investigating the feasibility of a 16K RAM memory with Josephson junctions was fabricated and tested. There are nearly 4500 Josephson junctions in the design which includes array, line drivers, and address decoders. Storage element is a single flux-quantum (SFQ) cell arranged in a 2K array. Drivers and decoders are based on the principle of current steering in superconducting loops, which is a medium speed but low power approach. The measured read-access time of the model is approximately 10 ns. Power dissipation of the unselected chip is zero, whereas for a read/write cycle time of 30 ns, it amounts to about 10 /spl mu/W. Results indicate that a 16K chip is feasible electrically. The estimated access time and power dissipation are 15 ns and 40 /spl nu/W, respectively.

IEEE Journal of Solid-State Circuits•Aug 1, 1979•47 citations

Pipelined DC-powered SFQ RAM

Alex F. Kirichenko, Saad M. Sarwana, DARREN K. BROCK +1 more

We present the design and test results of components for a superconductor Cryogenic Random Access Memory (CRAM). The 16-Kb RAM design consists of four 4-Kb sub-arrays (blocks) with a 400 ps access time (latency) and a 100 ps cycle time (throughput). Each 4-Kb RAM block comprises a row-accessed 32/spl times/128 memory cell array, bipolar line drivers, row decoders, and column sense circuits. The implementation of specially designed distributed Josephson junctions in the sensing circuits reduces the overall size of the blocks and allows the use of smaller dc control currents.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•26 citations

Investigations for a Josephson Computer Main Memory with Single-Flux-Quantum Cells

Pierre Guéret, A. Moser, P. Wolf

The paper first summarizes requirements for a main memory with Josephson junctions and reviews the work carried out on an experimental main memory model containing an array of single-flux-quantum cells, line drivers, and address decoders with a total of nearly 4500 Josephson junctions. In the second part, theoretical and experimental investigations on the y drive system, including sense circuit, are presented. The investigations deal with both the read and write phases. Finally, the on-chip logic circuits and the address decoders are discussed, and the experimental results presented. Drivers and decoders based on the principle of current steering in superconducting loops are intended to be used on a fully populated main-memory chip.

IBM Journal of Research and Development•Mar 1, 1980•28 citations
The address decoders, address line drivers, and sense circuits of the fully decoded memory consist of resistor-coupled Josephson logic circuits to realize fast access. The memory cell is constructed from two three-junction symmetric SQUID (superconducting quantum interface device) gates, and a four-flux-quanta storage loop for enabling bipolar current drive. This memory configuration has intrinsic advantages in regard to magnetic flux trapping in address lines and a gate circuit latch-up problem over a DC-powered memory constructed from inductor coupled gates. Individual control and cell circuits were fabricated, using a lead-alloy process, and their operation was verified. A 570-ps read access time is estimated as the sum measured 280-ps decoding time, and calculated 130-ps address line current rising time, 110-ps sense time, and 50-ps signal propagation time. The 1-kb chip is designed to consume 9 mW without voltage regulators.>
A 2-kb nondestructive readout memory chip has been built using an Nb/AlO/sub x//Nb Josephson-junction process with a 2.5- mu m design rule. A bitmap of 56% functional cells among 1.5 K tested cells, a read access time of 200 ps, an average cycle time of 500 ps without the decoder, and a power dissipation of 1.6 mW including peripheral circuits have been obtained. The decoding time is estimated to be 540 ps. The circuits in this 5-mm by 5-mm, 24-pin chip includes 2 K memory cells, 6-b decoder and drivers, serial-to-parallel and parallel-to-serial converters, and circuits for design of testability or timing measurements. More than 14000 junctions are used on the chip.>
Abstract : Lack of high-density, fast and memory has been a long-standing problem in superconducting digital electronics. Alternative Josephson-junction-based memory cells and peripheral circuits have intrinsic problems which impede the application of that kind of memory. The CMOS-Josephson hybrid memory idea was proposed in 1992 to circumvent this problem. In the present work we have designed and demonstrated a 64-kb CMOS-Josephson hybrid memory working at 1 GHz. In order to make the hybrid idea practical, a complete and comprehensive 4 K short-channel CMOS model for digital circuits was developed for this dissertation. It has been used in the design of the memory core and peripheral circuits. A fast hybrid interface circuit that transforms single-flux-quantum millivolt 2-ps pulse signals to CMOS volt-level signals has been studied and the optimized design has been completed. Using a nonvolatile cryogenic 3-T DRAM cell, the memory core is designed in such a way that the access time is much less than for room-temperature operation, not only because of the performance upgrade due to the temperature decrease but also because of a different reading mechanism. Fabricated by commercial submicron CMOS processes (0.25 microns and 0.18 microns) and a Nb/AlOx/Nb Josephson-junction process with 2.5 kA/cm2 tunneling current density, the memory chips were bonded together by direct wire-bonding and by flip-chip bump-bonding and tested at low frequencies, high frequencies, respectively. A subnanosecond access time is obtained both from simulations and experiments. The power for an interface circuit is measured to be 0.6 mW. The memory core consumes even less power. The total power consumption depends on the operation mode of the memory and is calculated to be 10 mW for reading and 28 mW for writing. Simulations also indicate that, with more advanced semiconductor and superconductor technologies, larger and faster hybrid memories are expected to be achievable in the future.
An experimental memory model for investigating the feasibility of a 16K RAM memory with Josephson junctions was fabricated and tested. There are nearly 4500 Josephson junctions in the design which includes array, line drivers, and address decoders. Storage element is a single flux-quantum (SFQ) cell arranged in a 2K array. Drivers and decoders are based on the principle of current steering in superconducting loops, which is a medium speed but low power approach. The measured read-access time of the model is approximately 10 ns. Power dissipation of the unselected chip is zero, whereas for a read/write cycle time of 30 ns, it amounts to about 10 /spl mu/W. Results indicate that a 16K chip is feasible electrically. The estimated access time and power dissipation are 15 ns and 40 /spl nu/W, respectively.
We present the design and test results of components for a superconductor Cryogenic Random Access Memory (CRAM). The 16-Kb RAM design consists of four 4-Kb sub-arrays (blocks) with a 400 ps access time (latency) and a 100 ps cycle time (throughput). Each 4-Kb RAM block comprises a row-accessed 32/spl times/128 memory cell array, bipolar line drivers, row decoders, and column sense circuits. The implementation of specially designed distributed Josephson junctions in the sensing circuits reduces the overall size of the blocks and allows the use of smaller dc control currents.
The paper first summarizes requirements for a main memory with Josephson junctions and reviews the work carried out on an experimental main memory model containing an array of single-flux-quantum cells, line drivers, and address decoders with a total of nearly 4500 Josephson junctions. In the second part, theoretical and experimental investigations on the y drive system, including sense circuit, are presented. The investigations deal with both the read and write phases. Finally, the on-chip logic circuits and the address decoders are discussed, and the experimental results presented. Drivers and decoders based on the principle of current steering in superconducting loops are intended to be used on a fully populated main-memory chip.